AMPMODU Interconnection System
Locking Clip Contacts and Housings
Product Facts
■
Self-retaining contacts
provide permanent
connection with quick
connect and disconnect
■
Fast, easy installation with
no additional locking
hardware required
■
Mates with .025 [0.64]
square posts in a variety
of configurations
■
Single- and double-row
configurations in up to
20 positions on .100 [2.54]
centers
■
Modular design permits
end-to-end stacking
(double- row only) for
circuit grouping
■
Choice of tin or select gold
plating
■
Housings made of 94V-0
rated glass-filled polyester
■
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E28476
■
Certified by Canadian
Standards
Association,
File No. LR 7189
Typical Application
Single
Contact
(Page 224)
Performance
Characteristics
Contact Current Rating—3 amperes
Termination Resistance:
12 milliohms (max.)—Gold plated
contacts
16 milliohms (max.)—Tin plated
contacts
Durability— Ref. AMP Product
Specification 108-36028 and
108-36028-1
Both Ends
Closed
(for specified
no. of circuits—
housing size)
(Page 226)
Single Row
Both Ends
Closed
(Page 225)
Left End
Open (for
stacking to
left side)
(Page 226)
Right End
Open (for
stacking to
right side)
(Page 226)
PCBoard
.100 x .100
[2.54 x 2.54]
.200/.277*
[5.08/7.04]
(without
housing
5
Extraction
Tool Slot
Contact
Clearance
Hole
.025
[0.64]
Sq. Posts
.273/.350*
[6.93/8.89]
(with housing)
*If post is longer than maximum specified, post tip may butt against wire ends.
Dimension defines .025 x .025 [0.64 x 0.64] portion of post.
223
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Locking Clip Contacts
Wire Crimp Contacts
with Insulation Support
Body
Material and Finish:
Contact Spring—Stainless steel
Plating A—Selectively plated .000050
[0.00127] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating B—Selectively plated .000030
[0.00076] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating C—.000100-.000200
[0.00254-0.00508] bright tin-lead
over .000050 [0.00127] nickel on
entire contact
Wire Size
Range
AWG
[mm2]
Spring
A
Ins.
Dis.
Range
Dimension
A
30-28
0.05-0.09
.029-.039 [0.74-0.99]
.550 [13.97]
26-22
0.12-0.4
.038-.062 [0.97-1.57]
.584 [14.83]
20
0.5-0.6
.038-.062 [0.97-1.57]
.584 [14.83]
Heavy Duty Miniature
Hand
Applicator for
Tool
AMP-O-LECTRIC
Strip Form Loose Piece
No.
Machine*
87190-1
87191-1
567310-2
90295-1
87190-2
87191-2
87124-3
87165-3
87124-1
87165-1
466721-2
91533-1
87124-2
87165-2
867052-2
—
679996-2
90431-1
867052-1
—
Part Nos.
Finish
Plating B
Plating C
Plating A
Plating B
Plating C
Plating B
Plating C
*For use with AMP-O-LECTRIC Model “K” machines. Call the Technical Support Center (1-800-522-6752) for part nos. of applicators for use with the
AMP-O-LECTRIC Model “G” machines (shown on page 289), as well as other bench machines and fully automatic AMPOMATORlead making machines.
Notes: 1. These contacts must be crimped in accordance with Tyco ElectronicsSpecification No. 114-25006 in order to function properly in a connector housing.
Notes: 2. Extraction Tool No. 91084-1 is used for removing individual contacts from connector housings and for detaching contacts from mating posts.
Related Product Data:
Housings Used With—
pages 225, 226
Application Tooling—
page 290
Technical Documents (page 295,
296):
Product Specification 108-36028,
108-36028-1
Application Specification
114-25006
5
Wire Harnessing
If necessary, wires can be
grouped with cable ties and
secured to a panel with
fixed clamps. However,
locking clip contacts must
be free to float within the
connector housings to allow
proper extraction.
Therefore, harnessing
hardware or the use of
multiple terminations per
contact must not restrict the
free-floating action of
contacts in the housing.
Fixed
Clamp
Unrestricted
Wires for
Free-Floating
Contacts
Cable
Tie
For more information
request Insulation and
Bundling Products Catalog
124132.
Extraction Tool
No. 91084-1
224
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Wire-Applied Housings for Locking Clip Contacts,
Single-Row, .100 [2.54] Centerline
.060
[1.52]
Single-Row
.700
[17.78]
.350
.273 (Post
8.89 Length)
6.93
[ ]
Material:
Glass-filled polyester, 94V-0 rated
.145
[3.68]
Related Product Data:
.025 [0.64]
Sq. Post
(Shown for
Ref. only)
A
Contacts—page 224
Mateable Headers and Posts—
Refer to the Mating Post Selection
Guide—page 89
.085
[2.16]
.175
[4.44]
C
Typ.
.100
Typ.
[2.54]
Technical Documents (pages 295,
296):
B
Product Specification 108-36028,
108-36028-1
Application Specification
114-25006
Note: Housing illustrated above is the “Both Ends Closed” version.
.125 [3.18] centerline single-row,
2 and 3 position housings are
available, Base Part No. 104905.
They are designed to be stackable
end-to-end and side-by-side.
Consult Tyco Electronics.
No. of
Pos.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Keying Plug:
A
.108 [2.74]
.216 [5.49]
.316 [8.03]
.416 [10.57]
.516 [13.11]
.616 [15.65]
.716 [18.19]
.816 [20.73]
.916 [23.27]
1.016 [25.81]
1.116 [28.35]
1.216 [30.89]
1.316 [33.43]
1.416 [35.97]
1.516 [38.51]
Dimensions
B
—
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
C
.054 [1.37]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
.058 [1.47]
Housing Part No.
Unstamped
Stamped
87175-2
—
87175-6
—
87175-8
—
1-87175-0
—
1-87175-2
—
1-87175-4
1-87175-3
1-87175-6
1-87175-5
1-87175-8
1-87175-7
2-87175-0
1-87175-9
2-87175-2
2-87175-1
2-87175-4
2-87175-3
2-87175-6
2-87175-5
2-87175-8
2-87175-7
3-87175-0
2-87175-9
87175-4
87175-3
5
Part No. 87179-1
(Plugs directly into housings for
.025 [0.64] square post contacts)
Material—Yellow, nylon
225
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Wire-Applied Housings for Locking Clip Contacts,
Double-Row, .100 x .100 [2.54 x 2.54] Centerline
Double-Row
.300
[7.62]
.700
[17.78]
.350 Max.
[8.89]
(Post
Length)
Material:
Glass-filled polyester, 94V-0 rated
.270
[6.86]
Related Product Data:
.025 [0.64]
Sq. Post
(Shown for
Ref. only)
A
.100
Typ.
[2.54]
.100
[2.54]
Contacts—page 224
Mateable Headers and Posts—
Refer to the Mating Post Selection
Guide—page 89
.058
[1.47]
Technical Documents (pages 296,
297):
B
Note: Housing illustrated above is the “Both Ends Closed” version.
Product Specification 108-36028,
108-36028-1
Application Specification
114-25006
Both Ends Closed
Key
Right End Open
Housing
Configuration
Keying Plug:
Both Ends Closed
5
Right End Open
Part No. 87179-1
(Plugs directly into housings for
.025 [0.64] square post contacts)
Left End Open
No. of
Pos.
2
4
6
8
10
12
16
18
20
4
10
20
4
10
20
Keyway
Dimensions
A
B
.116 [2.95]
—
.216 [5.49]
.100 [2.54]
.316 [8.03]
.200 [5.08]
.416 [10.57]
.300 [7.62]
.516 [13.11]
.400 [10.16]
.616 [15.65]
.500 [12.70]
.816 [20.73]
.700 [17.78]
.916 [23.27]
.800 [20.32]
1.016 [25.81]
.900 [22.86]
.216 [5.49]
.100 [2.54]
.516 [13.11]
.400 [10.16]
1.016 [25.81]
.900 [22.86]
.216 [5.49]
.100 [2.54]
.516 [13.11]
.400 [10.16]
1.016 [25.81]
.900 [22.86]
Left End Open
Housing Part No.
Unstamped
Stamped
87176-2
—
87133-1
—
87133-7
87133-8
87133-9
1-87133-0
87133-2
87133-5
1-87133-1
1-87133-2
1-87133-3
1-87133-4
1-87133-5
1-87133-6
87133-3
87133-6
87132-1
—
87132-2
87132-5
87132-3
87132-6
87131-1
—
87131-2
87131-5
87131-3
87131-6
Material—Yellow, nylon
226
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Contacts and Housings
Product Facts
■
Terminates 32-20 AWG
[0.03-0.6mm2] discrete wire
■
Contacts have insulation
support
■
Choice of three contact
mating pressures
■
Available in a variety of
gold and tin platings
■
Receptacles mate with .025
[0.64] square or round
posts
■
Dual cantilever contact
beam with built-in antioverstress feature for
reliable matings
■
Housings accept a variety of
receptacle and pin contacts
■
Housing sizes range up to
100 positions
■
Housing configurations
include single- and doublerows on .100 [2.54]
centerlines
■
Housing options include
detent latching, polarization
and bonded strain relief/
pull tabs
■
■
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
Certified by Canadian
Standards
Association,
1-87631-5 D-R Housing, Polarized with Detent
1-87756-6 Std. Pressure Contacts
Wire-to-Board
1-87456-5 D-R Housing, Plain
1-87756-6 Std. Pressure Contacts
102387-1 D-R Ejection Housing,
Center Polarized
1-87756-6 Std. Pressure Contacts
87483-3 D-R Housing with Mounting Ears
1-87756-6 Std. Pressure Contacts
102241-8 S-R Housing Polarized with
Detent
102128-1 High Pressure Contacts
102186-1 Latch
102154-1 Hdr
103166-8 Hdr
3-87977-5 D-R Housing, Polarized
1-87756-6 Std. Pressure Contacts
103168-8
Hdr
1-87756-6 Std. Pressure Plain
1-87456-6 D-R Housing, Contacts
1-87232-0
Hdr
103166-8 Hdr
Performance
Characteristics
1-87499-8 S-R Housing, Plain
102128-1 High Pressure Contacts
102202-7 Hdr
Contact Current Rating—3 amperes
Termination Resistance:
12 milliohms (max.)—Beryllium copper
contacts
20 milliohms (max.)—Copper-tinphosphor bronze contacts
Durability—Ref. AMP Product
Specification 108-25020
5
227
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Pin and Receptacle Contacts
Crimp Snap-In (No-strip)
Receptacles and Crimp
Snap-In Pins with
Insulation Support
(Standard Pressure)
.058
[1.47]
No-Strip
Receptacle
.165
[4.19]
.016
[0.41]
Gap Max.
Pin with
Insulation Support
.815
[20.70]
.470
[11.94]
.068
[1.73]
Crimp Snap-In (No-strip) Receptacles
.
Ins.
Dia.
Range
Finish
040-.055 [1.02-1.40]
Plating A
Plating C
Part Nos.
Strip Form
Loose Piece
87107-5
87107-6
102348-2
102348-3
Heavy Duty Miniature
Applicator No.
for AMP-O-LECTRIC
Machine*
Hand
Tool
Part No.
567307-2
90381-1
Standard Pressure
Configuration
Material and Finish:
Beryllium copper or phosphor bronze
(see charts), plated as follows:
Plating A—Selectively plated .000030
[0.00076] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating B—Selectively plated .000015
[0.00038] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating C—.000100-.000200
[0.00254-0.00508] bright tin-lead over
.000030 [0.00076] nickel on entire
contact
Crimp Snap-In Pins with Insulation Support
Wire
Size
Range
AWG
[mm2]
26-22
Ins.
Dia.
(Max.)
0.12-0.4 .061 [1.55]
Finish
Plating A
Plating B
Plating C
Hand
Heavy Duty Miniature
Tool
Applicator No.
Part
No.
for
AMP-O-LECTRIC
Strip Form Loose Piece
Machine*
Premium Commercial
102095-3 102107-2
102095-2 102107-1
466812-2
91517-1
58641-1†
102095-4 102107-3
Part Nos.
*For use with AMP-O-LECTRIC Model “K” machines. Call the Technical Support Center (1-800-522-6752) for part
nos. of applicators for use with the AMP-O-LECTRIC Model “G” machines (shown on page 289), as well as other
bench machines and fully automatic AMPOMATORlead making machines.
†PRO-CRIMPER II hand tool frame with die set assembly.
Die Set Part No. 58641-2
Related Product Data:
Housings Used With—
pages 231-237
Performance Characteristics—
page 227
Application Tooling—
page 290
Technical Documents (pages 294,
296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
5
Additional header sizes are
available; minimum order
quantities may apply.
Consult Tyco Electronics.
228
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Receptacle Contacts
Crimp Snap-In Receptacles
with Insulation Support
(Standard, Intermediate
and High Pressure)
Standard Pressure
A
.058
[1.47]
Material and Finish:
Beryllium copper, phosphor bronze or
copper-tin-phosphor bronze (see charts,
page 139), plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000100.000200 [0.00254-0.00508] tin-lead on
crimp area, with entire contact
underplated .000050 [0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000100.000200 [0.00254-0.00508] tin-lead in
crimp area, with entire contact
underplated .000050 [0.00127] nickel
Plating D—Selectively plated .000050
[0.00127] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating E—Selectively plated .000030
[0.00076] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating F—Selectively plated .000015
[0.00038] gold on contact area, with gold
flash over .000050 [0.00127] nickel on
entire contact
Plating G—.000100-.000200
[0.00254-0.00508] bright tin-lead over
.000030 [0.00076] nickel on entire
contact
.165
[4.19]
A
.068
[1.73]
Intermediate Pressure
A
High Pressure
A
Related Product Data:
Housings Used With—
pages 231-237
Performance Characteristics—
page 227
Application Tooling—
page 290
Technical Documents (pages 294,
296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
Standard Pressure
Intermediate Pressure
High Pressure
Mating Force
9 oz. Max.
16 oz. Max.
20 oz. Max.
Unmating Force
1.5 oz. Min.
2 oz. Min.
3 oz. Min.
A-Gap Dimension
.008/.014
.008/.014
.013±.002
5
229
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Receptacle Contacts (Continued)
Standard Pressure (Mod IV)
Wire
Size
Range
AWG [mm2]
Ins.
Dia.
(Max.)
Dimension
A
32-27 0.03-0.1
.040 [1.02]
.445 [11.30]
26-22 0.12-0.4
.061 [1.55]
.445 [11.30]
24-20 0.2-0.6
.069 [1.75]
.470 [11.94]
Material
Cu-Sn-PhBz
Cu-Sn-Ph Bz
Be Cu
Be Cu
Be Cu
Cu-Sn-PhBz
Cu-Sn-PhBz
Cu-Sn-Ph Bz
Cu-Sn-Ph Br
Be Cu
Be Cu
Be Cu
Be Cu
Cu-Sn-PhBz
Cu-Sn-Ph Bz
Be Cu
Be Cu
Cu-Sn-Ph Br
Be Cu
Finish
Heavy Duty Miniature Applicator for
Applicator for
Stripper/
AMP-O-LECTRIC
Crimper
Machine*
Machine
1-102316-4
1-102316-3
1-102917-2
466655-2
466921-1
102917-2
102917-6
1-102316-2
1-87756-8
1-87756-6
87756-7
87667-5
466571-2
466918-1
87667-2
87667-5
87667-3
1-87523-9
1-87523-6
86016-2
466562-2
466905-1
86016-5
87523-6
86016-3
Hand
Tool
Part Nos.
Premium Commercial
Heavy Duty Miniature Applicator for
Applicator for
Stripper/
AMP-O-LECTRIC
Crimper
Machine*
Machine
Hand
Tool
Part Nos.
Premium Commercial
Part Nos.
