1213819-2

Customer Manual Straight- Action Adapter Battery Powered Crimp Tool Kit 1213819- [ ] READ THIS FIRST ! 13 JUL 11 Rev E ORIGINAL INSTRUCTIONS SAFETY PRECAUTIONS 409-- 10058 .........................2 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. RECEVING/INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. DIE INSTALLATION AND REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1. Die Set Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2. Die Set Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.1. Battery Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.2. Crimping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5. PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.1. Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.2. Yearly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8. RETURN/REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 9. REVISION SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Safeguards are designed into this application equipment to protect operators and maintenance personnel from most hazards during equipment operation. However, certain safety precautions must be taken by the operator and repair personnel to avoid personal injury, as well as damage to the equipment. For best results, application equipment must be operated in a dry, dust--free environment. Do not operate equipment in a gaseous or hazardous environment. D ALWAYS wear appropriate ear protection. D ALWAYS wear appropriate eye protection. D ALWAYS wear approved eye protection when operating powered equipment. D ALWAYS keep guard(s) in place during normal operation. D NEVER wear loose clothing or jewelry that may catch in moving parts of the application equipment. D NEVER insert hands into installed application equipment. D NEVER alter, modify, or misuse the application equipment. E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. 1 of 8 LOC B 409- 10058 SAFETY PRECAUTIONS - - IMPORTANT SAFETY INFORMATION DANGER CAUTION DANGER CAUTION DANGER DANGER CAUTION DANGER CAUTION DANGER This unit should only be used by trained competent personnel. Read and understand the entire manual before using the equipment. NOTE: Keep all decals clean and legible, and replace when necessary. Always wear approved eye protection when using the equipment. 2 of 8 Rev E 409- 10058 TOOLING ASSISTANCE CENTER CALL TOLL FREE 1- 800- 722- 1111 (CONTINENTAL UNITED STATES AND PUERTO RICO ONLY) The Tooling Assistance Center offers a means of providing technical assistance when required. In addition, Field Service Specialists are available to provide assistance in the adjustment or repair of the application equipment when problems arise which your maintenance personnel are unable to correct. INFORMATION REQUIRED WHEN CONTACTING THE TOOLING ASSISTANCE CENTER When calling the Tooling Assistance Center regarding service to equipment, it is suggested that a person familiar with the device be present with a copy of the manual (and drawings) to receive instructions. Many difficulties can be avoided in this manner. When calling the Tooling Assistance Center, be ready with the following information: 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. Customer name Customer address Person to contact (name, title, telephone number, and extension) Person calling Equipment number (and serial number if applicable) Product part number (and serial number if applicable) Urgency of request Nature of problem Description of inoperative component(s) Additional information/comments that may be helpful 1725840--1 BATTERY CHARGER VOLTAGE 110 V RAM RETRACT SWITCH Yes Europe North America 1725840--2 1725840--1 220 V 110 V Yes No Europe United Kingdom 1725840--2 1725840--3 220 V 220 V No Yes BATTERY TOOL KIT REGION OF USE BATTERY CHARGER 1213819--1 North America 1213819--2 1213819--3 1213819--4 1213819--5 Rev E 3 of 8 409- 10058 Battery Lock Battery Powered Crimp Tool Release Switch (1213819-- 1, - 2, and - 5 Only) Moving Die Holder Battery Cartridge 1725839-- 1 Stationary Die Holder Trigger Straight-- Action Adapter Figure 1 1. INTRODUCTION Straight--Action Adapter Battery Powered Crimp Tool Kit 1213819--[ ] consists of the battery powered crimp tool (with the Straight--Action Adapter assembly installed), as well as two rechargeable battery cartridges (1725839--1) to power the tool. See Figure 1. Each kit has a battery charger. The battery charger part number, its voltage, and the kit’s region of use are listed in the table on Page 3. A battery tool may have a release switch to retract the ram as listed in the table below. The Straight--Action Adapter Battery Powered Crimp Tool Kit 1213819--[ ] is designed to accept various crimping die assemblies that are sold separately and are available from TE Connectivity. For crimping die set information concerning wire preparation, crimping procedures, maintenance, inspection, and repair, refer to the applicable instructions for the appropriate crimping die set. Specifications are listed in Figure 2. 4 of 8 Rev E 409- 10058 CRIMP TOOL (with Battery Installed) 343 mm [13.5 In.] Length Width Depth 60 mm [2 3/8 In.] 80 mm [3 1/8 In.] Mass/Weight (w/Battery) 1.3 kg [2.9 lb.] Sound Level Vibration Hydraulic Oil CRIMPING CAPACITIES 75 dBA at 1 Meter < 2.5 m/s2 Shell Tellus T 15 Maximum Crimping Force Average Crimping Time Average Crimps Per Charge BATTERY Charging Voltage 15.6 kN [1.75 Tons] 2 Seconds Approximately 150 Charging Time 40 Min 9.6 V Figure 2 2. RECEIVING/INSPECTION The Straight--Action Battery Powered Crimp Tool Kit 1213819--[ ] is thoroughly inspected during and after assembly. Prior to packaging and shipping, a final series of tests and inspections is made to ensure proper function of the tool. The following inspection should be performed as a safeguard against potential problems generated in transit. 1. In a well--lighted area, carefully uncrate the tool and inspect each component as it is removed from the crate. 2. Thoroughly inspect each component for evidence of damage that may have occurred in transit. If any of the components are damaged, file a claim against the carrier and notify TE immediately. 