Automotive Relays
PCB Single Relays
Power Relay K (Sealed)
Ŷ Limiting continuous current 45A
Ŷ Wide voltage range
Typical applications
ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,
hazard warning signal, heated front screen, heated rear screen, ignition,
lamps front/rear/fog light, interior lights, main switch/supply relay, seat
control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,
wiper control.
Contact Data
Typical applications
Contact arrangement
Rated voltage
F076_fcw2b
Coil Data
Resistive/inductive
Headlights
loads
capacitive loads
1 form C, 1 CO
12VDC
12VDC
A/B (NO/NC)
45/30A
40/25A
Rated current
Limiting continuous current1)
23°C
45/30A
40/25A
85°C
30/25A
25/20A
2)
Limiting making current
100/30A
180/60A
Limiting breaking current3)
60/30A
60/30A
Contact material
AgNi0.15
SgSnO2
Min. recommended contact load
1A at 5VDC4)
Initial voltage drop, at 10A, typ./max.
20/300mV
Operate/release time
typ. 5/3ms5)
Electrical endurance
>2x105 ops.
>105 ops.
at 13.5VDC, 40A
up to 4x60W
Mechanical endurance, DC coil
>107 ops.
1) Measured on 70x70x1.5mm epoxy PCB FR4 with 35cm2 (double layer 105µm) copper
area. Cable cross section 6mm². Boundary conditions: 180°C coil temperature; 130°C
solder joint. Solder joint results above 130°C on request. The load circuit shall withstand
current applied on 40A MAXI fuse.
2) The values apply to a resistive or inductive load with suitable spark suppression and at
maximum 13.5VDC load voltages.
3) For a load current duration of maximum 3s for a make/break ratio of 1:10.
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay
coil increases the release time and reduces the lifetime caused by increased erosion
and/or higher risk of contact tack welding.
Max. DC load breaking capacity
TE0556-E
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
Rated coil voltage
Coil versions, DC coil
Coil
Rated
Operate
code
voltage
voltage
VDC
VDC
001
12
6.9
12VDC
Release
voltage
VDC
1.2
Coil
resistance
Ω±10%
90
Rated coil
power
W
1.6
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coils on request.
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
500VACrms
500VACrms
Other Data
EU RoHS/ELV compliance
Ambient temperature, DC coil
Climatic cycling with condensation,
EN ISO 6988
Temperature cycling (shock),
IEC 60068-2-14, Na
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1
compliant
-40 to +85°C6)
3 cycles, storage 8/16h
20 cycles, -40/+85°C (dwell time 1h)
6 cycles, upper air temperature 55°C
Coil operating range
TE0555-6
Does not take into account the temperature rise due to the contact current
E = pre-energization
1
06-2016, Rev. 0616
www.te.com
© 2016 TE Connectivity.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Automotive Relays
PCB Single Relays
Power Relay K (Sealed) (Continued)
Terminal Assignment
Bottom view on solder pins
Other Data (continued)
Damp heat constant,
56 days, upper air temperature 55°C
IEC 60068-2-3, method Ca
RT III – immersion cleanable version
Corrosive gas,
IEC 60068-2-42
10 days
IEC 60068-2-43
10 days
Vibration resistance (functional),
IEC 60068-2-6 (sine pulse form),
acceleration, acc. to position
10 to 200Hz, 20 to 40g7)
Shock resistance (functional),
IEC 60068-2-27 (half sine form single pulses),
acceleration, acc. to position
8ms 30g7)
Terminal type
PCB
Weight
sealed version
approx. 22g (0.77oz)
open version
approx. 19g (0.67oz)
Solderability (aging 3: 4h/155°C)
for leaded process (Tm = 183°C),
for Pb-free process (Tm = 217°C),
IEC 60068-2-20
Ta, method 1, hot dip 5s, 215°C
Storage conditions
according IEC 600688 8)
Packaging unit
sealed version
525 pcs.
1 form C, 1 CO
TE1086-A1
6) See coil operating range DC.
7) No change in the switching state >10μs.
8) For general storage and processing recommendations please refer to our Application
Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/
Mounting Hole Layout
Bottom view on solder pins
Dimensions
26.1 ±0.4
8.5 ±0.2
16.0 ±0.3
21.1 ±0.4
10.2 ±0.2
6.0 ±0.2
Assembly and
positioning aid
3.4 ±0.1
ø 1.3 +0.1
ø 2.3 +0.1
3.4 ±0.6
3.4 ±0.1
6.6 ±0.3
21.2 ±0.3
12.1 ±0.1
2.2 ±0.1
3.3 ±0.1
ø 2.1 +0.1
3.0 ±0.5*)
2.5 – 3.0
ø 2.3 +0.1
ø 2.3 +0.1
0.55 ±0.25
2.3 ±0.2
Terminals tinned
* Additional tin tops
max. 1.5mm
)
13.3 ±0.2
TE0580-X2
2
06-2016, Rev. 0616
www.te.com
© 2016 TE Connectivity.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Automotive Relays
PCB Single Relays
Power Relay K (Sealed) (Continued)
Product code structure
Typical product code
V23076
-A
1
001
-C
13
3
Type
V23076
Power Relay K, sealed
Terminal
A
PCB
Design
1
Single relay
Coil
001
12VDC
Contact type
C
Single contact
Contact material
13
AgNi0.15
Contact arrangement
3
1 form C, 1 CO
D
Single contact
14
AgSnO2
Product code
Terminal/Encl.
Design
Coil
Contact
Contact mat.
Arrangement
Part number
V23076-A1001-C133
V23076-A1001-D143
PCB, sealed
Single relay
12VDC
Single
AgNi0.15
AgSnO2
1 form C, CO
1393277-4
1393277-6
3
06-2016, Rev. 0616
www.te.com
© 2016 TE Connectivity.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.