Strip Form Loose Piece
Plating A
102316-8
Plating B
102316-6
Plating D 1-102917-1
Plating E
102917-1
Plating F
102917-5
Plating G
102316-5
Plating A 1-87756-7
Plating B 1-87756-2
Plating G
87756-6
Plating D 1-87666-6
Plating E
87666-2
Plating F
87666-5
Plating G
87666-3
Plating A 1-87523-8
Plating B 1-87523-5
Plating E
85969-8
Plating F
85969-6
Plating G
87523-5
Plating G
85969-9
91541-1
—
91517-1
58641-1†
91516-2
—
Intermediate Pressure (Mod IV.v)
Wire
Size
Range
AWG [mm2]
Ins.
Dia.
(Max.)
Dimension
A
32-27 0.03-0.1
.040 [1.02]
.445 [11.30]
26-22 0.12-0.4
.061 [1.55]
.445 [11.30]
24-20 0.2-0.6
.069 [1.75]
.470 [11.94]
Material
Finish
Cu-Sn-Ph Bz
Be Cu
Cu-Sn-PhBz
Cu-Sn-Ph Bz
Be Cu
Be Cu
Cu-Sn-PhBz
Cu-Sn-Ph Bz
Be Cu
Be Cu
Be Cu
Plating A
Plating E
Plating A
Plating B
Plating E
Plating F
Plating A
Plating B
Plating E
Plating F
Plating G
Part Nos.
Strip Form Loose Piece
102920-1
102918-1
103171-4
103171-1
102548-5
102548-1
2-87195-0
1-87195-7
86492-6
86492-2
86492-9
102920-2
102918-2
103171-5
103171-2
102548-6
102548-3
2-87195-1
1-87195-8
87046-3
87046-1
87046-4
466655-2
466921-1
91541-1
—
466571-2
466918-1
91517-1
58641-1 †
466562-2
466905-1
91516-1
—
High Pressure (Mod V)**
Wire
Size
Range
AWG
[mm2]
32-27 0.03-0.1
Ins.
Dia.
(Max.)
Dimension
A
Material
Finish
.040 [1.02]
.445 [11.30]
26-22 0.12-0.4
.061 [1.55]
.445 [11.30]
24-20
.069 [1.75]
.470 [11.94]
Ph Bz
Ph Bz
Ph Bz
Ph Bz
Ph Bz
Plating E
Plating E
Plating G
Plating E
Plating G
0.2-0.6
Part Nos.
Strip Form Loose Piece
103455-1
103455-2
87809-1
102128-1
87809-2
102128-2
87309-9
1-87309-4
87309-8
1-87309-3
Heavy Duty Miniature
Applicator for
AMP-O-LECTRIC
Machine*
466655-2
Applicator for
AMP-O-MATIC
Stripper/Crimper
Machine
466921-1
Hand
Tool
Part Nos.
466571-2
466918-1
91517-1
466562-2
466905-1
91516-1
91541-1
**For use with AMP-O-LECTRIC Model “K” machines. Call the Technical Support Center (1-800-522-6752) for part nos. of applicators for use with the
AMP-O-LECTRIC Model “G” machines (shown on page 289), as well as other bench machines and fully automatic AMPOMATORlead making machines.
**Contact material is phosphor bronze.
†PRO-CRIMPER II hand tool frame with die set assembly.
Die Set Part No. 58641-2
5
230
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Single-Row, .100 [2.54] Centerline
Non-Polarized
.600
[15.24]
.175
[4.45]
Material:
Black thermoplastic, flame retardant
A
Max.
.050
[1.27]
Typ.
Related Product Data:
Contacts—pages 228-230
Mateable Headers and Posts—
pages 92-94, 100-104, 110-112
.070
[1.78]
Typ.
B ±.003
[±0.08]
.100
Typ.
[2.54]
C ±.003
[±0.08]
.072
[1.83]
.140
[3.56]
X
X
Section X-X
Technical Documents (page 294296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
Keying Plugs
Part No. 86286-1
(Plugs into standard or intermediate
pressure receptacle contact)
Material—Natural color nylon
Part No. 87077-2
(Plugs directly into housing)
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
No. of
Pos.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
A
.105 [2.67]
.205 [5.21]
.305 [7.75]
.405 [10.29]
.505 [12.83]
.605 [15.37]
.705 [17.91]
.805 [20.45]
.905 [22.99]
1.005 [25.53]
1.105 [28.01]
1.205 [30.61]
1.305 [33.15]
1.405 [35.69]
1.505 [38.23]
1.605 [40.77]
1.700 [43.18]
1.805 [45.85]
1.900 [48.26]
2.005 [50.93]
2.100 [53.34]
2.205 [56.01]
2.300 [58.42]
2.400 [60.96]
2.500 [63.50]
2.605 [66.17]
2.700 [68.58]
2.800 [71.12]
2.900 [73.66]
3.005 [76.33]
3.100 [78.74]
3.200 [81.28]
3.300 [83.82]
3.400 [86.36]
3.500 [88.98]
3.600 [91.44]
Dimensions
B
—
.100 [2.54]
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.500 [38.10]
1.600 [40.64]
1.600 [40.64]
1.700 [43.18]
1.700 [43.18]
1.800 [45.72]
Part No.
C
—
—
.100 [2.54]
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.500 [38.10]
1.600 [40.64]
1.600 [40.64]
1.700 [43.18]
1.700 [43.18]
Stamped*
—
87499-3
87499-5
87499-7
87499-9
1-87499-1
87499-1
1-87499-3
1-87499-5
1-87499-7
1-87499-9
2-87499-1
2-87499-3
2-87499-5
2-87499-7
2-87499-9
—
—
—
3-87499-7
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Unstamped**
7-87499-2
87499-4
87499-6
87499-8
1-87499-0
1-87499-2
87499-2
1-87499-4
1-87499-6
1-87499-8
2-87499-0
2-87499-2
2-87499-4
2-87499-6
2-87499-8
3-87499-0
3-87499-2
3-87499-4
3-87499-6
3-87499-8
4-87499-0
4-87499-2
4-87499-4
4-87499-6
4-87499-8
5-87499-0
5-87499-2
5-87499-4
5-87499-6
5-87499-8
6-87499-0
6-87499-2
6-87499-4
6-87499-6
6-87499-8
7-87499-0
**Cavity identification, part number and date code stamped on housing where size permits.
**No marking on housing.
Notes: 1. Strain reliefs are available and may be purchased separately. Consult Tyco Electronics.
Notes: 2. Contact Extraction/Lance Reset Tool No. 843996-3.
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
5
231
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Single-Row, .100 [2.54] Centerline (Continued)
Polarized (with
Detent Latching)
Recessed Area
.175
[4.45]
A
Material:
Black thermoplastic, flame retardant
.050 Typ.
[1.27]
Related Product Data:
Contacts—pages 228-230
Mateable Headers and Posts—
pages 129-131
Flexible Film Connectors,
Single-Row Pin Assemblies—
Catalog 82007
±.003
B [±0.08]
.071
[1.80]
C ±.003
[±0.08]
.600
[15.24]
X
.072
[1.83]
.182
[4.62]
X
.056
[1.42]
.100
[2.54]
Typ.
.100
[2.54]
Typ.
.127
[3.23]
Section X-X
Technical Documents: (pages 294,
296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
Keying Plugs
Part No. 86286-1
(Plugs into standard or intermediate
pressure receptacle contact)
Material—Natural color nylon
5
Part No. 87077-2
(Plugs directly into housing)
No. of
Pos.
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
A
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.300 [58.42]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
2.700 [68.58]
2.800 [71.12]
2.900 [73.66]
3.000 [76.20]
3.100 [78.74]
3.200 [81.28]
3.300 [83.82]
3.400 [86.36]
3.500 [88.90]
3.600 [91.44]
Dimensions
B
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.500 [38.10]
1.600 [40.64]
1.600 [40.64]
1.700 [43.18]
1.700 [43.18]
1.800 [45.72]
C
.100 [2.54]
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.500 [38.10]
1.600 [40.64]
1.600 [40.64]
1.700 [43.18]
1.700 [43.18]
Part Nos.
Unstamped*
102241-1
102241-2
102241-3
102241-4
102241-5
102241-6
102241-7
102241-8
102241-9
1-102241-0
1-102241-1
1-102241-2
1-102241-3
1-102241-4
1-102241-5
1-102241-6
1-102241-7
1-102241-8
1-102241-9
2-102241-0
2-102241-1
2-102241-2
2-102241-3
2-102241-4
2-102241-5
2-102241-6
2-102241-7
2-102241-8
2-102241-9
3-102241-0
3-102241-1
3-102242-2
3-102241-3
3-102241-4
*No marking on housing.
Note: Contact Extraction/Lance Reset Tool No. 843996-3.
232
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Double-Row,
.100 x .100 [2.54 x 2.54] Centerline
Non-Polarized
.175
[4.45]
A
Material:
Black thermoplastic, flame retardant
.100 Typ.
[2.54]
.050
[1.27]
Typ.
.240
[6.10]
B
X
C
.100
[2.54]
R
Optional
Related Product Data:
X
Contacts—pages 228-230
Mateable Headers and Posts—
pages 95-97, 105-109, 133-135
.070
[1.78]
Section X-X
.072
[1.83]
Technical Documents (pages 294,
296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
Keying Plugs
Part No. 86286-1
(Plugs into standard or intermediate
pressure receptacle contact)
Material—Natural color nylon
Part No. 87077-1
(for .645 high housings)
Part No. 87077-2
(for .600 high housings)
(Plugs directly into housing)
No.
of
Pos.
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
48
50
52
54
56
58
60
64
66
70
72
Dimensions
A
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
2.700 [68.58]
2.800 [71.12]
2.900 [73.66]
3.000 [76.20]
3.200 [81.28]
3.300 [83.82]
3.500 [88.90]
3.600 [91.44]
B
—
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.300 [58.42]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
2.700 [68.58]
2.800 [71.12]
2.900 [73.66]
3.100 [78.74]
3.200 [81.28]
3.400 [86.36]
3.500 [88.90]
Part Nos.
C = .600 [15.24]
Stamped*
Unstamped**
—
5-87456-3
5-87456-0
4-87456-9
87456-2
87456-1
87456-4
87456-3
87456-6
87456-5
87456-8
87456-7
1-87456-0
87456-9
1-87456-2
1-87456-1
1-87456-4
1-87456-3
1-87456-6
1-87456-5
—
1-87456-7
2-87456-0
1-87456-9
2-87456-2
2-87456-1
2-87456-4
2-87456-3
2-87456-6
2-87456-5
2-87456-8
2-87456-7
3-87456-0
2-87456-9
3-87456-2
3-87456-1
—
3-87456-3
3-87456-6
3-87456-5
4-87456-4
4-87456-3
3-87456-8
3-87456-7
6-87456-0
5-87456-9
4-87456-0
3-87456-9
4-87456-2
4-87456-1
—
4-87456-5
—
6-87456-1
—
6-87456-3
5-87456-2
5-87456-1
6-87456-6
6-87456-5
5-87456-4
5-87456-7
—
5-87456-5
4-87456-8
4-87456-7
C = .645 [16.38]
Unstamped**
—
2-86177-5
1-86177-8
2-86177-0
1-86177-2
1-86177-3
1-86177-4
1-86177-5
1-86177-6
86177-1
86177-2
86177-3
86177-4
86177-5
86177-6
86177-7
86177-8
86177-9
1-86177-0
1-86177-1
—
1-86177-7
2-86177-3
2-86177-1
1-86177-9
—
—
—
—
—
—
2-86177-4
—
5
**Cavity identification, AMP, part number and date code stamped on housing where size permits.
**No marking on housing.
Notes: 1.Strain reliefs are available and may be purchased separately. Consult Tyco Electronics.
Notes: 2. Contact Extraction/Lance Reset Tool No. 843996-3.
233
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Double-Row,
.100 x .100 [2.54 x 2.54] Centerline (Continued)
Strain Relief Locators
(on Housings 20 Positions
and Larger)
Polarized
.175
[4.45]
Material:
Black thermoplastic, flame retardant
A
Related Product Data:
±.003
B [±0.08]
Contacts—pages 228-230
Mateable Headers and Posts—
pages 133-148
.100
[2.54]
Typ.
C ±.003
[±0.08]
.100
[2.54]
X
Typ.
.050
[1.27]
Typ.
.600
[15.24]
.070 Typ.
[1.78]
R
Optional
.240
[6.10]
Technical Documents (pages 294,
.100
[2.54]
296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
Keying Plugs
Part No. 86286-1
(Plugs into standard or intermediate
pressure receptacle contact)
Material—Natural color nylon
5
Part No. 87077-2
(Plugs directly into housing)
Section X-X
X
No. of
Pos.
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
48
50
52
54
56
58
60
64
66
70
72
A
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
2.700 [68.58]
2.800 [71.12]
2.900 [73.66]
3.000 [76.20]
3.200 [81.28]
3.300 [83.82]
3.500 [88.90]
3.600 [91.44]
Dimensions
B
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
C
.100 [2.54]
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.700 [43.18]
Stamped*
87977-1
87977-2
87977-3
87977-4
87977-5
87977-6
—
87977-8
—
1-87977-0
1-87977-1
—
—
—
—
—
—
1-87977-8
—
—
—
2-87977-1
—
—
—
—
2-87977-4
—
—
—
—
Part Nos.
Unstamped**
2-87977-8
2-87977-9
3-87977-0
3-87977-1
3-87977-2
3-87977-3
3-87977-4
3-87977-5
3-87977-6
3-87977-7
3-87977-8
3-87977-9
4-87977-0
4-87977-1
4-87977-2
4-87977-3
4-87977-4
4-87977-5
4-87977-6
4-87977-7
5-87977-6
4-87977-8
4-87977-9
5-87977-0
5-87977-8
6-87977-0
5-87977-1
6-87977-2
5-87977-2
5-87977-3
5-87977-4
**Cavity identification, AMP, part number and date code stamped on housing where size permits.
**No marking on housing or strain relief.
Notes: 1. Strain reliefs are available and may be purchased separately. Consult Tyco Electronics.
Notes: 2. Contact Extraction/Lance Reset Tool No. 843996-3.
234
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Double-Row,
.100 x .100 [2.54 x 2.54] Centerline (Continued)
Polarized (with Detent
Latching, with and without
Strain Relief/Pull Tab)
Strain Relief Locators
(on Housings 20 Positions
and Larger)
.175
[4.45]
A
Material:
B ±.003
C ±.003
[±0.08]
Black thermoplastic, flame retardant
[±0.08]
.100 Typ.
[2.54]
.100 Typ.
[2.54]
Related Product Data:
.050
[1.27]
Typ.
X
Contacts—pages 228-230
Mateable Headers and Posts—
pages 133-141, 144-149
Technical Documents (pages 294,
Section X-X
X
296):
.500
[12.70]
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
1.150
[29.21]
Housing with
Strain Relief/Pull Tab
Strain Relief Part No. 87710-1
(20 positions and larger)
Dimensions
A
6
8
10
12
14
16
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
C
No. of
Detents
.100 [2.54]
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
1
1
1
1
1
1
B
.100 [2.54]
.200 [5.08]
.200 [5.08]
.300 [7.62]
.300 [7.62]
.400 [10.16]
1.900
[48.26]
.095
[2.41]
Dia.
Housing with
Strain Relief/Pull Tab
Strain Relief Part No. 87921-1
(10 thru 18 positions)
No. of
Pos.
R
Optional
1.000
[25.40]
.095
[2.41]
Dia.
Keying Plugs
Material—Natural color nylon
.240
[6.10]
.070
[1.78]
Typ.
.100
[2.54]
Part No. 86286-1
(Plugs into standard or intermediate
pressure receptacle contact)
.600
[15.24]
Part Nos.
