1617069-9

DS13 Series High Performance Solid State Relays DC solid state relay for loads up to 2A @ 60Vdc Product Facts status provides a built-in test function which provides a logic “0” when the input circuit is energized and functional. The relay is packaged into a custom hermetically sealed lowprofile 8-pin ceramic DIP package, with through hole or surface mount pins. co m protection and a separate input control status line. The overload feature provides protection of the relay, load and load circuit wiring in the event of a sustained current overload or short circuit while the relay is on or when it is turned on into a short. The control s. DS13 series SSRs employ state of the art photovoltaic optical isolation and power MOSFET output chips for ultra-reliable high speed switching of DC loads up to 2 amps, with low on-resistance. Standard options include integral current overload/short circuit DSCC Dwg. No. DS13-1Y 90091-008 Relay Version DS13-1000 90091-004 DS13-1001 90091-006 Relay w/ control status DS13-1002 90091-002 Relay w/ short circuit protection and control status nt CII Part No. Basic relay Relay w/ short circuit protection ne po ■ Standard options: short circuit/overload protection and control status. ■ Optically coupled all solid state relay. ■ TTL & CMOS compatible input. ■ Low on-resistance power MOSFET output. ■ Tested per MIL-R-28750 and approved to DSCC drawing 90091. ■ All versions available with Tyco Electronics “W” level screening for CII relays. Note: Add suffix “S” to part number for surface mount versions. m 2 Terminal Input Configuration S1 co Direct Drive R Series (+) Output Vcc Load lin e 2 R Series Vcc (+) Output 4 1 Control V Load TTL Drive on 8 Return Control (-) Output Load Return 4 8 Return 5 V Load Load Load Return Load V Load Load Load Return 2 5 Load 1 Load (-) Output O C TTL 3 Terminal Input Configuration With Status Without Status V Status R Status Vso Vcc Status (+) Output Output 1 7 (+) Output Load V Load Vcc 4 V Control Control 2 V Control Control 8 5 Return Load (-) Output Load Return 1 4 8 5 2 Return (-) Output © 2004 by Tyco Electronics Corporation. All Rights Reserved. CII and TYCO are trademarks. 1 Catalog DS13-TBD Issued 1-04 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 DS13 Series High Performance Solid State Relays DC solid state relay for loads up to 2A @ 60Vdc (Continued) Environmental Characteristics Electrical Specifications (-55°C to +105°C unless otherwise specified) Ambient Temperature Range: Operating: -55°C to +105°C. Storage: -55°C to +125°C. Input (2 terminal configuration) Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Input current (max.) @ 5Vdc Vibration Resistance: 100 G’s, 10-3,000 Hz. 15mAdc (Notes 1 & 2, Figures 1 & 2) Must turn-on voltage 3.8Vdc Shock Resistance: 1,500 G’s, 0.5 ms pulse. Must turn-off voltage 1.5Vdc Reverse voltage protection -32Vdc Constant Acceleration Resistance: 5,000 G’s. Input (3 terminal configuration) Control voltage range 0 - 18 Vdc Control current (max.) 240µAdc @ 5V, 1mA @ 18V 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) m Input supply voltage range (Vcc) Mechanical Characteristics Must turn-on voltage Weight (max.): .07 oz. (2 grams) Must turn-off voltage Materials: Case: DIP, hermetically sealed, ceramic Pins: Gold plated Dielectric Strength (min.) 15mAdc (Notes 1 & 2, Figures 1 & 2) co Input current (max.) @ 5Vdc s. I/O Insulation Resistance (min.) @ 500Vdc nt Capacitance (max.) Output ne Continuous load current (max.) @ 25°C, without short circuit protection Continuous load current (max.) @ 25°C, with short circuit protection Continuous load voltage (max.) po Transient blocking voltage (max.) 3.2Vdc 1,000V rms 109 ohms 10pF 2.0Adc (Figure 5, Note 3) 1.0Adc (Figure 5, Note 3) 60Vdc 80Vdc (Note 4) On resistance (max.) @ Tj = 25°C, IL = 100ma, with short circuit protection 0.45 ohm (Note 5, Figure 4) On resistance (max.) @ Tj = 25°C, IL = 100ma, without