1462039-1

AXICOM IM RELAY SIGNAL RELAYS INTRODUCTION TE Connectivity (TE)’s Axicom IM signal relays, as part of our smallest types of electromechanical relays, offer a wide and deep range of variations suitable for many applications. The IM series are equipped with 2 changeover contacts in both monostable or bistable versions, available in multiple coil solutions, performance types and pin layouts. FEATURES • Slim line 10x6mm, low profile 5.65mm and min. board-space 60mm². • Switching current 2/5A, switching power 60W/62.5VA and switching voltage 220VDC/250VAC. • Low coil power consumption, 140mW standard, 100mW for high sensitive version, 50mW for ultra high sensitive version and 100mW for bistable version. • High dielectric and surge capability up to 2500Vrms between open contacts and 2500Vrms between coil and contacts. • High mechanical shock resistance up to 50g functional. APPLICATIONS • Telecommunication • Access and transmission equipment • Optical network terminals • Modems • Office and business equipment • Consumer electronics • Measurement and test equipment • Industrial control • Medical equipment • HVAC APPROVALS • UL 61810-1 (former UL 508) File No. E214025 U 3) Technical data of approved types on request Buyer entirely assumes the risk and all liability relating to (a) assessing the suitability for Buyer’s intended use of the Products and of any system design or drawing and (b) determining the compliance of Buyer’s use of the Products with applicable laws, regulations, codes and standards. For more info on the exclusive and applicable warranty, please refer to TE standard warranty terms. Maximum switching current 2ÊA Maximum swichting voltage AXICOM IM RELAY SIGNAL RELAYS Maximum switching capacity CONTACT DATA Minimum switching voltage Thermoelectric potential Standard, C (Standard and high dielectric version) Contact arrangement (High current version) (High contact stability version) 2 form C, 2 CO 220VDC, 250VAC 220VDC, 250VAC 220VDC, 250VAC Rated current 2A 5A1) 2A Limiting continuous current 2A 5A1) 2A Max. switching voltage Switching power Contact material Contact style Initial contact resistance / < 100 mΩ P measuring condition: 10 mA / 20 mV D, I Standard, C Electrical CC0 Contact category 0 (High Performance endurance (≤ 30 mV and / ≥ 10 mA) (High (Standard high contact type cable load open end current stability dielectric version) version) version) Resistive load at 125 Vdc / 0.24 A - 30 W at 220 Vdc / 0.27 - 60 NO W only 30VDC, 2A, A 60W, at 250 Vac / 0.25 A - 62.5 110VDC, 0.3A, 33W VA at 30 Vdc / 1 A - 30 W 60W 220VDC, 0.27A, UL contact at 30 Vdc / 2 A - 60 W rating Mechanical endurance 125VAC, 0.5A, 62.5VA 250VAC, 0.25A, 62.5VA UL contact ratings 30VAC, 2A, 62.5VA, NO only (IMxxI, IMxxD) 60W, 62.5VA PdRu +Au covered AgNi +Au covered PdRu +Au covered Twin contacts Twin contacts I: single contacts Twin contacts Minimum switching voltage min. 1x108 operations MAX. DC LOAD BREAKING CAPACITY 100μV 10⁹Ω 0.200ʱÊ0.004 0.126ʱÊ0.006 0.087ʱÊ0.006 0.015 N/A SMT Version SMT Version Gull Wings Gull Wings max. 0.75g 10.0±0.08 2.80 5.08 3.20 2.20 J- 5.7±0.3 10.0±0.08 Moisture sensitive level, JEDEC 5.7±0.3 10.0±0.08 6.0±0.08 J-STD-020F MSL3 related10.0±0.08 only 0.4 0.4 to SMT relays packed in orginal 0.4 3.2±0.1 5.08±0.1 Resistance to dry-packs. Calculated shelf life in 5.08±0.1 0.4 Cop 0.4 7.5±0.3 0.4 Coplanarity ≤ 0. soldering heat SMT sealed bag: 36 months at