Without Strain Relief
With Strain Relief
Stamped*
Unstamped**
Stamped*
87631-2
87631-1
—
87631-4
87631-3
—
87631-6
87631-5
87922-1
87631-8
87631-7
87922-2
1-87631-0
87631-9
87922-3
1-87631-2
1-87631-1
87922-4
5
**Cavity identification, AMP, part number and date code stamped on housing and/or strain relief where size permits.
**No marking on housing or strain relief.
Notes: 1. The Strain Relief/Pull Tab can be bonded to any thermoplastic connector housing.
Notes: 2. Strain reliefs may be purchased separately.
Notes: 3. Contact Extraction/Lance Reset Tool No. 843996-3.
Part No. 87077-2
(Plugs directly into housing)
235
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Double-Row,
.100 x .100 [2.54 x 2.54] Centerline (Continued)
Dimensions
No. of
Pos.
18
20
22
24
26
28
30
32
34
36
38
40
42
44
48
50
52
54
58
60
64
66
70
72
A
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
2.700 [68.58]
2.900 [73.66]
3.000 [76.20]
3.200 [81.28]
3.300 [81.28]
3.500 [88.90]
3.800 [96.52]
B
C
No. of
Detents
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
.400 [10.16]
.400 [10.16]
.500 [12.70]
.500 [12.70]
.600 [15.24]
.600 [15.24]
.700 [17.78]
.700 [17.78]
.800 [20.32]
.800 [20.32]
.900 [22.86]
.900 [22.86]
1.000 [25.40]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.700 [43.18]
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Part Nos.
Without Strain Relief
With Strain Relief
Stamped*
Unstamped**
Stamped*
1-87631-4
1-87631-3
87922-5
1-87631-6
1-87631-5
87733-1
1-87631-8
1-87631-7
—
2-87631-0
1-87631-9
87733-3
2-87631-2
2-87631-1
87733-4
2-87631-4
2-87631-3
—
2-87631-6
2-87631-5
87733-6
2-87631-8
2-87631-7
87733-7
3-87631-0
2-87631-9
87733-8
3-87631-2
3-87631-1
—
—
3-87631-3
—
3-87631-6
3-87631-5
1-87733-1
3-87631-8
3-87631-7
—
4-87631-0
3-87631-9
—
—
5-87631-9
—
4-87631-2
4-87631-1
1-87733-4
—
4-87631-3
—
4-87631-6
4-87631-5
—
—
6-87631-3
—
5-87631-2
5-87631-1
1-87733-7
6-87631-6
6-87631-5
—
—
5-87631-3
—
—
5-87631-5
—
5-87631-8
5-87631-7
—
**Cavity identification, AMP, part number and date code stamped on housing and/or strain relief where size permits.
**No marking on housing or strain relief.
Notes: 1. The Strain Relief/Pull Tab can be bonded to any thermoplastic connector housing.
Notes: 2. Strain reliefs may be purchased separately.
Notes: 3. Contact Extraction/Lance Reset Tool No. 843996-3.
5
236
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Mod IV Wire-Applied Housings, Double-Row,
.100 x .100 [2.54 x 2.54] Centerline (Continued)
Position No. 1 Indicator
Center Polarized
.030
[0.76]
.150†
[3.81]
.570
[14.88]
.130
[3.30]
.130
[3.30]
B
A
Material:
Black thermoplastic, flame retardant
Related Product Data:
Contacts—pages 228-230
Mateable Headers and Posts:
Low Profile Shrouded Headers,
Double-Row, Straight or RightAngle Posts—pages 153-155
Low Profile Shrouded Headers,
Double-Row, Straight or RightAngle Posts, with .585 [14.86]
Ejection Latches—pages 156-157
AMP-LATCH Ejection Headers
with .576 [14.63] Ejection
Latches—Catalog 82012, Part Nos.
102186-1 & 102320-1
Technical Documents (pages 294,
296):
Product Specification 108-25007,
208-25019, 108-25020, 108-25021
Application Specification
114-25003, 114-25016
Keying Plugs
Part No. 86286-1
(Plugs into standard or intermediate
pressure receptacle contact)
.120
[3.05]
C
.600
[15.24]
.072
[1.83]
X
.285
[7.24]
.227
[5.77]
X
.100
[2.54]
R Optional
Section X-X
Dimensions
Part Nos.
No. of
Pos.
A
B
C
(Stamped*)
8
.580 [14.73]
.225 [5.72]
.300 [7.62]
1-102387-4
10
.680 [17.27]
.275 [6.98]
.400 [10.16]
102387-1
14
.880 [22.35]
.375 [9.53]
.600 [15.24]
102387-2
16
.980 [24.89]
.425 [10.80]
.700 [17.78]
102387-3
20
1.180 [29.97]
.525 [13.34]
.900 [22.86]
102387-4
22
1.280 [32.51]
.575 [14.61]
1.000 [25.40]
1-102387-5
24
1.380 [35.05]
.625 [15.88]
1.100 [27.94]
102387-5
26
1.480 [37.59]
.675 [17.15]
1.200 [30.48]
102387-6
30
1.680 [42.67]
.775 [19.69]
1.400 [35.56]
102387-7
34
1.880 [47.75]
.875 [22.23]
1.600 [40.64]
102387-8
40
2.180 [55.37]
1.025 [26.04]
1.900 [48.26]
102387-9
44
2.380 [60.45]
1.125 [28.58]
2.100 [53.34]
1-102387-3
50
2.680 [68.07]
1.275 [32.39]
2.400 [60.96]
1-102387-0
60
3.180 [80.77]
1.525 [38.74]
2.900 [73.66]
1-102387-1
64
3.380 [85.85]
1.625 [41.28]
3.100 [78.74]
1-102387-2
*Cavity identification and AMP stamped on housing.
†Non-functional slot is used for gating purposes during injection molding process. This gating feature is not inherent in
all production molds. Therefore, the depicted slot will only be present on housings produced on mold tooling requiring
this gating feature.
Note: Contact Extraction/Lance Reset Tool No. 843996-3.
Material—Natural color nylon
5
Part No. 87077-2
(Plugs directly into housing)
237
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Short Point, Crimp Snap-In Wire-Applied Contacts and Housings
Product Facts
■
Short point of contact
mates with .169 [4.29]
to .259 [6.58] long post
■
Double-row housings are
end-to-end and side-to-side
stackable
■
Terminates 32-20 AWG
[0.03-0.6 mm2] discrete
wire
■
Contacts have insulation
support to accept a
maximum insulation
diameter
of .060 [1.52]
■
Available with .000015
[0.00038] or .000030
[0.00076] gold duplex,
or bright tin-lead plating
■
Mates with .025 [0.64]
square posts
■
Dual cantilever contact
beams for reliable matings
■
Locking retention latch
provides 3 lb [13.34 N]
of retention force
■
Unique locking latch design
helps prevent latch from
protruding through latch
window
■
Contacts snap into
AMPMODU MTE single-row
housings
■
Double-row housing
configurations include .100
[2.54] centerline, plain and
polarized
■
Housing sizes range from
4 to 52 positions
■
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
■
5
■
Certified by Canadian
Standards
Association,
File No. LR7189
Produced under a Quality
Management System
certified to ISO 9001
A copy of the
certificate is available
upon request
104450-3 MTE Hdr
104257-3 MTE Recept. Housing
104480-7 Short Point Contact
1-87232-0 Hdr
Wire-to-Board
104482-9 Short Point Recept. Housing
104481-6 Short Point Contact
104257-5 MTE Recept. Housing
104480-8 Short Point Contact
103688-9 MTE Recept. Housing
104479-5 Short Point Contact
AMPMODU Short Point
receptacle contacts are
designed to mate with .025
[0.64] square posts. They
will mate with posts as short
as .169 [4.29].
Short Point double-row
housings are end-to-end
and side-to-side stackable
on .100 [2.54] centers.
Contacts also can be used
in single-row AMPMODU
MTE housings to provide
a complete wire-crimp
system, or to serve as
replacement contacts.
Performance
Characteristics
Contact Current Rating—3 amperes
Termination Resistance—
12 milliohms (max.)
Durability—Ref. Tyco Electronics
Product Specification 108-1472
238
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Short Point Crimp Snap-In Receptacle Contacts
Material and Finish:
.068
[1.73]
Copper alloy C7025, plated as follows:
Plating A—Duplex plated .000030
[0.00076] min. gold on contact area,
.000050 [0.00127] min. tin-lead in
crimp area, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating B—Duplex plated .000015
[0.00038] min. gold on contact area,
.000050 [0.00127] min. tin-lead in
crimp area, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating C—.000100 [0.00254] min.
bright tin-lead over .000050 [0.00127]
min. nickel on entire contact
.060
[1.52]
.460
[11.68]
Related Product Data:
Performance Characteristics—
page 238
Housings used in—
Short Point—pages 240, 241
AMPMODU MTE Unloaded
Housings—pages 245-250
Application Tooling—
page 290
C
C
.012
[0.30]
Gap
Technical Documents (page 294296):
Product Specification 108-1472,
108-25027
Application Specification
114-25038
Keying Plug
Part No. 104072-1
Ten plugs are supplied per strip.
Order quantity reflects the number
of strips required.
Wire Size
Range
AWG
[mm2]
Ins.
Dia.
Range
32-28
0.03-0.08
.025-.060 [0.64-1.52]
26-22
0.13-0.3
.
.025-.060 [0.64-1.52]
24-20
0.2-0.5
.
.025-.060 [0.64-1.52]
Section C - C
Photo 4857
Extraction/Lance Reset
Tool No. 843477-1
Finish
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
Contact Part No.
(Standard Pressure)
Strip Form Loose Piece
104481-4
104481-3
104481-2
104480-4
104480-3
104480-2
104479-4
104479-3
104479-2
104481-8
104481-7
104481-6
104480-9
104480-8
104480-7
104479-7
104479-6
104479-5
Quick-Change
Applicator for
AMP-O-LECTRIC
Machine*
Applicator for
AMP-O-MATIC
Stripper/Crimper
Machine
Hand
Tool
Nos.
567296-2
466980-1
91518-1
567297-2
466981-1
91518-1
567298-2
466982-1
91551-1
5
*For use with Model “K” machines. Call the Tooling/Technical Assistance Center (1-800-722-1111) for part nos. of applicators for use with the Model “G”
machines (shown on page 289), as well as other bench machines and fully automatic AMPOMATOR lead making machines.
239
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Short Point Wire-Applied Housings, Double-Row, Non-Polarized,
.100 x .100 [2.54 x 2.54] Centerline
A
Material:
Black thermoplastic, flame retardant,
94V-0 rated
Related Product Data:
Performance Characteristics—
page 238
Contacts—page 239
Mateable Headers—pages 105-108,
113, 114
B
.049
[1.24]
X
.049
[1.24] 2 Plc.
.036
[0.91]
.600
[15.24]
.198
[5.03]
.100
[2.54]
.100
[2.54] Typ.
0.72
[1.83]
X
Section X-X
Technical Documents (page 294296):
Product Specification 108-1472,
108-25027
Application Specification
114-25038
No. of
Pos.
4
6
8
10
12
14
16
18
20
22
26
28
30
32
34
36
38
40
44
52
Dimensions
A
B
.198 [5.03]
.100 [2.54]
.298 [7.57]
.200 [5.08]
.398 [10.11]
.300 [7.62]
.498 [12.65]
.400 [10.16]
.598 [15.19]
.500 [12.70]
.698 [17.73]
.600 [15.24]
.798 [20.27]
.700 [17.78]
.898 [22.81]
.800 [20.32]
.998 [25.35]
.900 [22.86]
1.098 [27.89]
1.000 [25.40]
1.298 [32.97]
1.200 [30.48]
1.398 [35.51]
1.300 [33.02]
1.498 [38.05]
1.400 [35.56]
1.598 [40.59]
1.500 [38.10]
1.698 [43.13]
1.600 [40.64]
1.798 [45.67]
1.700 [43.18]
1.898 [48.21]
1.800 [45.72]
1.998 [50.75]
1.900 [48.26]
2.198 [55.83]
2.100 [53.34]
2.598 [65.99]
2.500 [63.50]
Housing
Part No.
104482-1
104482-2
104482-3
104482-4
104482-5
104482-6
104482-7
104482-8
104482-9
1-104482-0
1-104482-1
1-104482-2
1-104482-3
1-104482-4
1-104482-5
1-104482-6
1-104482-7
1-104482-8
1-104482-9
2-104482-0
5
240
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Short Point Wire-Applied Housings, Double-Row, Polarized, .100 x .100
[2.54 x 2.54] Centerline
A
Material:
Black thermoplastic, flame retardant,
94V-0 rated
.049
[1.24]
.049
[1.24] 2 Plc.
X
Related Product Data:
Performance Characteristics—
page 238
Contacts—page 239
Mateable Headers—pages 121, 122,
153-155
.100
[2.54]
.100
[2.54]
.600
[15.24]
.095
[2.41]
.036
[0.91]
.198
[5.03]
.100
[2.54]
.100
[2.54] Typ.
B
0.72
[1.83]
X
Section X-X
Technical Documents (page 294296):
Product Specification 108-1472,
108-25027
Application Specification
114-25038
No.of
Pos.
8
10
12
14
18
20
26
30
38
50
52
54
64
Dimensions
A
B
.398 [10.11]
.300 [7.62]
.498 [12.65]
.400 [10.16]
.598 [15.19]
.500 [12.70]
.698 [17.73]
.600 [15.24]
.898 [22.81]
.800 [20.32]
.998 [25.35]
.900 [22.86]
1.298 [32.97]
1.200 [30.48]
1.498 [38.05]
1.400 [35.56]
1.898 [48.21]
1.800 [45.72]
2.498 [63.45]
2.400 [60.96]
2.598 [65.99]
2.500 [63.50]
2.698 [68.53]
2.600 [66.04]
3.198 [81.23]
3.100 [78.74]
Housing
Part No.
104483-1
1-104483-1
1-104483-2
104483-9
104483-2
104483-3
104483-4
104483-5
104483-6
1-104483-3
1-104483-0
104483-7
104483-8
Note: Other sizes can be made available on request.
5
241
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Interconnection System
Product Facts
5
■
Receptacle assemblies mate
with .025 [0.64] sq. posts;
mating post length is .200
[5.08] min., .250 [6.35] max.
■
Proven AMPMODU receptacle
contact design; dual cantilever
beams, built-in antioverstress, completely
enclosed “box” design,
standard or high-pressure
■
Insulation displacement
technology
■
Two contact sizes for
terminating 30-22 AWG [0.050.3 mm2] wire range; .054
[1.37] max. insulation diameter with an insulation wall
thickness of .015 [0.38] max.
■
Choice of gold duplex or tin
plated contacts
■
Interchangeable crimp snap-in
pin and receptacle contacts
available
■
Housing sizes 2 through
25 positions, single-row .100
[2.54] centers
■
Colors also available
■
Plain housings are end-to-end
and/or back-to-back stackable
for open pin field applications
■
Optional header with
“swaged tail” feature helps
prevent movement prior to
flow soldering
■
Integral latch provides
positive retention between
header and receptacle
housing
■
Coupling shrouds permit
ganging of smaller connectors
with guide ribs to form larger
single- or double-row latching
connectors
■
Mass terminating tooling
provides lowest applied cost
for most production needs
■
SMT and SMT compatible,
high-temp headers available
■
■
The AMPMODU MTE
Interconnection System
offers both wire-to-board
and wire-to-wire connectors
using .025 [0.64] sq. post
technology.
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
The AMPMODU MTE
Interconnection System
consists of single-row
housings with contacts
preloaded on .100 [2.54]
centers. Housings are
furnished with contacts
partially inserted, leaving
the termination areas
exposed. Final contact
insertion is accomplished
automatically by Tyco
Electronics application
equipment, and manually
when terminated with the
Tyco Electronics pistol grip
hand tool.
Certified by Canadian
Standards
Association,
File No. LR7189
The heart of the system is
the insulation displacement
contact design, featured in
both pin and receptacle
contacts. The receptacle
contact, available in either
standard or high-pressure,
features dual cantilever
beams in an enclosed “box.”
