186836-001

EPD6314 SPECIFICATION CONTROL DRAWING CHEMINAX Date: Revision: DATA BUS CABLE, MULTIPLEX 8-2-04 L THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS DIMENSIONS ARE NOMINAL VALUES IN INCHES UNLESS OTHERWISE DESIGNATED. CONDUCTOR AWG 24, 19 Strands of AWG 36, Nickel-Coated High Strength Copper Alloy, Unilay .0235 DIELECTRIC Radiation-Crosslinked, Modified ETFE Color - Blue / White .046 FILLERS Radiation Crosslinked Modified ETFE .031 ELECTRICAL CHARACTERISTICS CHARACTERISTIC IMPEDANCE 77 ± 5 ohms, Method C at 1 MHz CAPACITANCECONDUCTOR TO CONDUCTOR CONDUCTOR TO SHIELD 30 pF/ft. (maximum) at 1 MHz 42 pF/ft. (maximum) at 1 MHz ATTENUATION 1.5 dB/100 ft. (maximum) at 1 MHz ADDITIONAL REQUIREMENTS COMPONENT WIRE PRIOR TO CABLING (Test Procedures per MIL-W-22759) CROSSLINK PROOF 300 ± 3°C for 1 hour, .500 inch mandrel, .375 lb., 2.5 kV dielectric test -65 ± 2°C for 4 hours, .500 inch mandrel, 1.00 lb., 2.5 kV dielectric test 200 ± 3°C for 6 hours, .125 inch (maximum) in 12 inches 5000 megohms for 1000 ft. (minimum) LOW TEMPERATURE COLD BEND SHIELD AWG 38, Nickel-Coated Oxygen Free High Conductivity Copper .109 SHRINKAGE INSULATION RESISTANCE INSULATION (DIELECTRIC) TENSILE STRENGTH ELONGATION INSULATION FLAWS SPARK TEST IMPULSE TEST 5000 lbf/in² (minimum) 50% (minimum) 3000 volts (rms) 8.0 kV (peak) FINISHED CABLE (Test Procedures per NEMA WC27500) JACKET Radiation-Crosslinked, Modified ETFE .125 (nominal) .136 (maximum) BLOCKING LOW TEMPERATURE COLD BEND CROSSLINKED VERIFICATION FLAMMABILITY (Method B per Spec. 1200) SHIELD COVERAGE JACKET FLAWS SPARK TEST IMPULSE TEST VOLTAGE WITHSTAND (DIELECTRIC) JACKET THICKNESS JACKET TENSILE STRENGTH ELONGATION 200°C for 6 hours -55 ± 5°C for 4 hours 6.0 inch mandrel 300 ± 5°C for 6 hours, 6.0 inch mandrel 3 seconds (maximum); 3.0 inches (maximum), no flaming of facial tissue 90% (minimum) 1000 volts (rms) 6.0 kV (peak) 1500 volts (rms) .008 inch (nominal) 5000 lbf/in² (minimum) 50% (minimum) Outer jacket color will be white (designated by a "-9" appended to the part number, e.g. EPD6314-24-9) unless otherwise specified. Designate outer jacket color with a dash number in accordance with MIL-STD-681. Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. WEIGHT 14.8 lbs/1000 ft. (maximum) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. R Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 1-800-227-8816 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCE DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.