short circuit protection 0.22 ohm (Note 5, Figure 4) 0.6Vdc Output voltage drop (max.), without short circuit protection 0.75Vdc m Output voltage drop (max.), with short circuit protection 100µAdc co Off-state leakage current (max.) @ 60Vdc Turn-on time (max.) 1.5 ms (Figure 3) Turn-off time (max.) .25 ms (Figure 3) 100V / µs lin e dv/dt (min.) Electrical system spike ±600Vdc (Note 4) Junction temperature (max.) on 0.3Vdc 150°C Thermal resistance (max.), junction to ambient 80°C/W Thermal resistance (max.), junction to case 20°C/W Status Status supply voltage 30Vdc Status sink current (max.) @ Vstatus≤ 0.3Vdc 2mAdc (Note 7) Status leakage current (max.) @ 15Vdc 4µAdc Short Circuit Protection See Figure 6, Note 7 2 Catalog DS13-TBD Issued 1-04 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 DS13 Series High Performance Solid State Relays DC solid state relay for loads up to 2A @ 60Vdc (Continued) Figure 1 - Maximum Input Current vs. Input Voltage Figure 2 - Series Resistance vs. Vcc Supply Voltage (Note 1) 2000 9 6 1500 1000 m 12 500 3 0 0 5 10 15 20 25 30 40 50 60 0 Figure 3 - Output Turn-on and Turn-off Timing Low m Off 90% 10% On T Off lin e TOn co Pin 4-5 20 25 30 35 ne Normalized On Resistance Factor (NF) High Pin 2 V Output 15 Vcc (Volts) Figure 4 - On-Resistance vs. Temperature (Note 6) po Control 10 nt Input Voltage, Vcc (Vdc) V 5 s. 0 co 15 R Series (ohms) Input Current (mA) 18 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 25 50 75 100 125 on Junction Temperature (°C) Figure 5 - Temperature Derating Curve Figure 6 - Typical Current Trip Levels DS13-1Y DS13-1001 1.5 1.0 DS13-1000 DS13-1002 0.5 0.0 -55 15 25 35 45 55 65 75 85 95 105 115 125 Surge Current (amps) Load Current (amps) 5 2.0 Ambient Temperature (°C) 4 3 +25°C -55°C 2 +105°C 1 0 0.01 0.1 1 10 100 1000 Time (seconds) 3 Catalog PS13-TBD Issued 1-04 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 DS13 Series High Performance Solid State Relays DC solid state relay for loads up to 2A @ 60Vdc (Continued) Figure 7 - Outline Dimensions Through-Hole Mount Version .010 ± .002 (.25 ± .05) 6 PLS .560 MAX. (14.22) 8 7 Surface Mount Version .560 MAX. (14.22) 5 7 8 .485 +.010, –.005 .395 MAX. (12.32 +.25, –.13) (10.03) .435 MAX. (11.05) 2 4 SIDE INDEX MARK FOR PIN 1 .016 +.010, –.005 (.41 +.25, –.13) 6 PLS .155 MAX. (3.94) s. .125 (3.18) .100 (2.54) .300 (7.62) .018 ± .002 (.46 ± .05) 6 PLS po ne .018 ± .002 (.46 ± .05) 6 PLS .300 (7.62) .155 MAX. (3.94) .036 +.010, –.005 (.91 +.25, –.13) 6 PLS lin e co m .100 (2.54) 1 4 2 TOP INDEX MARK FOR PIN 1 SIDE INDEX MARK FOR PIN 1 nt .150 ± .015 (3.81 ± .38) 6 PLS .125 (3.18) .010 ± .002 (.25 ± .05) 6 PLS .025 (.64) 6 PLS co 1 TOP INDEX MARK FOR PIN 1 .395 MAX. (10.03) m .400 ± .015 (10.16 ± .38) 5 Notes 1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value form the curve. on 2.Vcc = 5Vdc for all tests unless otherwise specified. 3.All DS13 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent damage. Inductive loads must be diode suppressed. 4.Transient blocking voltage & electrical system spike tests are performed per MIL-STD-704 (28Vdc systems). 5.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25°C by normalized on-resistance factor from curve (Fig. 4). 6.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 90091. Load circuit series inductance for “load shorted” mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10 Hz. To calculate maximum on-resistance at any temperature, use the following equation: R(on) = R(on) @ 25°C x NF (without short circuit protection) and R(on) = 0.2 x NF + .21 (with short circuit protection) where NF = normalized on-resistance factor from Fig. 4. 7.Proper operation of the status feedback requires a status pull-up resistor. Select the status resistor such that it limits status output current to 2mA: R status = V status – 0.3V / 2mA. DS13-TBD–PDF–KRG–1-04 4 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967