The post stop helps prevent
a mating post from
disturbing the wire
termination and also limits
the mating depth of a long
post to protect a wrap-type
termination at the base of
the post. The forward
contact stop helps prevent
contact overinsertion prior
to termination. All contacts
are furnished on carrier
strips which are interlocked
for stability and positive
location during termination.
Single-row housings are
available in sizes 2 through
25 positions. Included are
three styles of receptacle
housings—plain, polarized/
latching and ribbed and two
styles of pin housings,
shrouded with polarizing/
Performance
Specifications
Electrical Characteristics
Contact Current Rating—3 amperes
for single contact in free air (Amperage
could vary due to ambient temperature,
wire size and duty cycles.)
Contact Termination
Resistance—15 milliohms (max.)
Dielectric Withstanding Voltage—
At Sea Level–600 VAC, rms
At 70,000 Ft. [21 336 m]–225 VAC, rms
Insulation Resistance—
5,000 megohms (min.)
Environmental Characteristics
Operating Temperature—
-65°C to +105°C
Vibration—15 G’s (gold), 10 G’s (tin)
Physical Shock—50 G’s
Industrial Mixed Flow Gasing—
Class 1 (20 days) (gold)
Product Specification
108-25034
Application Specification
114-25026
242
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Interconnection System (Continued)
Wire-to-Board
Receptacle Assemblies
with Guide Ribs
(See pages 249 & 250)
High-Temp Headers,
Polarized/Latching, Straight
and Right Angle Post,
with or without Holddown
(See pages 266 thru 268)2
Receptacle Assemblies
Polarized/Latching
(See pages 247 & 248)
Double-Row Coupling
Shroud (See page 258)
Receptacle
Assemblies,
Polarized/Latching
(See pages 247 & 248)
AMPMODU Shrouded
Headers, Double-Row,
Straight or Right Angle
Post1 (See pages
135-138, 141, 142,
144-146, 148-150 & 166)
Headers,
Polarized/Latching,
Straight Post, with or
without Swaged Tail
(See pages 261 & 262)2
Headers,
Polarized/Latching,
Right Angle Post, with
or without Holddown
(See pages 263 & 264)
Receptacle Assemblies Plain
(See pages 245 and 246)
High Pressure Receptacle Assemblies,
Plain (See page 251)
Receptacle Assemblies
with Guide Ribs
(See pages 249 & 250)
Receptacle Contact,
Insulation Displacement
(Used in all
Receptacle Assemblies)
1
1
2
Single-Row Coupling
Shroud (See page 257)
AMPMODU Breakaway Headers,
Single- or Double-Row, Straight
or Right–Angle Post, with or
without Board Retention Feature
(See pages 101 thru 114)
Mating AMPMODU Double-Row Shrouded Header Assemblies must have .318 [8.08] mating post length and .150 [3.81] dimension from centerline of last
post to inside of end shroud wall.
Surface Mount Right-Angle and Vertical Headers are also available (see pages 269 and 270)
5
243
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Interconnection System (Continued)
Wire-to-Wire
Pin Assemblies, Shrouded
Polarized/Latching
(See pages 253 & 254)
Receptacle Assemblies,
Polarized/Latching
(See pages 247 & 248)
Receptacle Contact,
Insulation Displacement
(Used in all
Receptacle Assemblies)
Pin Contact,
Insulation
Displacement
(Used in all Pin
Assemblies)
Pin Assemblies
with Guide Ribs (See
pages 255 & 256)
Panel Mount
Pin Shroud
(See page 259)
Receptacle Assemblies Single-Row
with Guide Ribs
Coupling
(See pages 249 & 250) Shroud (See
page 257)
Crimp Snap-In
Receptacle Contact
(Used with Unloaded
Housings—
See page 272)
Crimp Snap-In Pin
Contact (Used with
Unloaded Housings—
See page 273)
Note: For wire-to-wire applications shown above, all pin and receptacle assembly combinations are intermateable.
5
244
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Receptacle Assemblies—Plain, Single-Row, .100 [2.54] Centerine
Receptacle Contacts
(See Note 1)
.520
[13.21]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are
recommended when using the
Tyco Electronics Manual Pistol
Grip Tool.
1.120
[28.45]
.600
[15.24]
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Contacts—Phosphor Bronze,
plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] bright
tin-lead over .000050 [0.00127] nickel
on entire contact
Note: Insulation displacement contacts
accept an insulation diameter of .030 [0.76]
min. to .054 [1.37] max. with an
insulation wall thickness of .015 [0.38]
max. Mating post length for preloaded
housings is .200 [5.08] min., .250 [6.35]
max.
B
Typ.
A
Position No. 1 Indicator
(Farside)
.100
[2.54] Typ.
.098
[2.49]
Related Product Data:
Mateable AMPMODU Products:
Breakaway Headers—pages 101114, 117-124 (with .230 mating length)
Reeled Breakaway Headers—
pages 115-116 (with .230 mating
length)
Machine Applied Bandolier
Posts—page 180
Single- or Double-Row Shrouded
Headers with .066 [1.68] End
Dimension—pages 118, 121, 129-134,
139, 140, 143, 147, 149, 150, 162-165
Interchangeable Crimp Contacts
(Short Point)–page 272
Application Tooling—pages 291, 292
Performance Specifications—
page 242
Technical Documents (page 295,
296):
Product Specification 108-25034
Application Specification
114-25026
5
These receptacle assemblies
with plain housings can be
stacked end-to-end and/or sideto-side for single or double-row
connections to an open pin field
with a .100 [2.54] centerline grid.
245
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Receptacle Assemblies—Strip Form Plain,
Single-Row, .100 [2.54] Centerline (Continued)
Housing
Quantities
Per Strip
B
Segment
.198 [5.03]
10
.298 [7.57]
8
.398 [10.11]
5
.498 [12.65]
4
.598 [15.19]
4
.698 [17.73]
2
.798 [20.27]
2
.898 [22.81]
2
.998 [23.35]
2
1.098 [27.89]
2
1.198 [30.43]
2
Dimensions
No. of
Pos.
A
2
3
4
5
6
7
8
9
10
11
12
2.000 [50.80]
2.400 [60.96]
1.990 [50.55]
1.990 [50.55]
2.390 [60.71]
1.400 [35.56]
1.600 [40.64]
1.800 [45.72]
2.000 [50.80]
2.200 [55.88]
2.400 [60.96]
Strip Form Receptacle Assembly
30-26 AWG [0.05-0.15mm2] Wire
Plating A
Plating B
Plating C
103979-1
103979-2
103979-3
103979-4
103979-5
103979-6
103979-7
103979-8
103979-9
1-103979-0
1-103979-1
103978-1
103978-2
103978-3
103978-4
103978-5
103978-6
103978-7
103978-8
103978-9
1-103978-0
1-103978-1
103977-1
103977-2
103977-3
103977-4
103977-5
103977-6
103977-7
103977-8
103977-9
1-103977-0
1-103977-1
Strip Form Receptacle Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
103976-1
103976-2
103976-3
103976-4
103976-5
103976-6
103976-7
103976-8
103976-9
1-103976-0
1-103976-1
103975-1
103975-2
103975-3
103975-4
103975-5
103975-6
103975-7
103975-8
103975-9
1-103975-0
1-103975-1
103974-1
103974-2
103974-3
103974-4
103974-5
103974-6
103974-7
103974-8
103974-9
1-103974-0
1-103974-1
Unloaded
Housings
103688-1
103688-2
103688-3
103688-4
103688-5
103688-6
103688-7
103688-8
103688-9
1-103688-0
1-103688-1
MTE Receptacle Assemblies—Individual Form Plain,
Single-Row, .100 [2.54] Centerline
No. of
Pos.
Dimensions
B
13
14
15
16
17
18
19
20
21
22
23
24
25
1.298 [32.96]
1.398 [35.51]
1.498 [38.05]
1.598 [40.59]
1.698 [43.13]
1.798 [45.67]
1.898 [48.20]
1.998 [50.75]
2.098 [53.29]
2.198 [55.83]
2.298 [58.37]
2.398 [60.91]
2.498 [63.45]
Individual Receptacle Assembly
30-26 AWG [0.05-0.15mm2] Wire
Individual Receptacle Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
1-103903-2
1-103903-3
1-103903-4
1-103903-5
1-103903-6
1-103903-7
1-103903-8
1-103903-9
2-103903-0
2-103903-1
2-103903-2
2-103903-3
2-103903-4
1-103684-2
1-103684-3
1-103684-4
1-103684-5
1-103684-6
1-103684-7
1-103684-8
1-103684-9
2-103684-0
2-103684-1
2-103684-2
2-103684-3
2-103684-4
1-103685-2
1-103685-3
1-103685-4
1-103685-5
1-103685-6
1-103685-7
1-103685-8
1-103685-9
2-103685-0
2-103685-1
2-103685-2
2-103685-3
2-103685-4
1-103902-2
1-103902-3
1-103902-4
1-103902-5
1-103902-6
1-103902-7
1-103902-8
1-103902-9
2-103902-0
2-103902-1
2-103902-2
2-103902-3
2-103902-4
1-103686-2
1-103686-3
1-103686-4
1-103686-5
1-103686-6
1-103686-7
1-103686-8
1-103686-9
2-103686-0
2-103686-1
2-103686-2
2-103686-3
2-103686-4
1-103687-2
1-103687-3
1-103687-4
1-103687-5
1-103687-6
1-103687-7
1-103687-8
1-103687-9
2-103687-0
2-103687-1
2-103687-2
2-103687-3
2-103687-4
Unloaded
Housings
1-103688-2
1-103688-3
1-103688-4
1-103688-5
1-103688-6
1-103688-7
1-103688-8
1-103688-9
2-103688-0
2-103688-1
2-103688-2
2-103688-3
2-103688-4
Notes: 1. Receptacle assemblies are furnished with strip contacts partially inserted into housing—contacts latched into “preload” windows. Contacts are fully inserted into
housings automatically when terminated with Tyco Electronics application machines, or manually when terminated with AMP pistol grip hand tool.
2. Use Extraction/Lance Reset Tool No. 843477-1 to remove receptacle contacts.
3. Keying plugs are available, see page 272.
5
246
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Receptacle Assemblies—Polarized/Latching,
Single-Row, .100 [2.54] Centerline
Receptacle Contacts
(See Note 1)
.520
[13.21]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are
recommended when using the Tyco
Electronics Manual Pistol Grip
Tool.
1.120
[28.45]
.600
[15.24]
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Contacts—Phosphor Bronze, plated as
follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] bright
tin-lead over .000050 [0.00127] nickel on
entire contact
Note: Insulation displacement contacts
accept an insulation diameter of .030 [0.76]
min. to .054 [1.37] max. with an
insulation wall thickness of .015 [0.38]
max. Mating post length for preloaded
housings is .200 [5.08] min., .250 [6.35]
max.
B
Typ.
A
Position No. 1 Indicator
(Farside)
.100
[2.54] Typ.
.098
[2.49]
Related Product Data:
Mateable AMPMODU Products:
Pin Assemblies
(Polarized/Latching)—
pages 253, 254
Pin Assemblies with Guide
Ribs (installed in Panel Mount
Pin Shroud)—pages 255, 256, 259
Headers (Polarized/Latching)—
pages 261-270
Interchangeable Crimp Contacts
(Short Point)––page 272
Application Tooling—pages 291, 292
Performance Specifications—
page 242
5
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
247
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Receptacle Assemblies—Strip Form Polarized/Latching,
Single-Row, .100 [2.54] Centerline (Continued)
Housing
Quantities
Per Strip
Segment
.198 [5.03]
10
.298 [7.57]
8
.398 [10.11]
5
.498 [12.65]
4
.598 [15.19]
4
.698 [17.73]
2
.798 [20.27]
2
.898 [22.81]
2
.998 [23.35]
2
1.098 [27.89]
2
1.198 [30.43]
2
Dimensions
No. of
Pos.
A
2
3
4
5
6
7
8
9
10
11
12
2.000 [50.80]
2.400 [60.96]
1.990 [50.55]
1.990 [50.55]
2.390 [60.71]
1.400 [35.56]
1.600 [40.64]
1.800 [45.72]
2.000 [50.80]
2.200 [55.88]
2.400 [60.96]
B
Strip Form Receptacle Assembly
30-26 AWG [0.05-0.15mm2] Wire
Plating A
Plating B
Plating C
103961-1
103961-2
103961-3
103961-4
103961-5
103961-6
103961-7
103961-8
103961-9
1-103961-0
1-103961-1
103960-1
103960-2
103960-3
103960-4
103960-5
103960-6
103960-7
103960-8
103960-9
1-103960-0
1-103960-1
103959-1
103959-2
103959-3
103959-4
103959-5
103959-6
103959-7
103959-8
103959-9
1-103959-0
1-103959-1
Strip Form Receptacle Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
103958-1
103958-2
103958-3
103958-4
103958-5
103958-6
103958-7
103958-8
103958-9
1-103958-0
1-103958-1
103957-1
103957-2
103957-3
103957-4
103957-5
103957-6
103957-7
103957-8
103957-9
1-103957-0
1-103957-1
103956-1
103956-2
103956-3
103956-4
103956-5
103956-6
103956-7
103956-8
103956-9
1-103956-0
1-103956-1
Unloaded
Housings
104257-1
104257-2
104257-3
104257-4
104257-5
104257-6
104257-7
104257-8
104257-9
1-104257-0
1-104257-1
MTE Receptacle Assemblies—Individual Form Polarized/Latching,
Single-Row, .100 [2.54] Centerline
No. of
Pos.
Dimensions
B
13
14
15
16
17
18
19
20
21
22
23
24
25
1.298 [32.96]
1.398 [35.51]
1.498 [38.05]
1.598 [40.59]
1.698 [43.13]
1.798 [45.67]
1.898 [48.20]
1.998 [50.75]
2.098 [53.29]
2.198 [55.83]
2.298 [58.37]
2.398 [60.91]
2.498 [63.45]
Individual Receptacle Assembly
30-26 AWG [0.05-0.15mm2] Wire
Individual Receptacle Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
1-103897-2
1-103897-3
1-103897-4
1-103897-5
1-103897-6
1-103897-7
1-103897-8
1-103897-9
2-103897-0
2-103897-1
2-103897-2
2-103897-3
2-103897-4
1-103640-2
1-103640-3
1-103640-4
1-103640-5
1-103640-6
1-103640-7
1-103640-8
1-103640-9
2-103640-0
2-103640-1
2-103640-2
2-103640-3
2-103640-4
1-103641-2
1-103641-3
1-103641-4
1-103641-5
1-103641-6
1-103641-7
1-103641-8
1-103641-9
2-103641-0
2-103641-1
2-103641-2
2-103641-3
2-103641-4
1-103734-2
1-103734-3
1-103734-4
1-103734-5
1-103734-6
1-103734-7
1-103734-8
1-103734-9
2-103734-0
2-103734-1
2-103734-2
2-103734-3
2-103734-4
1-103644-2
1-103644-3
1-103644-4
1-103644-5
1-103644-6
1-103644-7
1-103644-8
1-103644-9
2-103644-0
2-103644-1
2-103644-2
2-103644-3
2-103644-4
1-103645-2
1-103645-3
1-103645-4
1-103645-5
1-103645-6
1-103645-7
1-103645-8
1-103645-9
2-103645-0
2-103645-1
2-103645-2
2-103645-3
2-103645-4
Unloaded
Housings
1-104257-2
1-104257-3
1-104257-4
1-104257-5
1-104257-6
1-104257-7
1-104257-8
1-104257-9
2-104257-0
2-104257-1
2-104257-2
2-104257-3
2-104257-4
Notes: 1. Receptacle assemblies are furnished with strip contacts partially inserted into housing—contacts latched into “preload” windows. Contacts are fully inserted into
housings automatically when terminated with AMP application machines, or manually when terminated with AMP pistol grip hand tool.
