1934315-1

Z-PACK TinMan High Speed, High Density Backplane Connector Introduction Product Facts ■ 10+ Gbps performance ■ 100 ohm Impedance for Differential Pair configuration ■ 5 pair version offers 26 pairs/10mm [66 differential pairs/inch] fitting within a 25.40 [1.00] card slot pitch ■ 4 pair version offers 21 pairs/10mm [53 differential pairs/inch] fitting within a 20.30 [.800] card slot pitch ■ 3 pair version offering 16 pairs/10mm [40 differential pairs/inch] fitting within a 16.25 [.625] card slot pitch ■ Right angle pin headers (coplanar) in 3 pair, 4 pair, and 5 pair versions ■ Reliable, redundant contact design on every signal contact ■ Modular system offered in various column versions ■ Meets Industry reliability requirements of Bellcore/ Telcordia ■ Sequencing for ground and signal contacts ■ RoHS Compliant Future Product Extensions ■ Vertical receptacles ■ High speed cable assemblies and hardware The Z-PACK TinMan backplane connector family is a cost-effective solution for customers searching for a high density, high performance backplane interconnect system. The Z-PACK TinMan connector design follows proven industry backplane convention by offering a fully protected right-angle receptacle for use on daughtercards where handling damage can be a concern when mating to a vertical male header. This connector permits field repairability at either the module or single pin levels. Industry Applications Technical Documents Ideally designed for cost pressured, high signal density applications requiring interconnection between two printed circuit boards, such as those typically found in server, storage, switch, router, and similar applications. The Z-PACK TinMan connector product family is suited to meet the demands of today’s modular system designs by offering a variety of configurations. The product family includes configurations to fit 20.32 [.800] and 25.40 [1.00] card slot spacing. Product Specification 108-2303 Application Specification 114-13202 Routing Guide Report #27GC001-1 Ground contacts positioned within each column of the connector, combined with unique contact lead frame arrangements, enable the Z-PACK TinMan connector to achieve low crosstalk and high through-put performance levels. Reliability is provided with a dual point of contact mating interface and compliant pin interface to the printed circuit board. Material and Finish Signal Contact — High Strength Copper Alloy Ground Contact — High Strength Copper Alloy Housing — Liquid Crystal Polymer Platings — Telcordia compliant interface, Nickel underplate Compliant Pin Plating — RoHS Compliant Ratings Temperature Range — -65°C to +90°C Current Rating — 0.5 A/contact @ < 30°C T-Rise Durability — 200 cycles Dielectric Withstanding Voltage — 560 VAC Operating Voltage — 250 VAC max. Signal Integrity Characteristic Impedance — Differential @ 100 ohms ±10% Crosstalk — Multi-pair differential crosstalk: 2.1% @ 50ps Insertion Loss — -2 dB @ 10 GHz For additional information visit: http://www.tycoelectronics.com/zpacktinman 1 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Introduction (Continued) Need more information? Call Technical Support at the numbers listed below. Technical Support is staffed with specialists well versed in Tyco Electronics products. They can provide you with: ■ Technical support ■ Catalogs ■ Technical Documents ■ Product Samples ■ Authorized Distributor Locations Disclaimer While Tyco Electronics Corporation and its affiliates referenced herein (“Tyco Electronics”) have made every reasonable effort to ensure the accuracy of the information in this catalog, Tyco Electronics does not guarantee that it is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information contained herein at any time without notice. Tyco Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics’ only obligations are those in the Tyco Electronics Standard Terms and Conditions of Sale, and in no case will Tyco Electronics be responsible for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of its products. Users should independently evaluate the suitability of, and test each product for, their application. The dimensions, specifications, designs, construction, materials and processes in this catalog are for reference purposes only and are subject to change without notice. Please consult Tyco Electronics for the most current product information. The export of certain Tyco Electronics products is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec 2751, et seq.) or the Export Administration Act of 1979, as amended (Title 50, U.S.C., App. 2401 et seq.). Orders may be subject to export approval by the U.S. Government. Buyer must comply with all applicable export laws of all applicable jurisdictions. © 2005 and 2007 by Tyco Electronics Corporation. All International Rights Reserved. AMP, MULTI-BEAM XL, MULTIGIG RT, Z-PACK, Z-PACK TinMan and TE LOGO and Tyco Electronics are trademarks. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. Restriction on the use of Hazardous Substances (RoHS) At Tyco Electronics, we’re ready to support your RoHS requirements. We’ve assessed more than 1.5 million end items/components for RoHS compliance, and issued new part numbers where any change was required to eliminate the restricted materials. Part numbers in this catalog are identified as: RoHS Compliant — Part numbers in this catalog are RoHS Compliant, unless marked otherwise. These products comply with European Union Directive 2002/95/EC as amended 1 January 2006 that restricts the use of lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in certain electrical and electronic products sold into the EU as of 1 July 2006. NOTE: For purposes of this Catalog, included within the definition of RoHS Compliant are products that are clearly “Out of Scope” of the RoHS Directive such as hand tools and other non-electrical accessories. NOTE: Information regarding RoHS compliance is provided based on reasonable inquiry of our suppliers and represents our current actual knowledge based on the information provided by our suppliers. This information is subject to change. For latest compliance status, refer to our website referenced at right. Getting the Information You Need Our comprehensive on-line RoHS Customer Support Center provides a forum to answer your questions and support your RoHS needs. A RoHS FAQ (Frequently Asked Questions) is available with links to more detailed information. You can also submit RoHS questions and receive a response within 24 hours during a normal work week. The Support Center also provides: ■ Cross-Reference from Non-compliant to Compliant Products ■ Ability to browse RoHS Compliant Products in our on-line catalog ■ Downloadable Technical Data Customer Information Presentation ■ More detailed information regarding the definitions used above ■ So whatever your questions when it comes to RoHS, we’ve got the answers at www.tycoelectronics.com/leadfree RoHS Customer Support Center 2 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Introduction (Continued) Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 