Automotive Relays
PCB Single Relays
Power Relay K (Sealed)
n
Limiting continuous current 45A
Wide voltage range
n 24VDC coil versions available
n
Typical applications
ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,
hazard warning signal, heated front screen, heated rear screen, ignition,
lamps front/rear/fog light, interior lights, main switch/supply relay, seat
control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,
wiper control.
F076_fcw2b
Contact Data
Typical applications Resistive/inductive
Resistive/inductive
Indicator lamps
Headlights,
Headlights
loads
loads
capacitive loads
capacitive loads
Contact arrangement
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form A, 1 NO
1 form C, 1 CO
Rated voltage
12VDC 12VDC 12VDC 12VDC 12VDC
A/B (NO/NC) A/B (NO/NC)
Rated current
45A 45/30A 30A 40A 40/25A
Limiting continuous current
23°C
45A 45/30A 30A 40A 40/25A
85°C
30A 30/25A 25A 25A 25/20A
1)
Limiting making current
100A
100/30A
120A3) 180A 180/60A
Limiting breaking current2)
60A 60/30A 60A 60A 60/30A
Contact material
AgNi0.15
AgNi0.15
AgSnO2 AgSnO2 AgSnO2
Min. recommended contact load
1A at 5VDC4)
Initial voltage drop, at 10A, typ./max.
20/300mV
Operate/release time
typ. 5/3ms5)
Electrical endurance
>2x105 ops.
>2x105 ops.
>2.2x106 ops.
>105 ops.
>105 ops.
at 13.5VDC, 40A
at 13.5VDC, 40A
up to 8x21W
up to 4x60W
up to 4x60W
Mechanical endurance, DC coil
>107 ops.
1)
2)
3)
4)
5)
The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.
For a load current duration of maximum 3s for a make/break ratio of 1:10.
Corresponds to a peak inrush current on initial actuation (cold filament).
See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/
For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher
risk of contact tack welding.
Max. DC load breaking capacity
Coil operating range
TE0556-E
TE0555-6
Does not tak
the temperat
the contact c
E = pre-ener
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
06-2014, Rev. 0614
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Does not take into account the temperature rise due to the contact current
E = pre-energization
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
1
Automotive Relays
PCB Single Relays
Power Relay K (Sealed) (Continued)
Coil Data
Rated coil voltage
12VDC / 24VDC
Coil versions, DC coil
Coil
Rated
Operate
Release
Coil
Rated coil
code voltage voltage voltage
resistance power
VDC VDC VDC
Ω±10% W
001 12 6.9 1.2 90 1.6
022 24 14.1 2.4 362 1.6
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coils on request.
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
500VACrms
500VACrms
Other Data
EU RoHS/ELV compliance
compliant
Ambient temperature, DC coil
-40 to +85°C6)
Climatic cycling with condensation,
EN ISO 6988
3 cycles, storage 8/16h
Temperature cycling (shock),
IEC 60068-2-14, Na
20 cycles, -40/+85°C (dwell time 1h)
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1
6 cycles, upper air temperature 55°C
Terminal Assignment
Bottom view on solder pins
Other Data (continued)
Damp heat constant,
56 days, upper air temperature 55°C
IEC 60068-2-3, method Ca
RT III – immersion cleanable version
Corrosive gas,
IEC 60068-2-42
10 days
IEC 60068-2-43
10 days
Vibration resistance (functional),
IEC 60068-2-6 (sine pulse form),
acceleration, acc. to position
10 to 200Hz, 20 to 40g7)
Shock resistance (functional),
IEC 60068-2-27 (half sine form single pulses),
acceleration, acc. to position
8ms 30g7)
Terminal type
PCB
Weight
sealed version
approx. 22g (0.77oz)
open version
approx. 19g (0.67oz)
Solderability (aging 3: 4h/155°C)
for leaded process (Tm = 183°C),
for Pb-free process (Tm = 217°C),
IEC 60068-2-20
Ta, method 1, hot dip 5s, 215°C
Storage conditions
according IEC 600688 8)
Packaging unit
sealed version
525 pcs.
6) See coil operating range DC.
7) No change in the switching state >10μs.
8) For general storage and processing recommendations please refer to our Application
Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/
Dimensions
26.1 ±0.4
1 form C, 1 CO
1 form A, 1 NO
8.5 ±0.2
21.1 ±0.4
*)
*)
Assembly and
positioning aid
TE1091-B1
3.4 ±0.1
TE1086-A1
3.4 ±0.1
*) Terminals 4 to be bridged
21.2 ±0.3
Mounting Hole Layout
Bottom view on solder pins
16.0 ±0.3
3.0 ±0.5 *)
2.5 – 3.0
10.2 ±0.2
0.55 ±0.25
6.0 ±0.2
*) additional tin tops
max. 1.5 mm
ø 1.3 +0.1
ø 2.3 +0.1
3.4 ±0.6
6.6 ±0.3
12.1 ±0.1
TE0579-I2
Terminals tinned
2.2 ±0.1
3.3 ±0.1
ø 2.1 +0.1
ø 2.3 +0.1
ø 2.3 +0.1
2.3 ±0.2
13.3 ±0.2
TE0580-L2
2
06-2014, Rev. 0614
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Automotive Relays
PCB Single Relays
Power Relay K (Sealed) (Continued)
Product code structure
Typical product code V23076 -A 1 022 -C 13 3
Type
V23076 Power Relay K, sealed
Terminal
A
PCB
Design
1
Single relay
Coil
001 12VDC
Contact type
C
Single contact
Contact material
13
AgNi0.15
15
AgSnO2 (Special)
Contact arrangement
2
1 form A, 1 NO
Product code
V23076-A1001-C133
V23076-A1001-D143
V23076-A3001-C132
V23076-A3001-D142
V23076-A3001-D1521)
V23076-A1022-C133
V23076-A1022-D143
V23076-A3022-C132
V23076-A3022-D142
V23076-A3022-D1521)
Terminal/Encl.
PCB, sealed
3
Single relay
022
24VDC
D
Single contact
14
AgSnO2
3
1 form C, 1 CO
Design
Single relay
Coil
12VDC
24VDC
Contact
Single
Contact mat.
AgNi0.15
AgSnO2
AgNi0.15
AgSnO2
AgSnO2 special
AgNi0.15
AgSnO2
AgNi0.15
AgSnO2
AgSnO2 special
Arrangement
1 form C, CO
1 form A, NO
1 form C, CO
1 form A, NO
Part number
1393277-4
1393277-6
1-1393277-4
1-1393277-7
1-1414175-0
1393277-8
1393277-9
1-1393277-8
1-1393277-9
4-1904101-8
1) For indicator lamps.
06-2014, Rev. 0614
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
3