2. Use Extraction/Lance Reset Tool No. 843477-1 to remove receptacle contacts.
3. Keying plugs are available, see page 272.
5
248
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Receptacle Assemblies—Guide Ribs,
Single-Row, .100 [2.54] Centerline
Receptacle Contacts
(See Note 1)
.520
[13.21]
1.120
[28.45]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are recommended
when using the Tyco Electronics
Manual Pistol Grip Tool.
.600
[15.24]
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Contacts—Phosphor Bronze,
plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] bright
tin-lead over .000050 [0.00127] nickel
on entire contact
Note: Insulation displacement contacts
accept an insulation diameter of .030 [0.76]
min. to .054 [1.37] max. with an
insulation wall thickness of .015 [0.38]
max. Mating post length for preloaded
housings is .200 [5.08] min., .250 [6.35]
max.
B
Typ.
A
Position No. 1 Indicator
(Farside)
.100
[2.54] Typ
.098
[2.49]
Related Product Data:
Coupling Shrouds used with:
Single-Row—page 257
Double-Row—page 258
Mateable AMPMODU Products (with
Receptacle Assemblies Installed
in Single-Row Coupling Shrouds):
Pin Assemblies (Polarized/
Latching)—pages 253, 254
Pin Assemblies with Guide Ribs
(installed in Panel Mount Pin
Shroud)—pages 255, 256, 259
Headers (Polarized/Latching)—
pages 261-270
Mateable AMPMODU Products (with
Receptacle Assemblies Installed
in Double-Row Coupling Shrouds):
Headers, Shrouded, Double-Row
(.318 [8.08] mating post length,
.150 [3.81] end dimension)—pages
135-138, 141, 142, 144, 145, 146,
148-150, 166
Interchangeable Crimp Contacts—
(Short Point)—page 272
Application Tooling—pages 291, 292
Performance Specifications—page 242
5
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
249
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Receptacle Assemblies—Strip Form with Guide Ribs,
Single-Row, .100 [2.54] Centerline (Continued)
Housing
Quantities
Per
Strip
B
Segment
.198 [5.03]
10
.298 [7.57]
8
.398 [10.11]
5
.498 [12.65]
4
.598 [15.19]
4
.698 [17.73]
2
.798 [20.27]
2
.898 [22.81]
2
.998 [23.35]
2
1.098 [27.89]
2
1.198 [30.43]
2
Dimensions
No. of
Pos.
A
2
3
4
5
6
7
8
9
10
11
12
2.000 [50.80]
2.400 [60.96]
1.990 [50.55]
1.990 [50.55]
2.390 [60.71]
1.400 [35.56]
1.600 [40.64]
1.800 [45.72]
2.000 [50.80]
2.200 [55.88]
2.400 [60.96]
Strip Form Receptacle Assembly
30-26 AWG [0.05-0.15mm2] Wire
Plating A
Plating B
Plating C
103973-1
103973-2
103973-3
103973-4
103973-5
103973-6
103973-7
103973-8
103973-9
1-103973-0
1-103973-1
103972-1
103972-2
103972-3
103972-4
103972-5
103972-6
103972-7
103972-8
103972-9
1-103972-0
1-103972-1
103971-1
103971-2
103971-3
103971-4
103971-5
103971-6
103971-7
103971-8
103971-9
1-103971-0
1-103971-1
Strip Form Receptacle Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
103970-1
103970-2
103970-3
103970-4
103970-5
103970-6
103970-7
103970-8
103970-9
1-103970-0
1-103970-1
103969-1
103969-2
103969-3
103969-4
103969-5
103969-6
103969-7
103969-8
103969-9
1-103969-0
1-103969-1
103968-1
103968-2
103968-3
103968-4
103968-5
103968-6
103968-7
103968-8
103968-9
1-103968-0
1-103968-1
Unloaded
Housings
103648-1
103648-2
103648-3
103648-4
103648-5
103648-6
103648-7
103648-8
103648-9
1-103648-0
1-103648-1
MTE Receptacle Assemblies—Individual Form with Guide Ribs,
Single-Row, .100 [2.54] Centerline
No. of
Pos.
Dimensions
B
13
14
15
16
17
18
19
20
21
22
23
24
25
1.298 [32.96]
1.398 [35.51]
1.498 [38.05]
1.598 [40.59]
1.698 [43.13]
1.798 [45.67]
1.898 [48.20]
1.998 [50.75]
2.098 [53.29]
2.198 [55.83]
2.298 [58.37]
2.398 [60.91]
2.498 [63.45]
Individual Receptacle Assembly
30-26 AWG [0.05-0.15mm2] Wire
Individual Receptacle Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
1-103901-2
1-103901-3
1-103901-4
1-103901-5
1-103901-6
1-103901-7
1-103901-8
1-103901-9
2-103901-0
2-103901-1
2-103901-2
2-103901-3
2-103901-4
1-103649-2
1-103649-3
1-103649-4
1-103649-5
1-103649-6
1-103649-7
1-103649-8
1-103649-9
2-103649-0
2-103649-1
2-103649-2
2-103649-3
2-103649-4
1-103650-2
1-103650-3
1-103650-4
1-103650-5
1-103650-6
1-103650-7
1-103650-8
1-103650-9
2-103650-0
2-103650-1
2-103650-2
2-103650-3
2-103650-4
1-103900-2
1-103900-3
1-103900-4
1-103900-5
1-103900-6
1-103900-7
1-103900-8
1-103900-9
2-103900-0
2-103900-1
2-103900-2
2-103900-3
2-103900-4
1-103651-2
1-103651-3
1-103651-4
1-103651-5
1-103651-6
1-103651-7
1-103651-8
1-103651-9
2-103651-0
2-103651-1
2-103651-2
2-103651-3
2-103651-4
1-103652-2
1-103652-3
1-103652-4
1-103652-5
1-103652-6
1-103652-7
1-103652-8
1-103652-9
2-103652-0
2-103652-1
2-103652-2
2-103652-3
2-103652-4
Unloaded
Housings
1-103648-2
1-103648-3
1-103648-4
1-103648-5
1-103648-6
1-103648-7
1-103648-8
1-103648-9
2-103648-0
2-103648-1
2-103648-2
2-103648-3
2-103648-4
Notes: 1. Receptacle assemblies are furnished with strip contacts partially inserted into housing—contacts latched into “preload” windows. Contacts are fully
inserted into housings automatically when terminated with AMP application machines, or manually when terminated with AMP pistol grip hand tool.
2. Use Extraction/Lance Reset Tool No. 843477-1 to remove receptacle contacts.
3. Keying plugs are available, see page 272.
5
250
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE High Pressure Receptacle Assemblies—Plain,
Single-Row, .100 [2.54] Centerline
Receptacle Contacts
(See Note 1)
.520
[13.21]
1.120
[28.45]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are
recommended when using the
Tyco Electronics Manual Pistol
Grip Tool.
.600
[15.24]
Material and Finish:
B
Typ.
Housing—Black thermoplastic,
94V-0 rated
Contacts—Phosphor Bronze, duplex
plated .000030 [0.00076] gold on
contact area, .000050 [0.00127] min.
tin-lead in crimp area, with entire contact
underplated .000050 [0.00127] nickel
Note: Insulation displacement contacts
accept an insulation diameter of .030 [0.76]
min. to .054 [1.37] max. with an
insulation wall thickness of .015 [0.38]
max. Mating post length for preloaded
housings is .200 [5.08] min., .250 [6.35]
max.
A
Position No. 1 Indicator
(Farside)
.100
[2.54] Typ.
.098
[2.49]
Related Product Data:
Mateable AMPMODU Products:
Breakaway Headers—pages 101114, 117-124 (with .230 mating length)
Reeled Breakaway Headers—
pages 115-116 (with .230 mating
length)
Machine Applied Bandolier
Posts—page 180
Application Tooling—pages 291, 292
Performance Specifications—
page 242
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
No. of
.
Pos
A
B
Housings
Quantites Per
Strip Segment
2
3
4
5
6
7
8
9
10
11
12
1.980 [50.29]
1.490 [37.85]
1.990 [50.55]
1.990 [50.55]
2.390 [60.71]
1.400 [35.56]
1.600 [40.64]
1.800 [45.72]
2.000 [50.80]
2.200 [55.88]
2.400 [60.96]
.198 [5.03]
.298 [7.57]
.398 [10.11]
.498 [12.65]
.598 [15.19]
.698 [17.73]
.798 [20.27]
.898 [22.81]
.998 [23.35]
1.098 [27.89]
1.198 [30.43]
10
5
5
4
4
2
2
2
2
2
2
Dimensions
Strip Form
Receptacle
Assembly
30-26 AWG
[.05-.15mm2] Wire
104438-1
104438-2
104438-3
104438-4
104438-5
104438-6
104438-7
104438-8
104438-9
1-104438-0
1-104438-1
Strip Form
Receptacle
Assembly
26-22 AWG
[.12-.30mm2] Wire
104439-1
104439-2
104439-3
104439-4
104439-5
104439-6
104439-7
104439-8
104439-9
1-104439-0
1-104439-1
5
Notes: 1. Receptacle assemblies are furnished with strip contacts partially inserted into housing—contacts latched
into “preload” windows. Contacts are fully inserted into housings automatically when terminated with AMP
application machines, or manually when terminated with AMP pistol grip hand tool.
2. High pressure receptacle contacts can be made available in other housing styles and position sizes.
Contact your Tyco Electronics sales representative.
251
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE High Pressure Receptacle Assemblies – Guide Ribs
Receptacle Contacts
(See Note 1)
.520
[13.21]
Photo 5527
1.120
[28.45]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are
recommended when using the
Tyco Electronics Manual Pistol
Grip Tool.
.600
[15.24]
B
Typ.
Material and Finish:
A
Housing––Thermoplastic, ColorBlack, 94V-0 rated
Position No. 1 Indicator
(Farside)
Contacts––Phosphor Bronze,
Duplex plated .000030 [0.00076] gold
on contact area .000100 [0.00254] min.
tin-lead on crimp area, with entire post
under-plated .000050 [0.00127] nickel.
.100
[2.54] Typ
Related Product Data:
Coupling Shrouds used with:
Single-Row—page 257
Double-Row—page 258
Mateable AMPMODU Products
(with Receptacle Assemblies
Installed in Single-Row Coupling
Shrouds):
Pin Assemblies (Polarized/
Latching)—pages 253, 254
Pin Assemblies with Guide Ribs
(installed in Panel Mount Pin
Shroud)—pages 255, 256, 259
Headers (Polarized/Latching)—
pages 261-270
Mateable AMPMODU Products
(with Receptacle Assemblies
Installed in Double-Row Coupling
Shrouds):
Headers, Shrouded, Double-Row
(.318 [8.08] mating post length,
.150 [3.81] end dimension)—
pages 135, 137, 141, 145, 146, 148150, 166
Application Tooling—pages 291, 292
Performance Specifications—
page 242
Technical Documents (pages
295, 296):
5
Product Specification
108-25034
Application Specification
114-25026
.098
[2.49]
No. of
.
Pos
A
B
Housings
Quantites Per
Strip Segment
2
3
4
5
6
7
8
9
10
11
12
1.980 [50.29]
1.490 [37.85]
1.990 [50.55]
1.990 [50.55]
2.390 [60.71]
1.400 [35.56]
1.600 [40.64]
1.800 [45.72]
2.000 [50.80]
2.200 [55.88]
2.400 [60.96]
.198 [5.03]
.298 [7.57]
.398 [10.11]
.498 [12.65]
.598 [15.19]
.698 [17.73]
.798 [20.27]
.898 [22.81]
.998 [23.35]
1.098 [27.89]
1.198 [30.43]
10
5
5
4
4
2
2
2
2
2
2
Dimensions
Strip Form
Receptacle
Assembly
30-26 AWG
[.05-.15mm2] Wire
147396-1
147396-2
147396-3
147396-4
147396-5
147396-6
147396-7
147396-8
147396-9
1-147396-0
1-147396-1
Strip Form
Receptacle
Assembly
26-22 AWG
[.12-.30mm2] Wire
147030-3
147030-4
147030-1
147030-2
147030-5
147030-6
147030-7
147030-8
147030-9
1-147030-0
1-147030-1
252
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Pin Assemblies, Shrouded—Polarized/Latching,
Single-Row, .100 [2.54] Centerline
Pin Contacts
(See Note 1)
.520
[13.21]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are
recommended when using the
Tyco Electronics Manual Pistol
Grip Tool.
1.470
[37.34]
.950
[24.13]
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Contacts—Phosphor Bronze, plated as
follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] bright
tin-lead over .000050 [0.00127] nickel
on entire contact
Note: Insulation displacement contacts
accept an insulation diameter of .030 [0.76]
min. to .054 [1.37] max. with an
insulation wall thickness of .015 [0.38]
max.
B
Typ.
Position No. 1
Indicator
A
.260
[6.60]
.100
[2.54] Typ.
.200
[5.08]
Related Product Data:
Mateable AMPMODU Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—pages 249, 250,
252, 257
Interchangeable Crimp Contacts—
page 273
Application Tooling—pages 291, 292
Performance Specifications—
page 242
5
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
253
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Pin Assemblies, Shrouded—Strip Form Polarized/Latching,
Single-Row, .100 [2.54] Centerline (Continued)
Housing
Quantities
Per
Strip
B
Segment
.295 [7.49]
8
.395 [10.03]
5
.495 [12.57]
4
.595 [15.11]
4
.695 [17.65]
2
.795 [20.19]
3
.895 [22.73]
2
.995 [25.27]
2
1.095 [27.81]
2
1.195 [30.35]
2
1.295 [32.89]
2
Dimensions
No. of
Pos.
A
2
3
4
5
6
7
8
9
10
11
12
2.360 [59.94]
1.980 [50.29]
1.980 [50.29]
2.380 [60.45]
1.390 [35.31]
2.390 [60.71]
1.790 [45.47]
1.990 [50.57]
2.190 [55.63]
2.390 [60.71]
2.590 [65.79]
Strip Form Pin Assembly
30-26 AWG [0.05-0.15mm2] Wire
Plating A
Plating B
Plating C
103949-1
103949-2
103949-3
103949-4
103949-5
103949-6
103949-7
103949-8
103949-9
1-103949-0
1-103949-1
103948-1
103948-2
103948-3
103948-4
103948-5
103948-6
103948-7
103948-8
103948-9
1-103948-0
1-103948-1
103947-1
103947-2
103947-3
103947-4
103947-5
103947-6
103947-7
103947-8
103947-9
1-103947-0
1-103947-1
Strip Form Pin Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
103946-1
103946-2
103946-3
103946-4
103946-5
103946-6
103946-7
103946-8
103946-9
1-103946-0
1-103946-1
103945-1
103945-2
103945-3
103945-4
103945-5
103945-6
103945-7
103945-8
103945-9
1-103945-0
1-103945-1
103944-1
103944-2
103944-3
103944-4
103944-5
103944-6
103944-7
103944-8
103944-9
1-103944-0
1-103944-1
Unloaded
Housings
103653-1
103653-2
103653-3
103653-4
103653-5
103653-6
103653-7
103653-8
103653-9
1-103653-0
1-103653-1
MTE Pin Assemblies, Shrouded—Individual Form Polarized/Latching,
Single-Row, .100 [2.54] Centerline
No. of
Pos.