Pair Right Angle Receptacle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Pair Right Angle Receptacle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 Pair Right Angle Receptacle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Pair Vertical Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Pair Vertical Header Assemblies — Left End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Pair Vertical Header Assemblies — Right End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Pair Vertical Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 Pair Vertical Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4 Pair Vertical Header Assemblies — Left End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4 Pair Vertical Header Assemblies — Right End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4 Pair Vertical Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3 Pair Vertical Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3 Pair Vertical Header Assemblies — Left End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3 Pair Vertical Header Assemblies — Right End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3 Pair Vertical Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5 Pair Right Angle Pin Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5 Pair Right Angle Pin Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . 22 4 Pair Right Angle Pin Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4 Pair Right Angle Pin Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . 24 3 Pair Right Angle Pin Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 3 Pair Right Angle Pin Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . 26 Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview . . . . . . . . . . . . . . . . . . . 27-29 6 Pair Mid-Plane Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-32 4 Pair Mid-Plane Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-35 Z-PACK TinMan Product Mating Sequence Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Z-PACK MAX Part Number to Z-PACK TinMan Part Number Cross-Reference . . . . . . 37, 38 Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Introduction (Continued) Noise Table ■ Victim Pair Maximum, multiple source crosstalk AB9 BC8 DE9 EF8 GH9 HI8 JG9 KL8 MN9 NO8 Total Peak Receiver Noise for Recommended Pin-Out 0.8% 1.6% 1.9% 1.9% 2.0% 2.0% 2.0% 2.1% 1.7% 0.8% Note: Data includes PCB vias of both backplane and daughtercard connectors. Single mated connector pair 50 ps (20-80%) edge rate Insertion Loss Plot 4 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Introduction (Continued) Representative Eye Pattern ■ 10.0 Gbps data rate ■ 27-1 PRBS ■ Unequalized Signal Customer Connector Evaluation Kit ■ Connector characterization ■ Available for loan — contact your local Tyco Electronics Sales Engineer ■ Time and frequency domain testable ■ Testable to 18+ GHz (25+ Gb/s) ■ Multiple calibration options ■ Convenient SMA interface Customer System Evaluation Kit ■ System characterization ■ Available for loan — contact your local Tyco Electronics Sales Engineer ■ Time and frequency domain testable ■ Testable to 18+ GHz (25+ Gb/s) ■ Multiple system lengths ■ Convenient SMA interface 5 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Right Angle Receptacle Assemblies Column Dimension A B 15.35 13.30 .604 .524 28.50 30.55 1.122 1.203 Part Number 8 1934218-1 16 1934221-1 Application Tooling Mates With * 1934269-1,(R) 1934272-1,(L) 1934273-1, 1934271-1, 1934349-1, 1934350-1 1934331-1, 1934334-1, 1934333-1, 1934332-1, 1934347-1, 1934348-1 * * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 31.81 ± 0.05 [1.252 ± .002] 1.90 Ref. [.075] 24.40 ± 0.10 [.961 ± .004] 19.50 [.768] 22.30 ± 0.08 [.878 ± .003] 1.40 Ref. [.055] 2.20 Ref. [.087] 1.40 Ref. [.055] Row A Row A 9.30 Ref. [.366] 1.70 Ref. [.067] 11.00 Ref. [.433] 19.60 Ref. [.772] Finished Hole Size and Plated Thru Holes* Connector Outline -XRow O Row N Row M Row L Row K Row J Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.21 Ref. [.048] 1.40 Typ. [.055] 19.60 Ref. [.772] 1.50 Max. [.059] 8 1 -YBSC 1.90 Typ. [.075] 1.25 Ref. [.049] 0.80 Ref. [.031] BSC B Recommended PC Board Layout Daughterboard Component Side Shown * Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 6 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Right Angle Receptacle Assemblies Column Part Number 8 1934222-1 16 1934225-1 Dimension A B 15.35 13.30 .604 .524 28.50 30.55 1.122 1.203 Application Tooling Mates With * 1934226-1, 1934304-1, 1934303-1, 1934306-1, 1934225-1, 1934354-1, 1934315-1, 1934318-1, 1934317-1, 1934316-1, 1934351-1, 1934352-1, * * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. 27.61 ± 0.05 [1.087 ± .002] A 1.90 Ref. [.075] 18.10 ± 0.08 [.713 ± .003] 15.30 Ref. [.602] 1.40 Ref. [.055] 20.20 ± 0.10 [.795 ± .004] Row A Row A 2.20 Ref. [.087] 1.70 Ref. [.067] 9.30 Ref. [.366] 1.40 Ref. [.055] 15.40 Ref. [.606] 11.00 Ref. [.433] Finished Hole Size and Plated Thru Holes* Connector Outline -X- Row L Row K Row J Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.21 Ref. [.048] 1.40 Typ. [.055] 15.40 Ref. [.606] 1.50 Max. [.059] 8 1 -Y- 1.25 Ref. [.049] BSC BSC 1.90 Typ. [.075] 0.80 Ref. [.031] B Recommended PC Board Layout Daughterboard Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 7 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Right Angle Receptacle Assemblies Dimension A B 15.35 13.30 .604 .524 17.10 19.15 .673 .754 28.50 30.55 1.122 1.203 Part Number Column 8 1934226-1 10 1934228-1 16 1934229-1 Application Tooling Mates With * 1934299-1, 1934300-1, 1934301-1, 1934302-1, 1934359-1, 1934360-1, 1934339-1, 1934341-1, 1934340-1, 1934342-1, 1934357-1, 1934358-1, 1934339-1, 1934340-1, 1934345-1, 1934346-1, 1934355-1, 1934356-1, * * * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. 23.41 ± 0.05 [.922 ± .002] A 1.90 Ref. [.075] 13.90 ± 0.08 [.547 ± .003] 11.10 Ref. [.437] 16.00 ± 0.10 [.630 ± .004] Row A 1.40 Ref. [.055] 2.20 Ref. [.087] Row A 1.70 Ref. [.067] 9.30 Ref. [.366] 1.40 Ref. [.055] 11.20 Ref. [.441] 11.00 Ref. [.433] Finished Hole Size and Plated Thru Holes* Connector Outline -X- 1.21 Ref. [.048] Row I Row H Row G Row F Row E Row D Row C Row B Row A 11.20 1.40 Ref. Typ. [.441] [.055] 1.50 Max. [.059] -Y1.25 Ref. [.049] BSC BSC 1.90 Typ. [.075] 0.80 Ref. [.031] B Recommended PC Board Layout Daughterboard Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] * Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 8 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Vertical Header Assemblies Column Part Number 8 1934269-1 16 1934331-1 Dimension A B 15.35 13.30 .604 .524 28.50 30.55 1.122 1.203 Application Tooling* Mates With 1-1804791-1 1934218-1 1-1804791-2 1934221-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 1.90 Ref. [.075] 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 1.425 Ref. [.056] 2.40 Ref. [.094] Row A 1.40 Ref. [.055] 1.40 Ref. [.055] 24.40 ± 0.10 [.961 ± .004] 22.60 ± 0.08 [.890 ± .003] 2.80 ± 0.05 [.110 ± .002] 2.38 Ref. [.094] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L