10614-24-9

10614 SPECIFICATION CONTROL DRAWING CHEMINAX 77 OHM, AWG 24, 19 STRANDS OF AWG 36, EMP HARDENED, DATA BUS CABLE, MIL-STD-1553 Date: 2-13-18 Revision: K THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE CHARACTERISTIC IMPEDANCE DESIGNATED. .0250 (.635 mm) .048 ± .002 (1.22 ± .05 mm) .032 (.813 mm) CONDUCTORS AWG 24, 19 Strands of AWG 36, Silver-Coated HighStrength Copper Alloy 30.0 pF/ft. (98.4 pF/m) (maximum) ATTENUATION 1.4 dB/100 ft. (4.59 dB/100 m) (maximum) at 1 MHz SURFACE TRANSFER IMPEDANCE 0.2 milliohms/meter (maximum) (Per SAE AS85485) at 30 MHz ADDITIONAL REQUIREMENTS COMPONENT WIRE PRIOR TO CABLING DIELECTRICS (Test procedures per SAE AS22759) Radiation-Crosslinked, CONDUCTOR RESISTANCE 26.5 ohms/1000 ft. (86.9 ohms/km) (nominal) Modified ETFE Colors - Light Blue/White CROSSLINKING PROOF TEST 300 ± 3°C for 1 hour, .500 inch (12.7 mm) mandrel, FILLERS .375 lb (170 g), 2.5 kV dielectric test Radiation-Crosslinked, INSULATION (DIELECTRIC) Modified ETFE ELONGATION 50% (minimum) TENSILE STRENGTH 5000 lbf/in2 (34.5 N/mm2) (minimum) INSULATION FLAWS SPARK TEST IMPULSE TEST .113 (2.87 mm) 77 ± 5 ohms, Method C at 1 MHz MUTUAL CAPACITANCE 1st SHIELD AWG 38, Tin-Coated Copper, Optimized 3.0 kV (rms) 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (1524 megohms-km) (minimum) LOW TEMPERATURE-COLD BEND -65 ± 3°C for 4 hours, .750 inch (19.1 mm) mandrel, 1.00 lb (454 g), 2.5 kV dielectric test SHRINKAGE 200 ± 3°C for 1 hour, .125 inch (3.18 mm) (maximum) in 12 inches (305 mm) FINISHED CABLE (Test procedures per NEMA WC 27500, unless otherwise specified) BLOCKING 200°C for 6 hours CABLE LAY LENGTH .75 inch (19.1 mm) (minimum), 1.25 inches (31.8 mm) (maximum) CROSSLINKED VERIFICATION 300 ± 5°C for 6 hours, 6.00 inch (152 mm) mandrel 2nd SHIELD .142 AWG 38, FLAMMABILITY 3 seconds (maximum); (3.61 mm) Tin-Coated Copper, (Method B of Spec 1200) 3 inches (76.2 mm) (maximum); Optimized no flaming of facial tissue JACKET ELONGATION 50% (minimum) TENSILE STRENGTH 5000 lbf/in2 (34.5 N/mm2) (minimum) JACKET FLAWS JACKET .158 SPARK TEST 1.0 kV (rms) Radiation-Crosslinked, (4.01 mm) IMPULSE TEST 6.0 kV (peak) Modified ETFE JACKET THICKNESS .008 inch (.203 mm) (nominal) LOW TEMPERATURE-COLD BEND -55 ± 5°C for 4 hours, 6.00 inch (152 mm) mandrel VOLTAGE WITHSTAND 1000 volts (rms) (minimum) (DIELECTRIC) WRAP .002 inch (.051 mm) thick (nominal), 25% overlap (minimum) The conductor AWG size and outer jacket color will be appended to 29.1 lbs/1000 ft. (43.3 kg/km) (maximum) the part number. Unless otherwise specified, outer jacket color will WEIGHT be white designated by a "-9" in accordance with MIL-STD-681, CABLE IDENTIFICATION: Outer jacket shall be marked in contrasting color at 12 (e.g. 10614-24-9). inch (305 mm) (nominal) intervals between marks as follows: "10614 RAYCHEM" .125 (3.18 mm) WRAP Mu-Metal Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. ENGINEERING REFERENCE TEMPERATURE RATING 150°C (maximum) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. TE Connectivity also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Cheminax, Raychem, TE Connectivity, and TE connectivity (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 Phone: 1-800-522-6752 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2009-2018 TE Connectivity Ltd. family of companies. All Rights Reserved.