Dimensions
B
13
14
15
16
17
18
19
20
21
22
23
24
25
1.395 [35.43]
1.495 [37.97]
1.595 [40.51]
1.695 [43.05]
1.795 [45.59]
1.895 [48.13]
1.995 [50.67]
2.095 [53.21]
2.195 [55.75]
2.295 [58.29]
2.395 [60.83]
2.495 [63.37]
2.595 [65.91]
Individual Pin Assembly
30-26 AWG [0.05-0.15mm2] Wire
Individual Pin Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
1-103894-2
1-103894-3
1-103894-4
1-103894-5
1-103894-6
1-103894-7
1-103894-8
1-103894-9
2-103894-0
2-103894-1
2-103894-2
2-103894-3
2-103894-4
1-103658-2
1-103658-3
1-103658-4
1-103658-5
1-103658-6
1-103658-7
1-103658-8
1-103658-9
2-103658-0
2-103658-1
2-103658-2
2-103658-3
2-103658-4
1-103659-2
1-103659-3
1-103659-4
1-103659-5
1-103659-6
1-103659-7
1-103659-8
1-103659-9
2-103659-0
2-103659-1
2-103659-2
2-103659-3
2-103659-4
1-103893-2
1-103893-3
1-103893-4
1-103893-5
1-103893-6
1-103893-7
1-103893-8
1-103893-9
2-103893-0
2-103893-1
2-103893-2
2-103893-3
2-103893-4
1-103660-2
1-103660-3
1-103660-4
1-103660-5
1-103660-6
1-103660-7
1-103660-8
1-103660-9
2-103660-0
2-103660-1
2-103660-2
2-103660-3
2-103660-4
1-103661-2
1-103661-3
1-103661-4
1-103661-5
1-103661-6
1-103661-7
1-103661-8
1-103661-9
2-103661-0
2-103661-1
2-103661-2
2-103661-3
2-103661-4
Unloaded
Housings
1-103653-2
1-103653-3
1-103653-4
1-103653-5
1-103653-6
1-103653-7
1-103653-8
1-103653-9
2-103653-0
2-103653-1
2-103653-2
2-103653-3
2-103653-4
Notes: 1. Pin assemblies are furnished with strip contacts partially inserted into housing—contacts latched into “preload” windows. Contacts are fully inserted
into housings automatically when terminated with AMP application machines, or manually when terminated with AMP pistol grip hand tool.
2. Use Extraction/Lance Reset Tool No. 843477-1 to remove pin contacts.
5
254
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Pin Assemblies—Guide Ribs,
Single-Row, .100 [2.54] Centerline
Pin Contacts
(See Note 1)
.520
[13.21]
1.120
[28.45]
Preassembled housings in strip
form are available in positions
2 thru 12. For ease of handling,
positions 2 thru 5 are
recommended when using the
Tyco Electtronics Manual Pistol
Grip Tool.
.600
[15.24]
B
Typ.
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Contacts—Phosphor Bronze,
plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000050
[0.00127] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] bright
tin-lead over .000050 [0.00127] nickel
on entire contact
Note: Insulation displacement contacts
accept an insulation diameter of .030 [0.76]
min. to .054 [1.37] max. with an
insulation wall thickness of .015 [0.38]
max.
Position No. 1 Indicator
(Farside)
A
.100
[2.54] Typ.
.098
[2.49]
Related Product Data:
Mateable AMPMODU MTE
Products (with Pin Assembly
Installed in Panel Mount Pin
Shroud): pages 259, 260
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single Coupling
Shroud—pages 249, 250, 252, 257
Interchangeable Crimp Contacts
—page 273
Application Tooling—pages 291, 292
Performance Specifications—
page 242
5
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
255
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Pin Assemblies—Strip Form with Guide Ribs,
Single-Row, .100 [2.54] Centerline (Continued)
Housing
Quantities
Per
Strip
B
Segment
0.198 [5.03]
10
0.298 [7.57]
5
0.398 [10.11]
5
0.498 [12.65]
4
0.598 [15.19]
4
0.698 [17.73]
2
0.798 [20.27]
2
0.898 [22.81]
2
0.998 [25.35]
2
1.098 [27.89]
2
1.198 [30.43]
2
Dimensions
No. of
Pos.
A
2
3
4
5
6
7
8
9
10
11
12
1.980 [50.29]
1.490 [37.85]
1.990 [50.55]
1.990 [50.55]
2.390 [60.71]
1.400 [35.56]
1.600 [40.64]
1.800 [45.72]
2.000 [50.80]
2.200 [55.88]
2.400 [60.96]
Strip Form Pin Assembly
30-26 AWG [0.05-0.15mm2] Wire
Plating A
Plating B
Plating C
103955-1
103955-2
103955-3
103955-4
103955-5
103955-6
103955-7
103955-8
103955-9
1-103955-0
1-103955-1
103954-1
103954-2
103954-3
103954-4
103954-5
103954-6
103954-7
103954-8
103954-9
1-103954-0
1-103954-1
103953-1
103953-2
103953-3
103953-4
103953-5
103953-6
103953-7
103953-8
103953-9
1-103953-0
1-103953-1
Strip Form Pin Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
103952-1
103952-2
103952-3
103952-4
103952-5
103952-6
103952-7
103952-8
103952-9
1-103952-0
1-103952-1
103951-1
103951-2
103951-3
103951-4
103951-5
103951-6
103951-7
103951-8
103951-9
1-103951-0
1-103951-1
103950-1
103950-2
103950-3
103950-4
103950-5
103950-6
103950-7
103950-8
103950-9
1-103950-0
1-103950-1
Unloaded
Housings
104503-1
104503-2
104503-3
104503-4
104503-5
104503-6
104503-7
104503-8
104503-9
1-104503-0
1-104503-1
MTE Pin Assemblies—Individual Form with Guide Ribs,
Single-Row, .100 [2.54] Centerline
No. of
Pos.
Dimensions
B
13
14
15
16
17
18
19
20
21
22
23
24
25
1.398 [35.51]
1.498 [38.05]
1.598 [40.59]
1.698 [43.13]
1.798 [45.67]
1.898 [48.20]
1.998 [50.75]
2.098 [53.29]
2.198 [55.83]
2.298 [58.37]
2.398 [60.91]
2.498 [63.45]
2.598 [65.99]
Individual Pin Assembly
30-26 AWG [0.05-0.15mm2] Wire
Individual Pin Assembly
26-22 AWG [0.12-0.3mm2] Wire
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
1-103896-2
1-103896-3
1-103896-4
1-103896-5
1-103896-6
1-103896-7
1-103896-8
1-103896-9
2-103896-0
2-103896-1
2-103896-2
2-103896-3
2-103896-4
1-103657-2
1-103657-3
1-103657-4
1-103657-5
1-103657-6
1-103657-7
1-103657-8
1-103657-9
2-103657-0
2-103657-1
2-103657-2
2-103657-3
2-103657-4
1-103656-2
1-103656-3
1-103656-4
1-103656-5
1-103656-6
1-103656-7
1-103656-8
1-103656-9
2-103656-0
2-103656-1
2-103656-2
2-103656-3
2-103656-4
1-103895-2
1-103895-3
1-103895-4
1-103895-5
1-103895-6
1-103895-7
1-103895-8
1-103895-9
2-103895-0
2-103895-1
2-103895-2
2-103895-3
2-103895-4
1-103655-2
1-103655-3
1-103655-4
1-103655-5
1-103655-6
1-103655-7
1-103655-8
1-103655-9
2-103655-0
2-103655-1
2-103655-2
2-103655-3
2-103655-4
1-103654-2
1-103654-3
1-103654-4
1-103654-5
1-103654-6
1-103654-7
1-103654-8
1-103654-9
2-103654-0
2-103654-1
2-103654-2
2-103654-3
2-103654-4
Unloaded
Housings
1-104503-2
1-104503-3
1-104503-4
1-104503-5
1-104503-6
1-104503-7
1-104503-8
1-104503-9
2-104503-0
2-104503-1
2-104503-2
2-104503-3
2-104503-4
Notes: 1. Pin assemblies are furnished with strip contacts partially inserted into housing—contacts latched into “preload” windows. Contacts are fully inserted
Notes: 1. into housings automatically when terminated with AMP application machines, or manually when terminated with AMP pistol grip hand tool.
2. Use Extraction/Lance Reset Tool No. 843477-1 to remove pin contacts.
5
256
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Coupling Shrouds for MTE Receptacle Assemblies with Guide Ribs
Single-Row
.307
[7.80]
A
Material:
Black thermoplastic, 94V-0 rated
.582
[14.78]
Technical Documents
(pages 295, 296):
Product Specification
108-25034
Application Specification
114-25026
No. of
Pos.
4
5
6
7
8
9
10
11
12
13
14
Dimension
A
.485 [12.32]
.585 [14.86]
.685 [17.40]
.785 [19.94]
.885 [22.48]
.985 [25.02]
1.085 [27.56]
1.185 [30.10]
1.285 [32.64]
1.385 [35.18]
1.485 [37.72]
Single-Row
Coupling Shroud
103680-1
103680-2
103680-3
103680-4
103680-5
103680-6
103680-7
103680-8
103680-9
1-103680-0
1-103680-1
No. of
Pos.
15
16
17
18
19
20
21
22
23
24
25
Dimension
A
1.585 [40.26]
1.685 [42.80]
1.785 [45.34]
1.885 [47.88]
1.985 [50.42]
2.085 [52.96]
2.185 [55.50]
2.285 [58.04]
2.385 [60.58]
2.485 [63.12]
2.585 [65.66]
Single-Row
Coupling Shroud
1-103680-2
1-103680-3
1-103680-4
1-103680-5
1-103680-6
1-103680-7
1-103680-8
1-103680-9
2-103680-0
2-103680-1
2-103680-2
Pin Assemblies with Guide
Ribs, Installed in Panel
Mount Pin Shroud (Refer to
pages 255, 256 & 259)
Pin Assembly,
Shrouded
Polarized/Latching
(Refer to pages
253 & 254)
Receptacle
Assemblies with Guide
Ribs (Refer to pages
249, 250, 252)
Single-Row
Coupling Shroud
Headers, Polarized/Latching,
Straight and Right Angle Post,
with or without Holddown
(See pages 261-270)
Typical Application of Single-Row Coupling Shroud and Mating AMPMODU MTE Products
5
257
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Coupling Shrouds for MTE Receptacle Assemblies with Guide Ribs (Continued)
Double-Row
Material:
.735
[18.67]
Black thermoplastic, 94V-0 rated
Position No. 1
Identification
Technical Documents (pages
295, 296):
A
Product Specification
108-25034
Application Specification
114-25026
No. of
Pos.
8
10
12
14
16
18
20
22
24
26
28
30
32
34
40
50
Dimension
A
.585 [14.86]
.685 [17.40]
.785 [19.94]
.885 [22.48]
.985 [25.02]
1.085 [27.56]
1.185 [30.10]
1.285 [32.64]
1.385 [35.18]
1.485 [37.72]
1.585 [40.26]
1.685 [42.80]
1.785 [45.34]
1.885 [47.88]
2.185 [55.50]
2.685 [68.20]
Double-Row
Coupling Shroud
103681-1
103681-2
103681-3
103681-4
103681-5
104500-1
104500-2
104500-3
104500-4
104500-5
104500-6
104500-7
104500-8
104500-9
1-104500-0
1-104500-1
AMPMODU Shrouded
Headers Double-Row,
Straight or Right–Angle Post1
Double-Row
Coupling Shroud
Receptacle
Assemblies with Guide
Ribs (Refer to pages
249 & 250)
1
1
5
Mating AMPMODU Double-Row Shrouded Headers must have .318 [8.08] mating post length and .150 [3.81] dimension from centerline
of last post to inside of end shroud wall.
Typical Application of Double-Row Coupling Shroud and Mating AMPMODU Products
258
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Panel Mount Pin Shrouds for MTE Pin Assemblies
with Guide Ribs, Single-Row
Material:
.310
[7.87]
Black thermoplastic, 94V-0 rated
A
.250
[6.35]
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
.990
[25.15]
Position No. 1
Identification
.320
[8.13]
.270
[6.86]
.320
[8.13]
B
No. of
Pos.
2
3
4
5
6
7
8
9
10
11
12
13
Dimensions
A
B
.735 [18.67]
.625 [15.88]
.835 [21.21]
.725 [18.42]
.935 [23.75]
.825 [20.96]
1.035 [26.29]
.925 [23.50]
1.135 [28.83]
1.025 [26.04]
1.235 [31.37]
1.125 [28.58]
1.335 [33.91]
1.225 [31.12]
1.435 [36.45]
1.325 [33.66]
1.535 [38.99]
1.425 [36.20]
1.635 [41.53]
1.525 [38.74]
1.735 [44.07]
1.625 [41.28]
1.835 [46.61]
1.725 [43.82]
Panel Mount
Pin Shroud
103682-1
103682-2
103682-3
103682-4
103682-5
103682-6
103682-7
103682-8
103682-9
1-103682-0
1-103682-1
1-103682-2
No. of
Pos.
14
15
16
17
18
19
20
21
22
23
24
25
Dimensions
A
B
1.935 [49.15]
1.825 [46.36]
2.035 [51.69]
1.925 [48.90]
2.135 [54.23]
2.025 [51.44]
2.235 [56.77]
2.125 [53.98]
2.335 [59.31]
2.225 [56.52]
2.435 [61.85]
2.325 [59.06]
2.535 [64.39]
2.425 [61.60]
2.635 [66.93]
2.525 [64.14]
2.735 [69.47]
2.625 [66.68]
2.835 [72.01]
2.725 [69.22]
2.935 [74.55]
2.825 [71.76]
3.035 [77.09]
2.925 [74.30]
Panel Mount
Pin Shroud
1-103682-3
1-103682-4
1-103682-5
1-103682-6
1-103682-7
1-103682-8
1-103682-9
2-103682-0
2-103682-1
2-103682-2
2-103682-3
2-103682-4
5
259
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Panel Mount Pin Shrouds for MTE Pin Assemblies
with Guide Ribs, Single-Row (Continued)
Material:
Black thermoplastic, 94V-0 rated
Technical Documents (pages
295, 296):
Pin Assembly with
Guide Ribs (Refer to
pages 255 & 256)
Product Specification
108-25034
Application Specification
114-25026
Panel Mount
Pin Shroud
Receptacle Assemblies with Guide
Ribs, Installed in
Single-Row Coupling Shroud
(Refer to pages 249, 250, 252 & 277)
Rear of Panel
Receptacle Assembly,
Polarized/Latching (Refer
to pages 247 & 248)
Typical Application of Panel Mount Pin Shroud and Mating AMPMODU Products
5
260
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded Polarized/Latching,
Single-Row .100 [2.54] Centerline
.025 [0.64] Square
Straight Post (With or
Without Swaged Tail)
.535
[13.59]
Swaged Retention Tail
(See Note)
Photo 98184-9
Position No. 1 Indicator
A
Material and Finish:
.230
[5.84]
B
Housing—Black thermoplastic,
94V-0 rated
Posts—Copper alloy, plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000100
[0.00254] min. tin-lead on solder area,
with entire post underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000100
[0.00254] min. tin-lead on solder area,
with entire post underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] tin-lead
over .000050 [0.00127] nickel on entire
post
C
.060
[1.52]
.200
[5.08]
.120
[3.05]
.100
Typ.
[2.54]
.200
Ref.
[5.08]
(Contact Area)
.100
[2.54]
X
.130
[3.30]
.275
[6.98]
.350
[8.89]
X
.060
[1.52]
Section X-X
C
.100*
Typ.
[2.54]
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—
pages 249, 250, 252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
.035±.003
Dia. Typ.
[0.89±0.08]
or
.040±.003
Dia. Typ.
[1.02±0.08]
(for Retention Tails)
Recommended PC Board Hole Layout
*±.003 [±0.08]; tolerances not to accumulate within one connector pattern.
Note: Swaged retention tails are provided in a minimum of two locations per header.
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
5
261
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded Polarized/Latching,
Single-Row .100 [2.54] Centerline (Continued)
Dimensions
Polarized/Latching Header With Swage
No. of
Pos.