Row M Row N Row O 2.40 Ref. [.094] 1.40 Typ. [.055] 19.60 Ref. [.772] 2.40 Ref. [.094] 1.90 Typ. [.075] 1.425 Ref. [.056] .625 Ref. [.025] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 9 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Vertical Header Assemblies — Left End Wall Column Part Number 8 1934272-1 16 1934333-1 Dimension A B 16.30 13.30 .642 .524 28.50 31.50 1.122 1.240 Application Tooling* Mates With 1-1804791-1 1934218-1 1-1804791-2 1934221-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 1.90 Ref. [.075] 2.40 Ref. [.094] 1.40 Ref. [.055] 24.40 ± 0.10 [.961 ± .004] 22.60 ± 0.08 [.890 ± .003] 1.40 Ref. [.055] Row A 2.80 ± 0.05 [.110 ± .002] 2.38 Ref. [.094] 11.50 ± 0.10 [.453 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L Row M Row N Row O 2.40 Ref. [.094] 1.40 Typ. [.055] 1.90 Typ. [.075] 0.63 Ref. [.025] 19.60 Ref. [.772] 2.40 Ref. [.094] 2.38 Ref. [.094] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 10 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Vertical Header Assemblies — Right End Wall Column Part Number 8 1934273-1 16 1934334-1 Dimension A B 17.00 13.30 .669 .524 28.50 32.20 1.122 1.268 Application Tooling* Mates With 1-1804791-1 1934218-1 1-1804791-2 1934221-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 1.90 Ref. [.075] 2.40 Ref. [.094] 1.40 Ref. [.055] 24.40 ± 0.10 [.961 ± .004] 22.60 ± 0.08 [.890 ± .003] 1.40 Ref. [.055] Row A 2.80 ± 0.05 [.110 ± .002] 2.38 Ref. [.094] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L Row M Row N Row O 2.40 Ref. [.094] 1.40 Typ. [.055] 1.90 Typ. [.075] 2.27 Ref. [.089] 19.60 Ref. [.772] 2.40 Ref. [.094] 1.425 Ref. [.056] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 11 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Vertical Header Assemblies — Double End Walls Column Part Number 8 1934271-1 16 1934332-1 Dimension A B 17.95 13.30 .707 .524 28.50 33.15 1.122 1.305 Application Tooling* Mates With 1-1804791-1 1934218-1 1-1804791-2 1934221-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 1.90 Ref. [.075] 2.40 Ref. [.094] Row A 1.40 Ref. [.055] 1.40 Ref. [.055] 24.40 ± 0.10 [.961 ± .004] 22.60 ± 0.08 [.890 ± .003] 2.80 ± 0.05 [.110 ± .002] 2.38 Ref. [.094] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L Row M Row N Row O 2.40 Ref. [.094] 1.40 Typ. [.055] 1.90 Typ. [.075] 2.275 Ref. [.089] 19.60 Ref. [.772] 2.40 Ref. [.094] 2.375 Ref. [.093] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 12 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Vertical Header Assemblies Column Part Number 8 1934305-1 16 1934315-1 Dimension A B 15.35 13.30 .604 .524 28.50 30.55 1.122 1.202 Application Tooling* Mates With 1-1804790-1 1934222-1 1-1804790-3 1934225-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 1.425 Ref. [.056] 2.40 Ref. [.094] Row A 1.40 Ref. [.055] 1.40 Ref. [.055] 0.10 20.20 +– 0.55 + .004 [.795 – .022 ] 0.08 18.40 +– 0.20 + .003 [.724 – .008 ] 2.80 ± 0.05 [.110 ± .002] 1.90 Ref. [.075] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L 2.40 Ref. [.094] 1.40 Typ. [.055] 15.40 Ref. [.606] 2.40 Ref. [.094] 1.90 Typ. [.075] 1.425 Ref. [.056] .625 Ref. [.025] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 13 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Vertical Header Assemblies — Left End Wall Column Part Number 8 1934303-1 16 1934317-1 Dimension A B 17.00 13.30 .669 .524 28.50 31.50 1.122 1.240 Application Tooling* Mates With 1-1804790-1 1934222-1 1-1804790-3 1934225-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 2.375 Ref. [.094] 2.40 Ref. [.094] 1.40 Ref. [.055] 0.10 20.20 +– 0.55 + .004 [.795 – .022 ] 0.08 18.40 +– 0.20 + .003 [.724 – .008 ] Row A 1.40 Ref. [.055] 2.80 ± 0.05 [.110 ± .002] 1.90 Ref. [.075] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L 2.40 Ref. [.094] 1.40 Typ. [.055] 15.40 Ref. [.606] 2.40 Ref. [.094] 1.90 Typ. [.075] 2.375 Ref. [.094] .625 Ref. [.025] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 14 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Vertical Header Assemblies — Right End Wall Column Part Number 8 1934304-1 16 1934318-1 Dimension A B 16.30 13.30 .642 .524 28.50 32.20 1.122 1.268 Application Tooling* Mates With 1-1804790-1 1934222-1 1-1804790-3 1934225-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 1.425 Ref. [.056] 2.40 Ref. [.094] 1.40 Ref. [.055] 0.10 20.20 +– 0.55 + .004 [.795 – .022 ] 0.08 18.40 +– 0.20 + .003 [.724 – .008 ] Row A 1.40 Ref. [.055] 1.90 Ref. [.075] 2.80 ± 0.05 [.110 ± .002] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L 2.40 Ref. [.094] 1.40 Typ. [.055] 15.40 Ref. [.606] 2.40 Ref. [.094] 1.90 Typ. [.075] 1.425 Ref. [.056] 2.275 Ref. [.090] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 15 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Vertical Header Assemblies — Double End Walls Column Part Number 8 1934306-1 16 1934316-1 Dimension A B 17.95 13.30 .707 .524 28.50 33.15 1.122 1.305 Application Tooling* Mates With 1-1804790-1 1934222-1 1-1804790-3 1934225-1 * Reference Application Specification 114-13202. 4.50 ± 0.15 [.177 ± .006] A 2.50 Ref. [.098] 6.00 ± 0.15 [.236 ± .006] 2.375 Ref. [.094] 2.40 Ref. [.094] Row A 1.40 Ref. [.055] 1.40 Ref. [.055] 0.10 20.20 +– 0.55 + .004 [.795 – .022 ] 0.08 18.40 +– 0.20 + .003 [.724 – .008 ] 2.80 ± 0.05 [.110 ± .002] 1.90 Ref. [.075] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline BSC -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I Row J Row K Row L 2.40 Ref. [.094] 1.40 Typ. [.055] 15.40 Ref. [.606] 2.40 Ref. [.094] 1.90 Typ. [.075] 2.375 Ref. [.094] 2.275 Ref. [.090] BSC B -X- Recommended PC Board Layout Backplane Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 16 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Vertical Header Assemblies Column Part Number 8 1934299-1 10 1934339-1 16 1934343-1 Dimension A B 15.53 13.30 .611 .524 17.10 19.15 .673 .754 28.50 30.55 1.122 1.203 Application Tooling* Mates With 1-1901457-1 1934226-1 1-1901457-2 1934228-1 1-1901457-3 1934229-1 * Reference Application Specification 114-13202. A 1.425 Ref. [.056] Row A 1.40 Ref. [.055] 2.50 Ref. [.098] 2.40 Ref. [.094] 0.10 16.00 +– 0.55 + .004 [.630 – .022 ] 1.40 Typ. [.055] Ref. 0.08 14.20 +– 0.20 + .003 [.559 – .008 ] 4.50 ± 0.15 [.177 ± .006] 1.90 Ref. [.075] 2.80 ± 0.05 [.110 ± .002] 6.00 ± 0.15 [.236 ± .006] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* -X- Connector Outline 2.40 Ref. BSC [.094] -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I 1.40 Typ. [.055] 1.90 Typ. [.075] 0.625 Ref. [.025] B 11.20 Ref. [.441] 2.40 Ref. [.094] 1.425 Ref. [.056] BSC Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 17 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Vertical Header Assemblies — Left End Wall Column Part Number 8 1934300-1 10 1934340-1 16 1934344-1 Dimension A B 16.30 13.30 .642 .524 17.10 20.10 .673 .791 28.50 31.50 1.122 1.240 Application Tooling* Mates With 1-1901457-1 1934226-1 1-1901457-2 1934228-1 1-1901457-3 1934229-1 * Reference Application Specification 114-13202. A 2.375 Ref. [.094] 2.50 Ref. [.098] 2.40 Ref. [.094] 0.10 