0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
10603-0000-0

10603-0000-0

  • 厂商:

    HUMIREL(泰科)

  • 封装:

    -

  • 描述:

    GPPOWER

  • 数据手册
  • 价格&库存
10603-0000-0 数据手册
SPECIFICATION: THIS ISSUE: 35 Amendment 2, Issue 2 DATE: 6 August 2009 Raychem Wire and Cable REPLACES: 501 Oakside Avenue, Redwood City, CA 94063-3800 PAGE: Amendment 1, Issue 2 1 of 2 WIRE AND CABLE, ELECTRICAL, INSULATED, HIGH TEMPERATURE This amendment forms a part of Tyco Electronics/Raychem Specification 35, Issue 2 dated February 11, 1982. PAGE 1 Para. 3.1.1, Conductor: Change MIL-W-81044 to read "AS81044". Para. 3.1.3, Shield: Change MIL-C-27500 to read "WC27500". PAGE 2 and 3 Para. 4.3.2.1, 4.3.2.2, Accelerated Aging: Change MIL-W-81044 to read "AS81044" (4 places). PAGE 3 Para. 4.3.3, Acid-Gas Generation: Delete this test in its entirety (4.3.3, 4.3.3.1, 4.3.3.2 and Figure 1) and add new 4.3.3 as follows: 4.3.3 Aging Stability When required by the specification sheet, the finished wire shall be conditioned in accordance with Method 4031 of FED-STD-228 at the temperature and for the time specified in the applicable specification sheet. Elongation and tensile strength shall be determined in accordance with 4.3.7. PAGE 6 Para. 4.3.11, Solder Iron Resistance: Delete and replace with the following: “One inch (25 mm) of insulation shall be removed from each end of a 6-inch (150-mm) sample of 20 or 22 AWG 600V finished wire. The specimen shall then be bent into a loop and the ends tied together and weighted with a 150 ± 10 gram weight. The specimen shall then be suspended over the solder iron having a clean 1/4-inch (6-mm) nominal diameter bit and maintaining a bit temperature of 371 ± 10ºC. This condition shall be maintained for 60 seconds. The specimen shall then be subjected to the Voltage Withstand Test of 4.3.12.” © 2009 Tyco Electronics Corporation. All rights reserved. NOTE: ANY PRINTED COPY OF THIS DOCUMENT IS AN UNCONTROLLED COPY. Page 2 of 2 SPECIFICATION 35, AMENDMENT 2, ISSUE 2 PAGE 7 Para. 6.2, MIL-W-81044: Change MIL-W-81044 to read "AS81044" (2 places). PAGE 8 Table 1, Requirements for Finished Wire and Cable: Make the following modifications: • Acid-Gas Generation: Delete the listing for this test in its entirety. • Immersion: Delete fluid a) “Insulating Oil (VV-I-530)”. • Insulation Resistance: Delete this test for cable (i.e., replace “Applicable specification sheet” with “———”), and change the Test Method from MIL-C-915 to read “MIL-W-22759”. • Insulation Resistance: Delete this test for cable (i.e., replace “Applicable specification sheet” with “———”), and change the Test Method from MIL-C-915 to read “AS22759”. • Solder Iron Resistance: Change the requirement for finished wire from 60 seconds minimum to read “No dielectric breakdown”. • Test Methods column: Change MIL-W-81044 to read "AS81044" (3 places) and change MIL-C-27500 to read "WC27500" (2 places). • Add Aging Stability for finished wire as follows: Examination or Test Aging Stability Requirements Finished Wire Cable Applicable specification sheet ------------------- Test Methods Section 4.3.3 © 2009 Tyco Electronics Corporation. All rights reserved. NOTE: ANY PRINTED COPY OF THIS DOCUMENT IS AN UNCONTROLLED COPY.
10603-0000-0 价格&库存

很抱歉,暂时无法提供与“10603-0000-0”相匹配的价格&库存,您可以联系我们找货

免费人工找货