A
B
C
Plating A
Plating B
Plating C
2
.300 [7.62]
.220 [5.59]
.100 [2.54]
103908-1
103670-1
103669-1
3
.400 [10.16]
.320 [8.13]
.200 [5.08]
103908-2
103670-2
103669-2
4
.500 [12.70] .420 [10.67]
.300 [7.62]
103908-3
103670-3
103669-3
5
.600 [15.24] .520 [13.21]
.400 [10.16]
103908-4
103670-4
103669-4
6
.700 [17.78] .620 [15.75]
.500 [12.70]
103908-5
103670-5
103669-5
7
.800 [20.32] .720 [18.29]
.600 [15.24]
103908-6
103670-6
103669-6
8
.900 [22.86] .820 [20.83]
.700 [17.78]
103908-7
103670-7
103669-7
9
1.000 [25.40] .920 [23.37]
.800 [20.32]
103908-8
103670-8
103669-8
10 1.100 [27.94] 1.020 [25.91]
.900 [22.86]
103908-9
103670-9
103669-9
11 1.200 [30.48] 1.120 [28.45] 1.000 [25.40]
1-103908-0
1-103670-0
1-103669-0
12 1.300 [33.02] 1.220 [30.99] 1.100 [27.94]
1-103908-1
1-103670-1
1-103669-1
13 1.400 [35.56] 1.320 [33.53] 1.200 [30.48]
1-103908-2
1-103670-2
1-103669-2
14 1.500 [38.10] 1.420 [36.07] 1.300 [33.02]
1-103908-3
1-103670-3
1-103669-3
15 1.600 [40.64] 1.520 [38.61] 1.400 [35.56]
1-103908-4
1-103670-4
1-103669-4
16 1.700 [43.18] 1.620 [41.15] 1.500 [38.10]
1-103908-5
1-103670-5
1-103669-5
17 1.800 [45.72] 1.720 [43.69] 1.600 [40.64]
1-103908-6
1-103670-6
1-103669-6
18 1.900 [48.26] 1.820 [46.23] 1.700 [43.18]
1-103908-7
1-103670-7
1-103669-7
19 2.000 [50.80] 1.920 [48.77] 1.800 [45.72]
1-103908-8
1-103670-8
1-103669-8
20 2.100 [53.34] 2.020 [51.31] 1.900 [48.26]
1-103908-9
1-103670-9
1-103669-9
21 2.200 [55.88] 2.120 [53.85] 2.000 [50.80]
2-103908-0
2-103670-0
2-103669-0
22 2.300 [58.42] 2.220 [56.39] 2.100 [53.34]
2-103908-1
2-103670-1
2-103669-1
23 2.400 [60.96] 2.320 [58.93] 2.200 [55.88]
2-103908-2
2-103670-2
2-103669-2
24 2.500 [63.50] 2.420 [61.47] 2.300 [58.42]
2-103908-3
2-103670-3
2-103669-3
25 2.600 [66.04] 2.520 [64.01] 2.400 [60.96]
2-103908-4
2-103670-4
2-103669-4
Notes: 1.Selectively loaded headers are available, consult Tyco Electronics.
2. Use Keying Tool No. 91417-1 to remove post for keying.
Polarized/Latching Header Without Swage
Plating A
Plating B
Plating C
103735-1
103638-1
103639-1
103735-2
103638-2
103639-2
103735-3
103638-3
103639-3
103735-4
103638-4
103639-4
103735-5
103638-5
103639-5
103735-6
103638-6
103639-6
103735-7
103638-7
103639-7
103735-8
103638-8
103639-8
103735-9
103638-9
103639-9
1-103735-0
1-103638-0
1-103639-0
1-103735-1
1-103638-1
1-103639-1
1-103735-2
1-103638-2
1-103639-2
1-103735-3
1-103638-3
1-103639-3
1-103735-4
1-103638-4
1-103639-4
1-103735-5
1-103638-5
1-103639-5
1-103735-6
1-103638-6
1-103639-6
1-103735-7
1-103638-7
1-103639-7
1-103735-8
1-103638-8
1-103639-8
1-103735-9
1-103638-9
1-103639-9
2-103735-0
2-103638-0
2-103639-0
2-103735-1
2-103638-1
2-103639-1
2-103735-2
2-103638-2
2-103639-2
2-103735-3
2-103638-3
2-103639-3
2-103735-4
2-103638-4
2-103639-4
5
262
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded Latching, Single-Row .100 [2.54] Centerline
With Holddown
.025 [0.64] Square
Right-Angle Post
.535
[13.59]
Position No. 1 Indicator
A
B
.100
[2.54]
C
.060
[1.52]
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Posts—Copper alloy, plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000100
[0.00254] min. tin-lead on solder area,
with entire post underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000100
[0.00254] min. tin-lead on solder area,
with entire post underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] tin-lead
over .000050 [0.00127] nickel on entire
post
.100
Typ.
[2.54]
X
.230
[5.84]
.200
Ref.
[5.08]
(Contact Area)
.200
[5.08]
.365
[9.27]
.275
[6.99]
.130
[3.30]
.120
[3.05]
X
.060
[1.52]
.134±.003
Dia.
[3.40±0.08]
(2 Plc.)
.340±.003
Typ.
[8.64±0.08]
.100*
Typ.
[2.54]
.350
[8.89]
.145
[3.68]
Section X-X
.055±.003
Typ.
[1.40±0.08]
.035±.003
Dia. Typ.
[0.89±0.08]
C
Recommended PC Board Hole Layout
(PC board thickness (for Holddown Feature) is .062±.008 [1.57±0.20])
*±.003 [±0.08]; tolerance not to accumulate within one connector pattern.
Without Holddown
.535
[13.59]
Related Product Data:
Position No. 1 Indicator
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Latching)—pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—
pages 249, 250, 252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
Technical Documents (pages
A
.060
[1.52]
B
C
.100
Typ.
[2.54]
.100
[2.54]
X
.230
[5.84]
.200
Ref.
[5.08]
(Contact Area)
.200 .275
[5.08] [6.99]
.130
[3.30]
.120
[3.05]
.060
[1.52]
X
.350
[8.89]
C
.100*
Typ.
[2.54]
295, 296):
Product Specification
108-25034
Application Specification
114-25026
5
.145
[3.68]
Section X-X
.035±.003
Dia. Typ.
[0.89±0.08]
Recommended PC Board Hole Layout
*±.003 [±0.08]; tolerance not to accumulate within one connector pattern.
263
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded Latching, Single-Row .100 [2.54] Centerline (Continued)
Dimensions
Latching Header With Hold Down
No. of
Pos.
A
B
C
Plating A
Plating B
Plating C
2
.300 [7.62]
.220 [5.59]
.100 [2.54]
103904-1
103673-1
103672-1
3
.400 [10.16]
.320 [8.13]
.200 [5.08]
103904-2
103673-2
103672-2
4
.500 [12.70] .420 [10.67]
.300 [7.62]
103904-3
103673-3
103672-3
5
.600 [15.24] .520 [13.21]
.400 [10.16]
103904-4
103673-4
103672-4
6
.700 [17.78] .620 [15.75]
.500 [12.70]
103904-5
103673-5
103672-5
7
.800 [20.32] .720 [18.29]
.600 [15.24]
103904-6
103673-6
103672-6
8
.900 [22.86] .820 [20.83]
.700 [17.78]
103904-7
103673-7
103672-7
9
1.000 [25.40] .920 [23.37]
.800 [20.32]
103904-8
103673-8
103672-8
10 1.100 [27.94] 1.020 [25.91]
.900 [22.86]
103904-9
103673-9
103672-9
11 1.200 [30.48] 1.120 [28.45] 1.000 [25.40]
1-103904-0
1-103673-0
1-103672-0
12 1.300 [33.02] 1.220 [30.99] 1.100 [27.94]
1-103904-1
1-103673-1
1-103672-1
13 1.400 [35.56] 1.320 [33.53] 1.200 [30.48]
1-103904-2
1-103673-2
1-103672-2
14 1.500 [38.10] 1.420 [36.07] 1.300 [33.02]
1-103904-3
1-103673-3
1-103672-3
15 1.600 [40.64] 1.520 [38.61] 1.400 [35.56]
1-103904-4
1-103673-4
1-103672-4
16 1.700 [43.18] 1.620 [41.15] 1.500 [38.10]
1-103904-5
1-103673-5
1-103672-5
17 1.800 [45.72] 1.720 [43.69] 1.600 [40.64]
1-103904-6
1-103673-6
1-103672-6
18 1.900 [48.26] 1.820 [46.23] 1.700 [43.18]
1-103904-7
1-103673-7
1-103672-7
19 2.000 [50.80] 1.920 [48.77] 1.800 [45.72]
1-103904-8
1-103673-8
1-103672-8
20 2.100 [53.34] 2.020 [51.31] 1.900 [48.26]
1-103904-9
1-103673-9
1-103672-9
21 2.200 [55.88] 2.120 [53.85] 2.000 [50.80]
2-103904-0
2-103673-0
2-103672-0
22 2.300 [58.42] 2.220 [56.39] 2.100 [53.34]
2-103904-1
2-103673-1
2-103672-1
23 2.400 [60.96] 2.320 [58.93] 2.200 [55.88]
2-103904-2
2-103673-2
2-103672-2
24 2.500 [63.50] 2.420 [61.47] 2.300 [58.42]
2-103904-3
2-103673-3
2-103672-3
25 2.600 [66.04] 2.520 [64.01] 2.400 [60.96]
2-103904-4
2-103673-4
2-103672-4
Notes: 1.Selectively loaded headers are available, consult Tyco Electronics.
2. Use Keying Tool No. 91417-1 to remove post for keying.
Latching Header Without Hold Down
Plating A
Plating B
Plating C
103906-1
103635-1
103634-1
103906-2
103635-2
103634-2
103906-3
103635-3
103634-3
103906-4
103635-4
103634-4
103906-5
103635-5
103634-5
103906-6
103635-6
103634-6
103906-7
103635-7
103634-7
103906-8
103635-8
103634-8
103906-9
103635-9
103634-9
1-103906-0
1-103635-0
1-103634-0
1-103906-1
1-103635-1
1-103634-1
1-103906-2
1-103635-2
1-103634-2
1-103906-3
1-103635-3
1-103634-3
1-103906-4
1-103635-4
1-103634-4
1-103906-5
1-103635-5
1-103634-5
1-103906-6
1-103635-6
1-103634-6
1-103906-7
1-103635-7
1-103634-7
1-103906-8
1-103635-8
1-103634-8
1-103906-9
1-103635-9
1-103634-9
2-103906-0
2-103635-0
2-103634-0
2-103906-1
2-103635-1
2-103634-1
2-103906-2
2-103635-2
2-103634-2
2-103906-3
2-103635-3
2-103634-3
2-103906-4
2-103635-4
2-103634-4
5
264
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded Latching, Single-Row .100 [2.54] Centerline
.025 [0.64] Square Straight
Post (With Swaged Tails
and PC Board Orientation)
.535
[13.59]
Swaged Retention Tail
(See Note)
Position No. 1 Indicator
Photo 98184-5
A
.060
[1.52]
(2 Plc.)
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Posts—Copper alloy, plated .000100.000200 [0.00254-0.00508] tin-lead
over .000050 [0.00127] nickel on entire
post
B
C
.120
[3.05]
.070
[1.78]
X
.100
[2.54]
.050
[1.27]
Dia.
.260
[6.60]
.200
[5.08]
.060
[1.52]
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—
pages 249, 250, 252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
X
.050
[1.27]
.100
[2.54]
Typ.
C
.100*
Typ.
[2.54]
.040±.003
Dia. Typ.
[1.02±0.08]
(for Retention Tails)
.230
[5.84]
.065±.003
Dia.
[1.65±0.08]
.130
[3.30]
.135±.003
[3.43±0.08]
.075±.003
[1.91±0.08]
.350
[8.89]
Section X-X
Recommended PC Board Hole Layout
Technical Documents (pages
295, 296):
*±.003 [±0.08]; tolerances not to accumulate within one connector pattern.
Note: Swaged retention tails are provided in a minimum of two locations per header.
Product Specification
108-25034
Application Specification
114-25026
No. of
Pos.
2
3
4
5
6
7
8
9
10
A
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
Dimensions
B
.220 [5.59]
.320 [8.13]
.420 [10.67]
.520 [13.21]
.620 [15.75]
.720 [18.29]
.820 [20.83]
.920 [23.37]
1.020 [25.91]
C
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
Latching
Header
104450-1
104450-2
104450-3
104450-4
104450-5
104450-6
104450-7
104450-8
104450-9
5
265
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, High-Temp, Shrouded Polarized/Latching,
Single-Row .100 [2.54] Centerline
.025 [0.64] Square Straight
Post (With Swaged Tails
and PC Board Orientation)
.535
[13.59]
Swaged Retention Tail
(See Note)
Position No. 1 Indicator
A
Photo 98184-5
B
C
Material and Finish:
Housing—Black thermoplastic,
94V-0 rated
Posts—Copper alloy, duplex plated
.000015 [0.00038] gold on contact area,
.000100-.000200 [0.00254-0.00508]
matte tin-lead on solder tail, with entire
post underplated .000050 [0.00127]
nickel
.060
[1.52]
.230
[5.84]
.100
[2.54]
.200
Ref.
[5.08]
(Contact Area)
X
.262
[6.65]
.120
[3.05]
.060
[1.52]
.200
[5.08]
.100 Typ.
[2.54]
.350
[8.89]
.130
[3.30]
X
Section X-X
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—
pages 249, 250, 252, 257
Receptacle Assemblies (Polarized
Latching)—pages 247, 248
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
.040±.002 Typ.
[1.02±0.05]
.100*
Typ.
[2.54]
.065±.003
[1.65±0.08]
.180±.002
[4.57±0.05]
.040±.003 Dia. Typ.
[1.02±0.08]
Plated-Thru Hole
.135±.003
[3.43±0.08]
.020±.002
[0.51±0.05]
Typ.
Header Profile (Shown for
orientation purposes only)
.075±.003
[1.90±0.08]
Recommended PC Board Hole Layout
(Stencil Thickness = .010 [0.25])
*±.003 [±0.08] tolerance not to accumulate within one connector pattern
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
5
No. of
Pos.
2
3
4
5
6
7
8
9
10
11
12
A
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
Dimensions
B
.220 [5.59]
.320 [8.13]
.420 [10.67]
.520 [13.21]
.620 [15.75]
.720 [18.29]
.820 [20.83]
.920 [23.37]
1.020 [25.91]
1.120 [28.45]
1.220 [30.99]
C
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
Polarized/Latching
Header, High-Temp
104809-1
104809-2
104809-3
104809-4
104809-5
104809-6
104809-7
104809-8
104809-9
1-104809-0
1-104809-1
266
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded High-Temp, Polarized/Latching
(Thru-Hole, SMT Compatible) Single-Row, .100 [2.54] Centerline
.025 [0.64] Square
Straight Post (With or
Without Swaged Tail)
.535
[13.59]
Swaged Retention Tail
(See Note)
.230
[5.84]
Position No. 1 Indicator
A
.060
[1.52]
(2 Plc.)
B
C
.200
Ref.
[5.08]
(Contact Area)
.100
[2.54]
X
.262
[6.65]
Material and Finish:
Housing—Black thermoplastic, high
temperature, 94V-0 rated
Posts—Copper alloy, duplex plated
.000015 [0.00038] gold on contact area,
.000100-.000200 [0.00254-0.00508]
matte tin-lead on solder tail, with entire
post underplated .000050 [0.00127]
nickel
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—pages 249, 250,
252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
.120
[3.05]
.060
[1.52]
.350
[8.89]
.200
[5.08]
X
Section X-X
.100 Typ.
[2.54]
.130
[3.30]
C
.100* Typ.
[2.54]
.040±.002 Typ.
[1.02±0.05]
.180
[4.57]
.035±.003 Dia. Typ.
[0.89±0.08]
Plated-Thru Hole
or
.040±.003 Dia. Typ.
[1.02±0.08]
Plated-Thru Hole
(for Retention Tails)
.020
[0.51]
Typ.
Header Profile (Shown for
orientation purposes only)
Recommended PC Board Hole Layout
(Stencil Thickness = .010 [0.25])
*±.003 [±0.08]; tolerance not to accumulate within one connector pattern.
