10599-22-9

10599 SPECIFICATION CONTROL DRAWING CHEMINAX 70 OHM, AWG 22, 19 STRANDS OF AWG 34, DATA BUS CABLE, MIL-STD-1553A Date 3-20-12 Revision J THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS DIMENSIONS ARE NOMINAL VALUES IN INCHES UNLESS OTHERWISE DESIGNATED. .0295 .057 ± .003 CONDUCTORS AWG 22, 19 Strands of AWG 34, Tin-Coated Copper DIELECTRICS Radiation-Crosslinked, Modified ETFE Color - Light Blue / White ELECTRICAL CHARACTERISTICS CHARACTERISTIC IMPEDANCE 70 ± 5 ohms, Method C at 1 MHz MUTUAL CAPACITANCE 30 pF/ft. (maximum) ATTENUATION 1.0 dB/100 ft. (maximum) at 1 MHz ADDITIONAL REQUIREMENTS COMPONENT WIRE PRIOR TO CABLING (Test Procedures per SAE AS22759) CROSSLINKING PROOF TEST .131 SHIELD AWG 38, Tin-Coated Copper INSULATION (DIELECTRIC) ELONGATION TENSILE STRENGTH INSULATION FLAWS SPARK TEST IMPULSE TEST INSULATION RESISTANCE LOW TEMPERATURE-COLD BEND SHRINKAGE 300 ± 3°C for 7 hours, .500 inch mandrel, .500 lb., 2.5 kV dielectric test 50% (minimum) 5000 lbf/in2 (minimum) 3.0 kV (rms) 8.0 kV (peak) 5000 megohms for 1000 ft. (minimum) -65 ± 3°C for 4 hours, 1.00 inch mandrel, 1.00 lb., 2.5 kV dielectric test 200 ± 3°C for 6 hours, .125 inch (maximum) in 12 inches FINISHED CABLE (Test Procedures per NEMA WC 27500 unless otherwise specified) .147 (nominal) .154 (maximum) JACKET Radiation-Crosslinked, Modified ETFE Outer jacket color will be white (designated by a “-9" appended to the part number, e.g. 10599-22-9) unless otherwise specified. Designate outer jacket color with a dash number in accordance with MIL-STD-681. Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. BLOCKING CABLE LAY LENGTH CROSSLINKED VERIFICATION FLAMMABILITY (Method B of Spec 1200) JACKET ELONGATION TENSILE STRENGTH JACKET FLAWS SPARK TEST IMPULSE TEST JACKET THICKNESS LOW TEMPERATURE-COLD BEND SHIELD COVERAGE TEMPERATURE RATING VOLTAGE WITHSTAND (DIELECTRIC) 200°C for 6 hours .75 inch (minimum), 1.25 inch (maximum) 300 ± 5°C for 6 hours, 1.75 inch mandrel 3 seconds (maximum); 3 inch (maximum); no flaming of facial tissue 50% (minimum) 5000 lbf/in2 (minimum) 1.0 kV (rms) 6.0 kV (peak) .008 inch (nominal) -55 ± 5°C for 4 hours, 6.00 inch mandrel 90% (minimum) -65°C to 150°C 1000 volts (rms) (minimum) CABLE IDENTIFICATION: Outer jacket shall be marked in contrasting color at 12 inch (nominal) intervals as follows: “ 10599 - XXXXX “ (XXXXX = CAGE code) Example: “ 10599 - 06090 “ for US manufacture “ 10599 - K1010 “ for UK manufacture WEIGHT 17.6 lbs/1000 ft. (maximum) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Cheminax, Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 1-800-227-8816 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2007-2012 Tyco Electronics Corporation, All rights reserved.