16.00 +– 0.55 + .004 [.630 – .022 ] 1.40 Typ. [.055] Ref. 0.08 14.20 +– 0.20 + .003 [.559 – .008 ] Row A 1.40 Ref. [.055] 1.90 Ref. [.075] 4.50 ± 0.15 [.177 ± .006] 2.80 ± 0.05 [.110 ± .002] 6.00 ± 0.15 [.236 ± .006] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* -X- Connector Outline 2.40 Ref. BSC [.094] -Y- Row A Row B Row C Row D Row E Row F Row G Row H Row I 0.625 Ref. [.025] 1.40 Typ. [.055] 1.90 Typ. [.075] B 11.20 Ref. [.441] 2.40 Ref. [.094] 2.375 Ref. [.094] BSC Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 18 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Vertical Header Assemblies — Right End Wall Column Part Number 8 1934301-1 10 1934341-1 16 1934345-1 Dimension A B 17.00 13.30 .669 .524 17.10 20.08 .673 .791 28.50 32.20 1.122 1.268 Application Tooling* Mates With 1-1901457-1 1934226-1 1-1901457-2 1934228-1 1-1901457-3 1934229-1 * Reference Application Specification 114-13202. A 1.425 Ref. [.056] 2.50 Ref. [.098] 0.10 16.00 +– 0.55 + .004 [.630 – .022 ] 2.40 Ref. [.094] 1.40 Typ. [.055] Ref. 0.08 14.20 +– 0.20 + .003 [.559 – .008 ] Row A 1.40 Ref. [.055] 1.90 Ref. [.075] 4.50 ± 0.15 [.177 ± .006] 2.80 ± 0.05 [.110 ± .002] 6.00 ± 0.15 [.236 ± .006] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline 2.40 Ref. BSC [.094] -X- -YRow A Row B Row C Row D Row E Row F Row G Row H Row I 2.275 Ref. [.090] 1.40 Typ. [.055] 1.90 Typ. [.075] B 11.20 Ref. [.441] 2.40 Ref. [.094] 1.425 Ref. [.056] BSC Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 19 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Vertical Header Assemblies — Double End Walls Column Part Number 8 1934302-1 10 1934342-1 16 1934346-1 Dimension A B 17.95 13.30 .707 .524 17.10 21.75 .673 .856 28.50 33.15 1.122 1.305 Application Tooling* Mates With 1-1901457-1 1934226-1 1-1901457-2 1934228-1 1-1901457-3 1934229-1 * Reference Application Specification 114-13202. A 2.375 Ref. [.094] Row A 1.40 Ref. [.055] 2.50 Ref. [.098] 0.10 16.00 +– 0.55 + .004 [.630 – .022 ] 1.40 Typ. [.055] Ref. 0.08 14.20 +– 0.20 + .003 [.559 – .008 ] 4.50 ± 0.15 [.177 ± .006] 1.90 Ref. [.075] 2.40 Ref. [.094] 2.80 ± 0.05 [.110 ± .002] 6.00 ± 0.15 [.236 ± .006] 11.80 ± 0.10 [.465 ± .004] Finished Hole Size and Plated Thru Holes* Connector Outline 2.40 Ref. BSC [.094] -X- -YRow A Row B Row C Row D Row E Row F Row G Row H Row I 2.275 Ref. [.090] 1.40 Typ. [.055] 1.90 Typ. [.075] B 11.20 Ref. [.441] 2.40 Ref. [.094] 2.375 Ref. [.094] BSC Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 20 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Right Angle Pin Header Assemblies Column Part Number 8 1934349-1 16 1934347-1 Dimension A B 15.35 13.30 .604 .524 28.50 30.55 1.122 1.203 Application Tooling Mates With * 1934218-1 * 1934221-1 * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 27.61 ± 0.05 [1.087 ± .002] 1.90 Ref. [.075] 0.625 Ref. [.025] 0.10 24.40 +– 0.55 + .004 [.961 – .022 ] 19.50 Ref. [.768] 0.08 22.60 +– 0.20 + .003 [.890 – .008 ] Row A 2.20 ± 0.15 [.087 ± .006] 1.40 Ref. [.055] Row A 1.40 Ref. [.055] 4.50 Ref. [.177] 6.00 Ref. [.236] 1.70 Ref. [.067] 19.60 Ref. [.772] 9.00 ± 0.13 [.354 ± .005] 6.80 Ref. [.268] Finished Hole Size and Plated Thru Holes* Connector Outline 1.21 Ref. [.048] -XRow O Row N Row M Row L Row K Row J Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.40 Typ. [.055] 19.60 Ref. [.772] 1.50 Max. [.059] 1 8 1.95 Ref. [.077] 1.90 Typ. [.075] 0.90 Ref. [.035] -Y0.90 Ref. [.035] BSC 15.80 Ref. [.622] 1.15 Ref. [.045] BSC B Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 21 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 5 Pair Right Angle Pin Header Assemblies — Double End Walls Column Part Number 8 1934350-1 16 1934348-1 Dimension A B 18.05 13.30 .711 .524 28.50 33.25 1.122 1.309 Application Tooling Mates With * 1934218-1 * 1934221-1 * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 27.61 ± 0.05 [1.087 ± .002] 1.90 Ref. [.075] 2.375 Ref. [.094] 24.40 +– 19.50 Ref. [.768] + [.961 – 0.08 22.60 +– 0.20 .003 [.890 +– .008 ] Row A 2.20 ± 0.15 [.087 ± .006] 1.40 Ref. [.055] Row A 1.40 Ref. [.055] 4.50 Ref. [.177] 6.00 Ref. [.236] 1.70 Ref. [.067] 19.60 Ref. [.772] 6.80 Ref. [.268] 9.00 ± 0.13 [.354 ± .005] Finished Hole Size and Plated Thru Holes* Connector Outline 1.21 Ref. [.048] -XRow O Row N Row M Row L Row K Row J Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.40 Typ. [.055] 19.60 Ref. [.772] 1.50 Max. [.059] 1 8 1.95 Ref. [.077] 0.90 Ref. [.035] 2.10 Ref. [.083] BSC 1.90 Typ. [.075] B -Y0.90 Ref. [.035] 2.65 Ref. [.104] BSC 15.80 Ref. [.622] Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 22 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 ] Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Right Angle Pin Header Assemblies Column Part Number 8 1934353-1 16 1934351-1 Dimension A B 15.35 13.30 .604 .524 28.50 30.55 1.122 1.203 Application Tooling Mates With * 1934222-1 * 1934225-1 * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 24.00 ± 0.05 [.945 ± .002] 1.90 Ref. [.075] 0.625 Ref. [.025] 0.10 20.20 +– 0.55 + .004 [.795 – .022 ] 15.30 Ref. [.602] 0.08 18.40 +– 0.20 + .003 [.724 – .008 ] Row A 2.20 ± 0.15 [.087 ± .006] 1.40 Ref. [.055] Row A 1.40 Ref. [.055] 4.50 Ref. [.177] 6.00 Ref. [.236] 1.70 Ref. [.067] 15.40 Ref. [.606] 6.80 Ref. [.268] 9.00 ± 0.13 [.354 ± .005] Finished Hole Size and Plated Thru Holes* Connector Outline -X1.80 Ref. [.071] Row L Row K Row J Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.40 Typ. [.055] 15.40 Ref. [.606] 1.50 Max. [.059] 1 8 1.95 Ref. [.077] 0.90 Ref. [.035] 1.90 Typ. [.075] -Y0.90 Ref. [.035] BSC 15.80 Ref. [.622] 1.15 Ref. [.045] BSC B Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 23 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Right Angle Pin Header Assemblies — Double End Walls Column Part Number 8 1934354-1 16 1934352-1 Dimension A B 18.05 13.30 .711 .524 28.50 33.25 1.122 1.309 Application Tooling Mates With * 1934222-1 * 1934225-1 * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 24.00 ± 0.05 [.945 ± .002] 1.90 Ref. [.075] 2.375 Ref. [.094] 0.10 20.20 +– 0.55 + .004 [.795 – .022 ] 15.30 Ref. [.602] + 0.08 18.40 – 0.20 + .003 [.724 – .008 ] Row A 2.20 ± 0.15 [.087 ± .006] 1.40 Ref. [.055] Row A 1.40 Ref. [.055] 4.50 Ref. [.177] 6.00 Ref. [.236] 1.70 Ref. [.067] 15.40 Ref. [.606] 9.00 ± 0.13 [.354 ± .005] 6.80 Ref. [.268] Finished Hole Size and Plated Thru Holes* Connector Outline -X1.80 Ref. [.071] Row L Row K Row J Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.40 Typ. [.055] 15.40 Ref. [.606] 1.50 Max. [.059] 1 8 1.95 Ref. [.077] 0.90 Ref. [.035] 1.90 Typ. [.075] 2.10 Ref. [.083] -Y0.90 Ref. [.035] BSC 15.80 Ref. [.622] 2.65 Ref. [.104] BSC B Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 24 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Right Angle Pin Header Assemblies Column Part Number 8 1934359-1 10 1934357-1 16 1934355-1 Dimension A B 15.35 13.30 .604 .524 17.10 19.15 .673 .754 28.50 30.55 1.122 1.203 Application Tooling Mates With * 1934226-1 * 1934228-1 * 1934229-1 * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 19.80 ± 0.05 [.780 ± .002] 1.90 Ref. [.075] 0.625 Ref. [.025] 0.10 16.00 +– 0.55 + .004 [.630 – .022 ] 11.10 Ref. [.437] 1.40 Ref. [.055] 0.08 14.20 +– 0.20 .003 [.559 +– .008 ] 2.20 ± 0.15 [.087 ± .006] Row A Row A 1.40 Ref. [.055] 4.50 Ref. [.177] 6.00 Ref. [.236] 1.70 Ref. [.067] 11.20 Ref. [.441] 6.80 Ref. [.268] 9.00 ± 0.13 [.354 ± .005] Finished Hole Size and Plated Thru Holes* -X- Connector Outline 1.80 Ref. [.071] Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.40 Typ. [.055] 11.20 Ref. [.441] 1.50 Max. [.059] 1 8 1.95 Ref. [.077] 0.90 Ref. [.035] 1.15 Ref. [.045] BSC 1.90 Typ. [.075] -Y0.90 Ref. [.035] BSC 15.80 Ref. [.622] B Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 25 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 3 Pair Right Angle Pin Header Assemblies — Double End Walls Column Part Number 8 1934360-1 10 1934358-1 16 1934356-1 Dimension A B 18.05 13.30 .711 .524 17.10 21.85 .673 .860 28.50 33.25 1.122 1.309 Application Tooling Mates With * 1934226-1 * 1934228-1 * 19343229-1 * Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202. A 1.90 Ref. [.075] 2.375 Ref. [.094] 19.80 ± 0.05 [.780 ± .002] 0.10 16.00 +– 0.55 .004 [.630 +– .022 ] 11.10 Ref. [.437] 1.40 Ref. [.055] Row A 2.20 ± 0.15 [.087 ± .006] 1.40 Ref. [.055] Row A 0.08 14.20 +– 0.20 + .003 [.559 – .008 ] 4.50 Ref. [.177] 6.00 Ref. [.236] 1.70 Ref. [.067] 11.20 Ref. [.441] 6.80 Ref. [.268] 9.00 ± 0.13 [.354 ± .005] Finished Hole Size and Plated Thru Holes* -X- Connector Outline 1.80 Ref. [.071] Row I Row H Row G Row F Row E Row D Row C Row B Row A 1.40 Typ. 11.20 [.055] Ref. [.441] 1.50 Max. [.059] 1 8 1.95 Ref. [.077] 1.90 Typ. [.075] 0.90 Ref. [.035] 2.10 Ref. [.083] BSC -YBSC 0.90 Ref. [.035] 2.65 Ref. [.104] 15.80 Ref. [.622] B Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC001-1. * * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 26 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview Product Facts ■ Scalable to 25 Gbps ■ 100 ohm impedance for differential pair configuration ■ Very low noise ■ Outstanding insertion loss through 2 connectors and vias ■ Skewless differential pair in a 2-connector system ■ Utilizes the same header and receptacle part on both sides of the mid-plane ■ Compatible with standard Z-PACK TinMan connectors and accessories ■ 4 pair x 4 pair and 6 pair x 6 pair modules available ■ Reliable, redundant contact design on all contacts ■ Reliable press-fit style termination to PCB ■ RoHS compliant Applications The Z-PACK TinMan Mid-plane (orthogonal) connector is ideally designed for very demanding applications involving data rates in excess of 10 Gbps with many interconnections required. Such applications would include the following Telecom/Datacom equipment: ■ Switches ■ Servers ■ Routers ■ Storage The Z-PACK TinMan midplane (orthogonal) connector is an extension of the Z-PACK TinMan connector product line, which includes perpendicular and coplanar interconnect solutions in 3 pair, 4 pair, and 5 pair versions. This connector system is commonly referred to as an orthogonal connector system due to the orthogonal (perpendicular) orientation of the two system boards being connected on the front and rear side. It is built on the same technology and design approach as standard Z-PACK TinMan connectors with the same mating interface and leadframe geometry. Superior electrical performance is achieved for several reasons. The front board to For additional information visit: http://www.tycoelectronics.com/zpacktinman rear board connection through the mid-plane makes the plated through hole (PTH) part of the signal transmission path eliminating the detrimental effects of via stubs. This construction also eliminates the need to route all the high speed signal lines along the backplane minimizing signal loss and significantly improving signal throughput. The wide column spacing establishes a connector footprint with improved impedance and reduced electrical noise. The in-line footprint version also provides ease of trace routing with wide channels and a connector interface compatible with the orthogonal receptacle. This permits the use of the same daughtercard in both mid-plane and backplane configurations. The benefits are not limited to just signal integrity performance. The thinner midplane with fewer layers and significantly less complex routing is inherently less expensive. With trace routing typically limited to power distribution, low speed lines and potentially very few high speed links, the board can be fabricated from a cost effective material without the need to utilize techniques such as counter-boring or backdrilling. All of this permits the implementation of small to large scale full mesh interconnects with significantly reduced complexity at a lower cost and with improved signal integrity. 6x6 (36 signal pairs) 27 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview (Continued) Noise Table ■ VICTIM Maximum, multiple source crosstalk Technical Documents Product Specification 108-2303 Application Specification 114-13202 Routing Guide Report #27GC002 Material and Finish AB3 CD3 EF3 GH3 JK3 LM3 Total Peak Receiver Noise for Recommended Pin-Out 0.50% 1.00% 0.90% 0.80% 0.90% 0.60% Note: Data includes PCB vias of both backplane and daughtercard connectors. Single mated connector pair. 50 ps (20-80%) edge rate. Signal Contact — High Strength Copper Alloy Ground Contact — High Strength Copper Alloy Housing — Liquid Crystal Polymer Platings — Telcordia compliant interface, Nickel underplate Compliant Pin Plating — RoHS Compliant Ratings Temperature Range — -65°C to +90°C Current Rating — 0.5 A/contact @ < 30°C T-Rise Durability — 200 cycles Dielectric Withstanding Voltage — 560 VAC Operating Voltage — 250 VAC max. Signal Integrity Characteristic Impedance — Differential @ 100 ohms ±10% Crosstalk — Multi-pair differential crosstalk: 1.0% @ 50ps Insertion Loss — -2 dB @ 10 GHz Insertion Loss Plot 28 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview (Continued) Representative Eye Pattern ■ 10.0 Gbps data rate ■ 27 -1 PRBS ■ Unequalized Signal Customer Connector Evaluation Kit ■ Connector characterization ■ Available for loan — contact your local Tyco Electronics Sales Engineer ■ Time and frequency domain testable ■ Testable to 18+ GHz (25+ Gb/s) ■ Multiple calibration options ■ Convenient SMA interface Customer System Evaluation Kit ■ System characterization ■ Available for loan — contact your local Tyco Electronics Sales Engineer ■ Time and frequency domain testable ■ Testable to 18+ GHz (25+ Gb/s) ■ Multiple calibration options ■ Convenient SMA interface 29 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 6 Pair Mid-Plane Assemblies 6 Pair Right Angle Receptacle Assembly Part Number: 1934231-1 Custom tooling not required. Utilizes flat-rock insertion tooling. 