1059773-1

Instruction Sheet 408-8778 Installation Tool 1059773-1 for OSP* Hermetic Plug Connectors 10 AUG 11 Rev A PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. Handle (Torque Driver) Locking Handle in Open Position Locking Handle in Closed Position Collet Collet Adjustment Nut TOOL TE PART NUMBER REVIOUS PART NUMBER DESCRIPTION 1059773-1 4598-5014-54 Installation Tool 1059765-1 4598-3200-54 Replacement Head Assembly CONNECTOR TYPE PRESET TORQUE OSP Hermetic Plug Connector 18 In.-Lbs. Figure 1 1. INTRODUCTION 3. INSTALLATION AND REMOVAL Installation Tool 1059773-1 (Figure 1) is used to install and remove OSP Hermetic Plug Connectors. Figure 1 also lists the available replacement head that may be purchased from Tyco Electronics separately. 3.1. Installation NOTE i Dimensions in this document are in metric units [with U.S. customary units in brackets], unless otherwise indicated. NOTE The connector should bottom on a stop within the collet. i 2. Once the connector is in place in the collet, move the locking handle to the closed position. This secures the connector in the tool. 2. DESCRIPTION Installation Tool 1059773-1 contains an adjustablE handle that allows for torque settings between 6 in.lbs. and 30 in.-lbs. This tool also contains a connectorspecific head assembly. Once the tool head is adjusted for the specific connector, the installation of multiple connectors is made easy with a quick-release locking handle. A collet at the end of the assembly, holds the connector. A collet adjustment nut tightens the connector in the collet. The locking handle is used to secure the hermetic style plug in place during installation, and release the hermetic style plug assembly after installation. © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark 1. Place the hermetic plug connector in the collet. CAUTION Do not force the locking handle closed. If the handle does not easily close the collet tension may have to be adjusted. ! 3. If necessary, turn the adjustment nut until the connector is held snuggly in place. NOTE The collet adjusting nut is covered with a heat shrink tubing to help maintain adjustment. i CAUTION Damage to the connector may result if the collet is not properly adjusted. ! TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. 1 of 2 LOC B 408-8778 4. Holding the handle, turn the tool clockwise to thread the plug connector together. 4. Holding the handle, turn the tool counterclockwise to unthread the plug connector. 5. Continue turning the handle (and connector) until the drive handle makes a "clicking" sound. This clicking sound is an indication that the proper torque has been reached. 5. Move the locking handle to the open position to release the connector. 6. Move the locking handle to the open position to release the connector. 3.2. Removal 1. Place the hermetic plug connector into the collet. NOTE The connector should bottom on a stop within the collet. i The torque driver contains a 6.35 [.250] square drive which accepts the replacement head (shown in  Figure 1). 1. Pull the head off the standard 6.35 [.250] square drive. 2. Snap the replacement head (Figure 1) onto the square drive. 3. Order replacements from your TE representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write to: 2. Once the connector is in place in the collet, move the locking handle to the closed position. This secures the connector in the tool. CAUTION Do not force the locking handle closed. If the handle does not easily close the collet tension may have to be adjusted. ! 3. If necessary, turn the adjustment nut until the connector is held snuggly in place. NOTE 4. REPLACEMENT The collet adjusting nut is covered with a heat shrink tubing to help maintain adjustment. CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 For tool repair service, please contact a representative at 1-800-526-5136. 5. REVISION SUMMARY Since the previous release, the new company logo was applied. i CAUTION Damage to the connector may result if the collet is not properly adjusted. ! Rev A 2 of 2