3. Keep this manual and all drawings and product samples with the tool for the benefit of operation and maintenance personnel. The crimp tool should be inspected at regularly scheduled intervals, depending on care, degree of operator skill, the type and size of product being crimped, and environmental conditions. At a minimum, the tool should be inspected after every 40 hours of use. 3. DIE INSTALLATION AND REMOVAL CAUTION Do not operate the tool without the Straight--Action Adapter installed. Damage to the ram or seals can result. ! CAUTION Do not operate the tool without a die set installed. Damage to the adapter can result. ! Straight--Action Adapter Battery Powered Crimp Tool Kit 1213819--[ ] comes with the straight--action adapter assembly already installed on the battery--powered hand tool. The only installation required is the installation of the dies. DANGER Rev E To avoid personal injury, be sure to exercise extreme caution when handling the crimp tool. Remove the battery before installing or removing the dies. 5 of 8 409- 10058 3.1. Die Set Installation (Figure 3 ) If dies to be installed in the tool require insulation adjustment, refer to the instruction sheet packaged with the dies for adjustment, then proceed as follows: 1. Remove the battery from the tool. 2. Mate the die assembly and insert it into the tool yoke. See Figure 3. 3. Position the stationary die in the stationary die holder. Turn the die retaining screw sufficiently to hold the die in place. Do not tighten the screw. 4. Position the moving die in the moving die holder. Turn the die retaining screw sufficiently to hold the die in place. Do not tighten the screw. 5. Replace the battery and check the alignment by pulsing the trigger to (slowly) close the dies, making sure the anvil and indenter are properly aligned. 6. With the dies closed, tighten the die retaining screws. Color Code Moving Die Stationary Die Die Retaining Screw Locator Dies Installed in Tool Yoke Figure 3 3.2. Die Set Removal To remove or change the dies, simply loosen the die retaining screws and remove the dies. 4. OPERATION 4.1. Battery Installation and Removal (Refer to Figure 1) NOTE i The Batteries Directive 2006/66/EC introduces new requirements from September 2008 on removability of batteries from waste equipment in EU Member States. To comply with this Directive, this device is designed to allow the rechargeable battery pack to be easily removed by the end--user when it needs to be replaced. To install the battery, slide the battery into the bottom of the crimp tool until it can go no further. There will be an audible “click” of the battery lock to indicate that the battery has been properly installed. To remove the battery, disengage the battery lock by applying pressure on the lock toward the bottom of the tool and slide the battery away from the tool. DANGER Always dispose of the old battery pack in an environmentally--responsible way, in accordance with local waste regulations. Where possible, please recycle the battery cartridge. Contact your local authority for details of battery recycling locations in your area. 4.2. Crimping The following procedure provides only general information concerning crimping. Refer to the instructions packaged with the dies for detailed information, including wire stripping dimensions and instructions for positioning terminals and splices in the dies. 6 of 8 Rev E 409- 10058 DANGER To avoid personal injury, keep fingers clear of the crimping area. To operate the Straight--Action Adapter Battery Powered Crimp Tool 1213819--[ ]: 1. Insert the terminal into the dies. 2. Depress the trigger to advance the moving jaw in order to hold the terminal in place. Do NOT deform the terminal body. 3. Place a pre--stripped wire in the barrel of the terminal. 4. Depress and hold the trigger to complete the crimp. The crimp tool returns automatically to the first position of its cycle when the crimp is complete. NOTE i CAUTION If it is necessary to retract the ram before a crimping cycle is completed, push the release switch. Pushing the release switch will result in the complete retraction of the ram. Only kits 1213819--1, - 2, and - 5 have a release switch. This tool is not designed for continuous operation. After 100 cycles, allow the crimp tool to cool for 15 minutes. ! 5. PREVENTIVE MAINTENANCE 5.1. Daily Maintenance Perform the following maintenance on a daily basis: 1. Inspect the die set, adapter assembly for wear or damage such as cracks, gouges, or chips. 2. Inspect the crimp tool for damage or leaks. If damage is detected, return the tool to TE for repair 3. Clean the tool, removing accumulations of dirt and grease on the head, particularly in areas where the dies are installed and terminals are crimped. Wipe the entire tool frequently with a clean, lint--free cloth. DO NOT use objects that could damage the tool. 4. Make sure that the die retaining screws are in place and are tight. 5.2. Yearly Maintenance Once a year, or every 10,000 cycles (whichever comes first) The Straight--Action Adapter Battery Powered Crimp Tool should be returned to TE for inspection. 6. SPARE PARTS S Battery: 1725839--1 S Charger: 1725840--1 (120 V, US), 1725840--2 (220 V, EU), 1725840--3 (220 V, UK) 7. TROUBLESHOOTING (Figure 3) Prior to beginning troubleshooting procedures, be sure the battery is operational. 1. Be sure that the battery is charged. Recheck the battery after several minutes to ensure that the battery is holding its charge. 2. Use a nonflammable contact cleaner or pencil eraser to clean the the electrical contacts on the battery and crimp tool. 3. Reinstall the battery and check the crimp tool again. Rev E 7 of 8 409- 10058 PROBLEM Tool is inoperative. p Dies stop during operation. Crimp tool loses oil. PROBABLE CAUSE REMEDY Dirt, contaminants, etc, in ram area of tool Return tool to TE. Crimp tool battery contacts damaged Reform the contacts. Tool components are worn or damaged. Return tool to TE. Oil level is low. Return tool to TE. Air in the hydraulic system. Pull the trigger and hold the retract button simultaneously. Hold for approximately 10 seconds. Damaged internal seal. Return tool to TE. Figure 4 8. RETURN Order replacement parts through your TE Representative, or call 1.800.526.5142; or send a facsimile of your purchase order to 1.717.986.7605; or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105--3608 9. REVISION SUMMARY S Updated document to corporate requirements S Added new text to Section 4, OPERATION 8 of 8 Rev E