30.00 ± 0.10 [1.181 ± .004] Reference Application Specification 114-13202 25.10 [.988] Ref. Mates with: 1934364-1, 1934363- 1 27.90 ± 0.08 [1.098 ± .003] Position A1 4.20 Ref. [.165] 1.80 Ref. [.071] 2.20 [.087] Ref. 1.40 Ref. [.055] 1.70 Ref. [.067] 21.60 Ref. [.850] 11.00 Ref. [.433] Finished Hole Size and Plated Thru Holes* 2.625 Ref. [.103] Connector Outline 1.475 Ref. [.058] 1.21 Ref. [.048] Row M Row L Row K Row J Row H Row G 32.40 Ref. [1.276] Row F Row E Row D Row C 1.80 Typ. [.071] Row B Row A 12.50 Ref. [.492] 4.20 Typ. [.165] 2.10 0.10 Typ. Ref. [.083] [.004] Surface of Mating Midplane 1.50 Max. [.059] 11.00 Ref. [.433] BSC -Y21.00 Ref. [.827] BSC -X- Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC002. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 30 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 6 Pair Mid-Plane Assemblies (Continued) 6 Pair Vertical Header Assembly Part Number: 1934364-1 27.50 ± 0.05 [1.083 ± .002] Insertion Tooling: Contact Tyco Electronics 11.80 ± 0.10 [.465 ± .004] Reference Application Specification 114-13202 Mates with: 1934231-1 0.10 30.00 +– 0.55 + .004 [1.181 – .022 ] 1.90 ± 0.20 Typ. [.075 ± .008] 4.40 ± 0.15 Typ. [.173 ± .006] 1.80 ± 0.20 Typ. [.071 ± .008] 6.00 ± 0.15 Typ. [.236 ± .006] 2.80 ± 0.05 [.110 ± .002] Finished Hole Size and Plated Thru Holes* Footprint shown for reference only. Contact Tyco Electronics engineering for details. 1 2 3 4 5 6 M L Connector Outline K J H G F E 25.20 Ref. [.992] D C B A FRONT 25.20 Ref. [.992] Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC002. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 31 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 6 Pair Mid-Plane Assemblies (Continued) 6 Pair Vertical Header Assembly — In Line Footprint Part Number: 1934363-1 27.50 ± 0.05 [1.083 ± .002] Insertion Tooling: Contact Tyco Electronics 11.80 ± 0.10 [.465 ± .004] Reference Application Specification 114-13202 Mates with: 1934231-1 0.10 30.00 +– 0.55 + .004 [1.181 – .022 ] 1.40 Ref. [.055] 2.40 Ref. [.094] 4.50 ± 0.15 Typ. [.177 ± .006] 6.00 ± 0.15 Typ. [.236 ± .006] 1.80 ± 0.20 [.071 ± .008] 2.80 ± 0.05 [.110 ± .002] Footprint shown for reference only. Contact Tyco Electronics engineering for details. Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC002. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 32 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Mid-Plane Assemblies 4 Pair Right Angle Receptacle Assembly Part Number: 1934230-1 Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202 21.60 ± 0.10 [.850 ± .004] Mates with: 1934362-1, 1934361-1 16.70 Ref. [.657] 19.50 ± 0.08 [.768 ± .003] Position A1 4.20 Ref. [.165] 2.20 Ref. [.087] 1.40 Ref. [.055] 1.80 Ref. [.071] 1.70 Ref. [.067] 21.60 Ref. [.850] 11.00 Ref. [.433] Finished Hole Size and Plated Thru Holes* 2.625 Ref. [.103] Connector Outline 1.475 Ref. [.058] 1.21 Ref. [.048] Row H Row G 21.60 Ref. [.850] Row F Row E Row D Row C 1.80 Typ. [.071] Row B Row A 0.10 Ref. [.004] 12.50 Ref. [.492] Surface of Mating Midplane 4.20 Typ. [.165] 2.10 Typ. [.083] 1.50 Max. [.059] 11.00 Ref. [.433] BSC -Y12.60 Ref. [.496] BSC -X- Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC002. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 33 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Mid-Plane Assemblies (Continued) 4 Pair Vertical Header Assembly Part Number: 1934362-1 Insertion Tooling: Contact Tyco Electronics 19.10 ± 0.05 [.752 ± .002] Reference Application Specification 114-13202 11.80 ± 0.10 [.465 ± .004] Mates with: 1934230-1 0.10 21.60 +– 0.55 + .004 [.850 – .022 ] 1.90 ± 0.20 Typ. [.075 ± .008] 4.40 ± 0.15 Typ. [.173 ± .006] 1.80 ± 0.20 Typ. [.071 ± .008] 6.00 ± 0.15 Typ. [.236 ± .006] 2.80 ± 0.05 [.110 ± .002] Finished Hole Size and Plated Thru Holes* 1 Footprint shown for reference only. Contact Tyco Electronics engineering for details. 2 3 4 H G Connector Outline F E 16.80 Ref. [.691] D C B A BSC FRONT 16.80 Ref. [.691] BSC Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC002. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 34 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector 4 Pair Mid-Plane Assemblies (Continued) 4 Pair Vertical Header Assembly — In Line Footprint Part Number: 1934361-1 Insertion Tooling: Contact Tyco Electronics Reference Application Specification 114-13202 19.10 ± 0.05 [.752 ± .002] 11.80 ± 0.10 [.465 ± .004] Mates with: 1934230-1 1.40 Ref. [.055] 0.10 21.60 +– 0.55 + .004 [.850 – .022 ] 1.80 ± 0.20 Typ. [.071 ± .008] 4.50 ± 0.15 Typ. [.177 ± .006] 6.00 ± 0.15 Typ. [.236 ± .006] 1 Footprint shown for reference only. Contact Tyco Electronics engineering for details. 2 2.40 Ref. [.094] 3 4 2.80 ± 0.05 [.110 ± .002] BSC Connector Outline H G F E 16.80 Ref. [.661] D C B A 12.60 Ref. [.496] BSC Recommended PC Board Layout Component Side Shown Note: For additional information on pcb routing guidelines, reference the Z-PACK TinMan Connector Routing Guide Report #27GC002. * Finished Hole Diameter = 0.46 ±0.05 [.018 ±.002] Drilled Hole Diameter = 0.55 ±0.02 [.022 ±.001] Copper Thickness = 0.038 ±0.013 [.0015 ±.0005] Tin-Lead Thickness = 0.008 ±0.004 [.0003 ±.0002] Finishes other than Tin-Lead, See Appl. Spec. 114-13202 35 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Z-PACK TinMan Product Mating Sequence Chart Fully Mated Product Family Dim. C Dim. A Fully Mated Z-PACK HM-Zd Product 1.50 .059 12.50 .492 Z-PACK HM-Zd Guide Hardware 3.00 .118 12.50 .492 Z-PACK TinMan Product 1.50 .059 12.50 .492 Z-PACK 2mm HM Product 1.50 .059 12.50 .492 MULTIGIG RT T1 Product 2.50 .098 12.50 .492 MULTIGIG RT T2 Product 2.25 .089 12.50 .492 MULTIGIG RT T3 Product 2.25 .089 12.50 .492 MULTIGIG RT Power Module 5.50 .217 12.50 .492 MULTIGIG RT Guide Hardware N/A 12.50 .492 Z-PACK HS3 Product 1.50 .059 12.50 .492 UPM 3.50 .138 12.50 .492 UPM Guide Hardware 5.75 .226 12.50 .492 MULTI-BEAM XL Right Angle Header to Vertical Receptacle MULTI-BEAM XL Right Angle Receptacle to Vertical Header 5.08 .200 3.81 .150 14.73 .580 13.21 .520 Reliable Mate Contact Ground Shield Signal Level 2 Signal Level 1 24.0 mm Pin 22.2 mm Pin Key Blocking Point Ground Pins Signal Level 2 Signal Level 1 Signal Level 3 Signal Level 2 Signal Level 1 Ground Signal Level 3 Signal Level 2 Signal Level 1 Ground Signal Level 3 Signal Level 2 Signal Level 1 Ground Signal Level 1 Power Level 3 Power Level 2 Power Level 1 Dim B. First Mate Reliable Last Break Mate 16.78 [.661] 17.55 [.691] 15.41 [.607] 15.85 [.624] 13.91 [.548] 14.35 [.565] 27.50 [1.083] 33.40 [1.315] 25.70 [1.012] 31.60 [1.244] N/A 22.03 [.867] 16.44 [.647] 17.13 [.674] 14.94 [.588] 15.63 [.615] N/A N/A 18.27 [.719] 18.84 [.742] 16.77 [.660] 17.34 [.683] 15.27 [.601] 15.84 [.624] 18.00 [.709] — 18.00 [.709] — 16.50 [.650] — 15.00 [.591] — 18.00 [.709] — 18.00 [.709] — 16.50 [.650] — 15.00 [.591] — 16.50 [.650] — 15.00 [.591] — 23.75 [.935] — 22.25 [.876] — 20.75 [.817] — Fully Mated Wipe Length 4.28 [.169] 2.91 [.115] 1.41 [.056] N/A N/A N/A 3.94 [.155] 2.44 [.096] N/A 5.77 [.227] 4.27 [.168] 2.77 [.109] 5.50 [.217] 5.50 [.217] 4.00 [.157] 2.50 [.098] 5.50 [.217] 5.50 [.217] 4.00 [.157] 2.50 [.098] 4.00 [.157] 2.50 [.098] 11.25 [.443] 9.75 [.384] 8.25 [.325] Guide Pin Key 33.25 [1.309] N/A 20.75 [.817] Guide ESD Contact 30.75 [1.211] — 18.25 [.719] Ground Signal Level 2 Signal Level 1 Power Level 3 Power Level 2 Power Level 1 Guide Pin Key Keyed Guide Pin Keyed Guide Pin PreMate Power — Level 1 PostMate Power — Level 2 PreMate Signal — Level 2 PostMate Signal — Level 3 PreMate Power — Level 1 PostMate Power — Level 2 PreMate Signal — Level 2 PostMate Signal — Level 3 17.08 [.672] 16.05 [.632] 14.55 [.573] 20.25 [.797] 18.65 [.734] 17.03 [.670] 31.39 [1.236] 31.39 [1.236] 35.23 [1.387] 17.60 [.693] 16.47 [.648] 14.97 [.589] 20.95 [.825] 19.35 [.762] 17.73 [.698] 36.16 [1.424] 36.16 [1.424] 40.00 [1.575] — 16.84 [.663] — 17.81 [.701] — 18.26 [.719] — 19.53 [.769] — 15.32 [.603] — 16.28 [.641] — 16.74 [.659] — 18.01 [.709] 4.78 [.188] 3.75 [.148] 2.25 [.089] 8.10 [.319] 6.50 [.256] 4.88 [.192] N/A N/A N/A 5.61 [.221] Min. 4.34 [.171] Min. 3.81 [.150] Min. 2.54 [.100] Min. 5.61 [.221] Min. 4.34 [.171] Min. 3.81 [.150] Min. 2.54 [.100] Min. 36 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Z-PACK MAX Connector to Z-PACK TinMan Connector Base Part Number Cross Reference* Z-PACK MAX Connector Base Part Number 1469659 1469660 1469680 1469680 1469681 1469687 1469693 1469702 1469702 1469703 1469703 1469706 1469707 1469716 1469717 1469735 1469737 1469753 1469754 1469755 1469755 1469756 1469768 1469769 1469774 1469775 1469784 1469785 1469786 1469787 1469788 1469789 1469793 1469795 1469807 1469809 1469827 1469828 1469829 1469831 1469853 1469854 1469867 1469867 1469871 1469874 1469935 1469945 1469945 1469946 1469949 1469950 1469950 1469951 1469955 1469960 Z-PACK TinMan Connector Base Part Number 1934218 1934269 1934272 1934273 1934271 1934315 1934225 1934303 1934304 1934317 1934318 1934306 1934316 1934305 1934222 1934349 1934350 1934331 1934221 1934333 1934334 1934332 1934305 1934222 1934311 1934224 1934362 1934230 1934364 1934231 1934311 1934224 1934353 1934354 1934339 1934228 1934339 1934228 1934299 1934226 1934335 1934227 1934340 1934341 1934357 1934358 1934342 1934300 1934301 1934302 1934343 1934344 1934345 1934346 1934229 1934335 Description Receptacle Assembly, 5 pair, Standard, 8 Column Header Assembly, Open Ended, 5 Pair 8 Column Header Assembly, Left Wall, 5 Pair 8 Column Header Assembly, Right Wall, 5 Pair 8 Column Header Assembly, Double Wall, 5 Pair 8 Column Header Assembly, Open Ended, 4 Pair 16 Column Receptacle Assembly, 4 pair, Standard, 16 Column Header Assembly, Left Wall, 4 Pair 8 Column Header Assembly, Right Wall, 4 Pair 8 Column Header Assembly, Left Wall, 4 Pair 16 Column Header Assembly, Right Wall, 4 Pair 16 Column Header Assembly, Double Wall, 4 Pair 8 Column Header Assembly, Double Wall, 4 Pair 16 Column Header Assembly, Open Ended, 4 Pair 8 Column Receptacle Assembly, 4 pair, Standard, 8 Column Right Angle Header Assembly, Open Ended, 5 Pair 8 Column Right Angle Header Assembly, Double Wall, 5 Pair 8 Column Header Assembly, Open Ended, 5 Pair 16 Column Receptacle Assembly, 5 pair, Standard, 16 Column Header Assembly, Left Wall, 5 Pair 16 Column Header Assembly, Right Wall, 5 Pair 16 Column Header Assembly, Double Wall, 5 Pair 16 Column Header Assembly, Open Ended, 4 Pair 8 Column Receptacle Assembly, 4 pair, Standard, 8 Column Header Assembly, Open Ended, 4 Pair 10 Column Receptacle Assembly, 4 pair, Standard, 10 Column 4x4 Orthogonal Offset Header Assembly, Double Wall Receptacle Assembly, 4x4, Orthogonal 6x6 Orthogonal Offset Header Assembly, Double Wall Receptacle Assembly, 6x6, Orthogonal Header Assembly, Open Ended, 4 Pair 10 Column Receptacle Assembly, 4 pair, Standard, 10 Column Right Angle Header Assembly, Open Ended, 4 Pair 8 Column Right Angle Header Assembly, Double Wall, 4 Pair 8 Column Header Assembly, Open Ended, 3 Pair 10 Column Receptacle Assembly, 3 pair, Standard, 10 Column Header Assembly, Open Ended, 3 Pair 10 Column Receptacle Assembly, 3 pair, Standard, 10 Column Header Assembly, Open Ended, 3 Pair 8 Column Receptacle Assembly, 3 pair, Standard, 8 Column Header Assembly, Open Ended, 3 Pair 6 Column Receptacle Assembly, 3 pair, Standard, 6 Column Header Assembly, Left Wall, 3 Pair 10 Column Header Assembly, Right Wall, 3 Pair 10 Column Right Angle Header Assembly, Open Ended, 3 Pair 10 Column Right Angle Header Assembly, Double Wall, 3 Pair 10 Column Header Assembly, Double Wall, 3 Pair 10 Column Header Assembly, Left Wall, 3 Pair 8 Column Header Assembly, Right Wall, 3 Pair 8 Column Header Assembly, Double Wall, 3 Pair 8 Column Header Assembly, Open Ended, 3 Pair 16 Column Header Assembly, Left Wall, 3 Pair 16 Column Header Assembly, Right Wall, 3 Pair 16 Column Header Assembly, Double Wall, 3 Pair 16 Column Receptacle Assembly, 3 pair, Standard, 16 Column Header Assembly, Open Ended, 3 Pair 6 Column *As announced on 6/20/07, Tyco Electronics now offers the Z-PACK TinMan product line as a form, fit and function replacement to the Z-PACK MAX product line. This chart will assist in finding the Z-PACK TinMan connector part number if you have a Z-PACK MAX connector part number. 37 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Z-PACK MAX Connector to Z-PACK TinMan Connector Base Part Number Cross Reference* (Continued) Z-PACK MAX Connector Base Part Number 1469961 1469961 1469962 1469966 1469974 1469977 1934007 1934008 1934008 1934009 1934010 1934018 1934021 1934026 1934029 1934034 1934037 1934106 1934106 1934107 1934121 1934122 1934127 1934136 1934137 1934137 1934141 1934165 1934171 1934194 1934208 1934210 1934210 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Z-PACK TinMan Connector Base Part Number 1934336 1934337 1934338 1934227 1934359 1934360 1934321 1934323 1934324 1934322 1934219 1934347 1934348 1934351 1934352 1934355 1934356 1934313 1934314 1934312 1934364 1934231 1934220 1934315 1934317 1934318 1934363 1934361 1934275 1934325 1934326 1934327 1934328 1934223 1934274 1934276 1934287 1934288 1934289 1934290 1934307 1934308 1934309 1934310 1934319 1934320 1934329 1934330 Description Header Assembly, Left Wall, 3 Pair 6 Column Header Assembly, Right Wall, 3 Pair 6 Column Header Assembly, Double Wall, 3 Pair 6 Column Receptacle Assembly, 3 pair, Standard, 6 Column Right Angle Header Assembly, Open Ended, 3 Pair 8 Column Right Angle Header Assembly, Double Wall, 3 Pair 8 Column Header Assembly, Open Ended, 5 Pair 6 Column Header Assembly, Left Wall, 5 Pair 6 Column Header Assembly, Right Wall, 5 Pair 6 Column Header Assembly, Double Wall, 5 Pair 6 Column Receptacle Assembly, 5 pair, Standard, 6 Column Right Angle Header Assembly, Open Ended, 5 Pair 16 Column Right Angle Header Assembly, Double Wall, 5 Pair 16 Column Right Angle Header Assembly, Open Ended, 4 Pair 16 Column Right Angle Header Assembly, Double Wall, 4 Pair 16 Column Right Angle Header Assembly, Open Ended, 3 Pair 16 Column Right Angle Header Assembly, Double Wall, 3 Pair 16 Column Header Assembly, Left Wall, 4 Pair 10 Column Header Assembly, Right Wall, 4 Pair 10 Column Header Assembly, Double Wall, 4 Pair 10 Column 6x6 Orthogonal Offset Header Assembly, Double Wall Receptacle Assembly, 6x6, Orthogonal Receptacle Assembly, 5 pair, Standard, 10 Column Header Assembly, Open Ended, 4 Pair 16 Column Header Assembly, Left Wall, 4 Pair 16 Column Header Assembly, Right Wall, 4 Pair 16 Column 6x6 Orthogonal In-Line Header Assembly, Double Wall 4x4 Orthogonal In-Line Header Assembly, Double Wall Receptacle Assembly, 4 pair, Standard, 14 Column Header Assembly, Open Ended, 5 Pair 10 Column Header Assembly, Double Wall, 5 Pair 10 Column Header Assembly, Left Wall, 5 Pair 10 Column Header Assembly, Right Wall, 5 Pair 10 Column Receptacle Assembly, 4 pair, Standard, 6 Column Header Assembly 5 Pair Open Ended 8 Column Notched Wall Receptacle Assembly, 5 pair, Standard, 14 Column Header Assembly, Open Ended, 5 Pair 14 Column Header Assembly, Open Ended, 4 Pair 14 Column Header Assembly, Double Wall, 5 Pair 14 Column Header Assembly, Double Wall, 4 Pair 14 Column Header Assembly, Open Ended, 4 Pair 6 Column Header Assembly, Double Wall, 4 Pair 6 Column Header Assembly, Left Wall, 4 Pair 6 Column Header Assembly, Right Wall, 4 Pair 6 Column Header Assembly, Left Wall, 4 Pair 14 Column Header Assembly, Right Wall, 4 Pair 14 Column Header Assembly, Left Wall, 5 Pair 14 Column Header Assembly, Right Wall, 5 Pair 14 Column *As announced on 6/20/07, Tyco Electronics now offers the Z-PACK TinMan product line as a form, fit and function replacement to the Z-PACK MAX product line. This chart will assist in finding the Z-PACK TinMan connector part number if you have a Z-PACK MAX connector part number. 38 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Z-PACK TinMan High Speed, High Density Backplane Connector Part Number Index Note: This index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part No. 1934218 1934221 1934222 1934225 1934226 1934228 1934229 1934230 1934231 1934269 1934271 1934272 1934273 1934299 1934300 1934301 1934302 1934303 1934304 Page 6 6 7 7 8 8 8 33 30 9 12 10 11 17 18 19 20 14 15 Part No. 1934305 1934306 1934315 1934316 1934317 1934318 1934331 1934332 1934333 1934334 1934339 1934340 1934341 1934342 1934343 1934344 1934345 1934346 1934347 Page 13 16 13 16 14 15 9 12 10 11 17 18 19 20 17 18 19 20 21 Part No. 1934348 1934349 1934350 1934351 1934352 1934353 1934354 1934355 1934356 1934357 1934358 1934359 1934360 1934361 1934362 1934363 1934364 Page 22 21 22 23 24 23 24 25 26 25 26 25 26 35 34 32 31 Tooling Part Number Index Note: This index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part No. 1804790 1804791 1901457 Page 13, 14, 15, 16 9, 10, 11, 12 17, 18, 19, 20 39 Catalog 5-1773447-9 Revised 7-07 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Global Contacts Americas Argentina – Buenos Aires +54-11-4733-2200 Phone: Fax: +54-11-4733-2211 Brasil – São Paulo Phone: +55-11-3611-1311 Fax: +55-11-3611-0397 Canada – Toronto +905-475-6222 Phone: Fax: +905-474-5520 Product Information Center: (Technical Support) Phone: +905-470-4425 Fax: +905-474-5525 Colombia – Bogota Phone: +57-1-231-9398 +57-1-660-0206 Fax: Mexico – Mexico City +52-55-1106-0800 Phone: +01-800-733-8926 Fax: +52-55-1106-0901 For Latin/South American Countries not shown Phone: +54-11-4733-2015 Fax: +54-11-4733-2083 United States – Harrisburg, PA Phone: +717-564-0100 +717-986-7575 Fax: Product Information Center: (Technical Support) +800-522-6752 Phone: Fax: +717-986-7575 Asia/ Pacific Australia – Sydney Phone: +61-2-9554-2600 +61-2-9502-2556 Fax: Product Information Center: (Technical Support) +61-2-9840-8200 Phone: Fax: +61-2-9634-6188 Japan – Toyko Phone: +81-44-844-8111 +81-44-812-3207 Fax: Product Information Center: (Technical Support) +81-44-844-8013 Phone: Fax: +81-44-812-3200 New Zealand – Auckland Phone: +64-9-634-4580 +64-9-634-4586 Fax: Singapore – Singapore +65-6482-0311 Phone: Fax: +65-6482-1012 Philippines – Makati City Phone: +632-848-0171 +632-867-8661 Fax: Thailand – Bangkok Phone: +66-2-955-0500 Fax: +66-2-955-0505 India – Bangalore Phone: +91-80-285-40800 +91-80-285-40820 Fax: Korea – Seoul Phone: +82-2-3415-4500 +82-2-3486-3810 Fax: People’s Republic of China Hong Kong +852-2735-1628 Phone: Fax: +852-2735-0243 Vietnam and Indochina – Ho Chi Minh City Phone: +84-8 930-5546 Fax: +84-8 930-3443 Indonesia – Jakarta +65-6482-0311 Phone: Fax: +65-6482-1012 Malaysia – Kuala Lumpur +60-3-78053055 Phone: Fax: +60-3-78053066 Shanghai Phone: Fax: +86-21-2407-1588 +86-21-2407-1599 Taiwan – Taipei +886-2-8768-2788 Phone: Fax: +886-2-8768-2268 Europe/ Middle East/Africa Austria – Vienna Phone: +43-1 90 5 60-0 Fax: +43-1 90 5 60-1333 Belgium – Kessel-Lo Phone: +32-16-35-23-00 Fax: +32-16-35-23-52 Germany – Bensheim Phone: +49-6251-133-0 Fax: +49-6251-133-1600 Product Information Center: (Technical Support) Phone: +49-6251-133-1999 Fax: +49-6251-133-1988 Bulgaria – Sofia Phone: +359-2-971-2152 Fax: +359-2-971-2153 Germany – Langen Phone: +49-6103-709-0 Fax: +49-6103-709-1223 Czech Republic – Kurim Phone: +420-5-41-162-111 Fax: +420-5-41-162-223 Germany – Speyer Phone: +49-6232-30-0 Fax: +49-6232-30-2243 Denmark – Glostrup Phone: +45-43-480-452 Fax: +45-43-441-414 Germany - HTS Division – Neunkirchen Phone: +49-2247-305-0 Fax: +49-2247-305-122 Egypt – Cairo Phone: +20-2-29 04 281 Fax: +20-2-41 92 334 Greece – Athens Phone: +30-210-9370-396/397 Fax: +30-210-9370-655 Estonia – Tartu Phone: +372-5138-274 Fax: +372-7400-779 Hungary – Budapest Phone: +36-1-289-1000 Fax: +36-1-289-1010 Finland – Helsinki Phone: +358-95-12-34-20 Fax: +358-95-12-34-250 France – Cergy-Pontoise Phone: +33-1-3420-8888 Fax: +33-1-3420-8600 Product Information Center: (Technical Support) Phone: +33-1-3420-8943 Fax: +33-1-3420-8623 5-1773447-9–LUG–PDF–7-07 Printed in the U.S.A. Ireland – Dublin Phone: +353-1-820-3000 Fax: +353-1-820-9790 Israel – Yokneam Phone: +972-4-959-0508 Fax: +972-4-959-0506 Italy – Collegno (Torino) Phone: +39-011-4012-111 Fax: +39-011-4031116 Lithuania – Vilnius Phone: +370-5-2131-402 Fax: +370-5-2131-403 Netherlands – ’s-Hertogenbosch Phone: +31-73-624-62-46 Fax: +31-73-621-23-65 Product Information Center: (Technical Support) Phone: +31-73-6246-999 Fax: +31-73-6246-998 Norway – Nesbru Phone: +47-66-77-8886 Fax: +47-66-77-8855 Poland – Warsaw Phone: +48-22-45-76-700 Fax: +48-22-45-76-720 Romania – Bucharest Phone: +40-21-311-3479/3596 Fax: +40-21-312-0574 Russia – Moscow Phone: +7-495-926-5506/07/08/09 Fax: +7-495-926-5505 Russia – St. Petersburg Phone: +7-812-718-8192 Fax: +7-812-718-8193 Slovenia – Ljubljana Phone: +386-1561-3270 Fax: +386-1561-3240 South Africa – Port Elizabeth Phone: +2741-503-4500 Fax: +2741-581-0440 Spain – Barcelona Phone: +34-93-291-0330 Fax: +34-93-201-7879 Product Information Center: (Technical Support): Phone: +34-93-291-0330 Fax: +34-93-200-3779 Sweden – Upplands Väsby Phone: +46-8-50-72-50-00 Fax: +46-8-50-72-50-01 Switzerland – Steinach Phone: +41-71-447-0447 Fax: +41-71-447-0444 Turkey – Istanbul Phone: +90-212-281-8181/2/3 Fax: +90-212-281-8184 Ukraine – Kiev Phone: +380-044-206-2265 Fax: +380-044-206-2264 United Kingdom – Swindon Phone: +44-8706-080-208 Fax: +44-1793-572-516 Product Information Center: (Technical Support) Freephone GB: 0800-267-666 Phone: +44-8706-080-208 Fax: +44-208-420-8081 For Middle East/African Countries Not Shown Phone: +33-1-3420-8866 Fax: +33-1-3420-8300 Tyco Electronics Corporation www.tycoelectronics.com