Note: Swaged retention tails in Holddown versions only. Retention tails are provided in a minimum of two locations
per header.
No. of
Pos.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
A
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.300 [58.42]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
Dimensions
B
.220 [5.59]
.320 [8.13]
.420 [10.67]
.520 [13.21]
.620 [15.75]
.720 [18.29]
.820 [20.83]
.920 [23.37]
1.020 [25.91]
1.120 [28.45]
1.220 [30.99]
1.320 [33.53]
1.420 [36.07]
1.520 [38.61]
1.620 [41.15]
1.720 [43.69]
1.820 [46.23]
1.920 [48.77]
2.020 [51.31]
2.120 [53.85]
2.220 [56.39]
2.320 [58.93]
2.420 [61.47]
2.520 [64.01]
C
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.300 [58.42]
2.400 [60.96]
Straight Header
With Swage
Without Swage
104362-1
104363-1
104362-2
104363-2
104362-3
104363-3
104362-4
104363-4
104362-5
104363-5
104362-6
104363-6
104362-7
104363-7
104362-8
104363-8
104362-9
104363-9
1-104362-0
1-104363-0
1-104362-1
1-104363-1
1-104909-2
1-104910-2
1-104909-3
1-104910-3
1-104909-4
1-104910-4
1-104909-5
1-104910-5
1-104909-6
1-104910-6
1-104909-7
1-104910-7
1-104909-8
1-104910-8
1-104909-9
1-104910-9
2-104909-0
2-104910-0
2-104909-1
2-104910-1
2-104909-2
2-104910-2
2-104909-3
2-104910-3
2-104909-4
2-104910-4
5
Note: Use Keying Tool No. 91417-1 to remove post for keying.
267
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Shrouded High-Temp, Polarized/Latching
(Thru-Hole, SMT Compatible) Single-Row, .100 [2.54] Centerline (Continued)
.025 [0.64] Square
Right-Angle Post (With
Holddown)
.535
[13.59]
Position No. 1 Indicator
Material and Finish:
Housing—Black thermoplastic, high
temperature, 94V-0 rated
Posts—Copper alloy, duplex plated
.000015 [0.00038] gold on contact area,
.000100-.000200 [0.00254-0.00508]
matte tin-lead on solder tail, with entire
post underplated .000050 [0.00127]
nickel
.230
[5.84]
A
.060
[1.52]
(2 Plc.)
B
C
.100 Typ.
[2.54]
.120
[3.05]
.100
[2.54]
X
.200
Ref.
[5.08]
(Contact Area)
.262
[6.65]
.200
[5.08]
.145
[3.68]
.180
[4.57]
.060
[1.52]
X
.350
[8.89]
.145
[3.68]
Section X-X
.093+.003
-.000 Dia.
.093+0.08
2.36
-.000
(2 Plc.)
.093
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with Guide
Ribs (installed in Single-Row
Coupling Shroud)—pages 249, 250,
252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
[
.340±.003
[8.64±0.08]
.035±.003
Dia. Typ.
[0.89±0.08]
Plated-Thru Hole
]
.090±.002
[2.29±0.05]
.100* Typ.
[2.54]
.070±.002 Typ.
[1.78±0.51]
C
.058±.003
[1.47±0.08]
(2 Plc.)
Recommended PC Board
(Stencil Thickness = .010 [0.25])
*±.003 [±0.08]; tolerance is not to accumulate within one connector pattern.
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
5
B
C
Right-Angle
Header
with Hold Down
No. of
Positions
Dimensions
No. of
Positions
A
B
C
Right-Angle
Header
with Hold Down
Dimensions
A
2
.300 [7.62]
.220 [5.59]
.100 [2.54]
104361-1
14
1.500 [38.10]
1.420 [36.07]
1.300 [33.02]
1-104361-3
3
.400 [10.16]
.320 [8.13]
.200 [5.08]
104361-2
15
1.600 [40.64]
1.520 [38.61]
1.400 [35.56]
1-104361-4
4
.500 [12.70]
.420 [10.67]
.300 [7.62]
104361-3
16
1.700 [43.18]
1.620 [41.15]
1.500 [38.10]
1-104361-5
5
.600 [15.24]
.520 [13.21]
.400 [10.16]
104361-4
17
1.800 [45.72]
1.720 [43.69]
1.600 [40.64]
1-104361-6
6
.700 [17.78]
.620 [15.75]
.500 [12.70]
104361-5
18
1.900 [48.26]
1.820 [46.23]
1.700 [43.18]
1-104361-7
7
.800 [20.32]
.720 [18.29]
.600 [15.24]
104361-6
19
2.000 [50.80]
1.920 [48.77]
1.800 [45.72]
1-104361-8
8
.900 [22.86]
.820 [20.83]
.700 [17.78]
104361-7
20
2.100 [53.34]
2.020 [51.31]
1.900 [48.26]
1-104361-9
9
1.000 [25.40]
.920 [23.37]
.800 [20.32]
104361-8
21
2.200 [55.88]
2.120 [53.85]
2.000 [50.80]
2-104361-0
10
1.100 [27.94]
1.020 [25.91]
.900 [22.86]
104361-9
22
2.300 [58.42]
2.220 [56.39]
2.100 [53.34]
2-104361-1
11
1.200 [30.48]
1.120 [28.44]
1.000 [25.40]
1-104361-0
23
2.400 [60.96]
2.320 [58.93]
2.200 [55.88]
2-104361-2
12
1.300 [33.02]
1.220 [30.99]
1.100 [27.94]
1-104361-1
24
2.500 [63.50]
2.420 [61.47]
2.300 [58.42]
2-104361-3
13
1.400 [35.56]
1.320 [33.53]
1.200 [30.48]
1-104361-2
25
2.600 [66.04]
2.520 [64.01]
2.400 [60.96]
2-104361-4
268
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Right-Angle, Polarized/Latching, Surface Mount
.025
[0.64] Typ.
.120
[3.05]
.535
[13.59]
Material and Finish:
Housing—High temperature
thermoplastic, Color - Black
ø.085±.002
[2.16±0.05]
.065 Min Pad on
[1.65] Underside 2 Plc
.140
[3.56]
Position No. 1 Indicator
.133
[3.38]
.070±.002 Typ
[1.78±0.05]
A
Plating A—Duplex plated .000030
[.00076] gold on contact area,
.000100 [.00254] min. tin-lead on
solder area, with entire post
underplated .000050 [.00127]
nickel.
.120
[3.05]
.200
[5.08]
K
.002
[0.05]
(Tangent
of heel)
C
Plating C—.000100 [.00254] tin
lead over .000050 [.00127] nickel
on entire post
D
.076
[1.93]
.190±.001
[4.83±0.02]
2 Plc
+.002
Ø .047 -.003
+0.05
[1.19 -0.07
(Plated thru hole)
.038 2 Plc
[0.97]
]
C
.350
[8.89]
.200
[5.08] Ref
Contact Area
B
K
.262
[6.65]
.136±.001
[3.45±0.02]
2 Plc
.265
[6.73]
.165±.003
[4.19±0.07]
Posts—Copper Alloy, plated as
follows:
Plating B—Duplex plated .000015
[.00038] gold on contact area,
.000100 [.00254] min. tin-lead on
solder area, with entire post
underplated .000050 [.00127]
nickel.
E
.457
[11.61]
Ref
See L
Section K-K
Recommended
PC Board Layout
(Refer to MTE Application Spec.
114-25026 for Stencil Aperture
Layout Using .006 [0.152] or
.008 [0.203] Stencil Thickness)
.288
[7.32]
Ref
.054/.039
[1.37/0.99]
L
.140±.002
[3.56±0.05]
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with
Guide Ribs (installed in SingleRow Coupling Shroud)—
pages 249, 250, 252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
Technical Documents
(pages 295, 296):
Product Specification
108-25034
Application Specification
114-25026
No. of
Pos.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
A
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.300 [58.42]
2.400 [60.96]
2.500 [63.50]
2.600 [66.04]
2.700 [68.58]
B
.220 [5.59]
.320 [8.13]
.420 [10.67]
.520 [13.21]
.620 [15.75]
.720 [18.29]
.820 [20.83]
.920 [23.37]
1.020 [25.91]
1.120 [28.45]
1.220 [30.99]
1.320 [33.53]
1.420 [36.07]
1.520 [38.61]
1.620 [41.15]
1.720 [43.69]
1.820 [46.23]
1.920 [48.77]
2.020 [51.31]
2.120 [53.85]
2.220 [56.39]
2.320 [58.93]
2.420 [61.47]
2.520 [64.01]
Dimensions
C
.100 [2.54]
.200 [5.08]
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
1.900 [48.26]
2.000 [50.80]
2.100 [53.34]
2.200 [55.88]
2.300 [58.42]
2.400 [60.96]
D
.140 [3.56]
.190 [4.83]
.240 [6.10]
.290 [7.37]
.340 [8.64]
.390 [9.91]
.440 [11.18]
.490 [12.45]
.540 [13.72]
.590 [14.99]
.640 [16.26]
.690 [17.53]
.740 [18.80]
.790 [20.07]
.840 [21.34]
.890 [22.61]
.940 [23.88]
.990 [25.15]
1.040 [26.42]
1.090 [27.69]
1.140 [28.96]
1.190 [30.23]
1.240 [31.50]
1.290 [32.77]
E
.290 [7.37]
.390 [9.91]
.490 [12.45]
.590 [14.99]
.690 [17.53]
.790 [20.07]
.890 [22.61]
.990 [25.15]
1.090 [27.69]
1.190 [30.23]
1.290 [32.77]
1.390 [35.31]
1.490 [37.85]
1.590 [40.39]
1.690 [42.93]
1.790 [45.47]
1.890 [48.01]
1.990 [50.55]
2.090 [53.09]
2.190 [55.63]
2.290 [58.17]
2.390 [60.71]
2.490 [63.25]
2.590 [65.79]
Right-Angle Latching SMT Headers
Plating A
Plating B
Plating C
147323-1
147278-1
147324-1
147323-2
147278-2
147324-2
147323-3
147278-3
147324-3
147323-4
147278-4
147324-4
147323-5
147278-5
147324-5
147323-6
147278-6
147324-6
147323-7
147278-7
147324-7
147323-8
147278-8
147324-8
147323-9
147278-9
147324-9
1-147323-0
1-147278-0 1-147324-0
1-147323-1
1-147278-1 1-147324-1
1-147323-2
1-147278-2 1-147324-2
1-147323-3
1-147278-3 1-147324-3
1-147323-4
1-147278-4 1-147324-4
1-147323-5
1-147278-5 1-147324-5
1-147323-6
1-147278-6 1-147324-6
1-147323-7
1-147278-7 1-147324-7
1-147323-8
1-147278-8 1-147324-8
1-147323-9
1-147278-9 1-147324-9
2-147323-0
2-147278-0 2-147324-0
2-147323-1
2-147278-1 2-147324-1
2-147323-2
2-147278-2 2-147324-2
2-147323-3
2-147278-3 2-147324-3
2-147323-4
2-147278-4 2-147324-4
5
269
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MTE Headers, Vertical, Polarized/Latching, Surface Mount
E
.075
[1.90]
.025 Typ.
[0.62]
.535
[13.59]
Material and Finish:
Housing—High temperature
thermoplastic, Color - Black, 94V-0
rated
Posts—Brass, plated as follows:
.313
[7.62]
A
K
.100
[2.54]
Pick and Place Cap
Section K-K
.002
Ø .052±.003
0.05
[1.32±0.07
Plated Thru-Hole
.100 Typ.
[2.54]
.055±.003
[1.40±0.08]
.088±.003
[2.25±0.08]
]
Plating C—.000100 [.00254] tin
lead over .000050 [.00127] nickel
on entire contact/post
Ø .070±.002
[1.78±0.05]
Recommended
PC Board Layout
.113
[2.88]
C
Related Product Data:
Mateable AMPMODU MTE
Products:
Receptacle Assemblies
(Polarized/Latching)—
pages 247, 248
Receptacle Assemblies with
Guide Ribs (installed in SingleRow Coupling Shroud)—
pages 249, 250, 252, 257
Other Mateable Connectors:
Flexible Film Connectors—
Catalog 82007
.227
[5.76]
0.06
[1.53]
D
(Refer to MTE Application Spec.
114-25026 for Stencil Aperature
Layout using .006 [0.152] or .008
[0.203] stencil thickness
Product Specification
108-25034
Application Specification
114-25026
.120
[3.05]
K
.200
[5.08]
Plating B—Duplex plated .000015
[.00038] gold on contact area,
.000100 [.00254] min. tin-lead on
solder area, with entire post
underplated .000050 [.00127]
nickel.
Technical Documents
(pages 295, 296):
.230
[5.84]
B
.025 Typ.
[0.64]
Plating A—Duplex plated .000030
[.00076] gold on contact area,
.000100 [.00254] min. tin-lead on
solder area, with entire post
underplated .000050 [.00127]
nickel.
5
.063
Position No. 1 Indicator [1.52]
Position No. 1
Dimensions
No. of
Pos.
A
2
.300[7.62]
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
.400[10.16]
.500[12.70]
.600[15.24]
.700[17.78]
.800[20.32]
.900[22.86]
1.000[25.40]
1.100[27.94]
1.200[30.48]
1.300[33.02]
1.400[35.56]
1.500[38.10]
1.600[40.64]
1.700[43.18]
1.800[45.72]
1.900[48.26]
2.000[50.80]
2.100[53.34]
2.200[55.88]
2.300[58.42]
2.400[60.96]
2.500[63.50]
2.600[66.04]
B
Vertical SMT Headers
C
D
E
Plating A
Plating B
Plating C
.220[5.59]
.100[2.54]
.220[5.60]
.110[2.80]
1375583-1
1375582-1
1375549-1
.320[8.13]
.420[10.67]
.520[13.21]
.620[15.75]
.720[18.29]
.820[20.83]
.920[23.37]
1.020[25.91]
1.120[28.45]
1.220[30.99]
1.320[33.53]
1.420[36.07]
1.520[38.61]
1.620[41.15]
1.720[43.69]
1.820[46.23]
1.920[48.77]
2.020[51.31]
2.120[53.85]
2.220[56.39]
2.320[58.93]
2.420[61.47]
2.520[64.01]
.200[5.08]
.300[7.62]
.400[10.16]
.500[12.70]
.600[15.24]
.700[17.78]
.800[20.32]
.900[22.86]
1.000[25.40]
1.100[27.94]
1.200[30.48]
1.300[33.02]
1.400[35.56]
1.500[38.10]
1.600[40.64]
1.700[43.18]
1.800[45.72]
1.900[48.26]
2.000[50.80]
2.100[53.34]
2.200[55.88]
2.300[58.42]
2.400[60.96]
.320[8.14]
.420[10.68]
.520[13.22]
.620[15.76]
.720[18.30]
.820[20.84]
.920[23.38]
1.020[25.92]
1.120[28.46]
1.220[31.00]
1.320[33.54]
1.420[36.08]
1.520[38.62]
1.620[41.16]
1.720[43.70]
1.820[46.24]
1.920[48.78]
2.020[51.32]
2.120[53.86]
2.220[56.40]
2.320[58.94]
2.420[61.48]
2.520[64.02]
.160[4.07]
.210[5.34]
.260[6.61]
.310[7.88]
.360[9.15]
.410[10.42]
.460[11.69]
.510[12.96]
.560[14.23]
.610[15.50]
.660[16.77]
.710[18.04]
.760[19.31]
.810[20.58]
.860[21.85]
.910[23.12]
.960[24.39]
1.010[25.66]
1.060[26.93]
1.110[28.20]
1.160[29.47]
1.210[30.74]
1.260[32.01]
1375583-2
1375583-3
1375583-4
1375583-5
1375583-6
1375583-7
1375583-8
1375583-9
1-1375583-0
1-1375583-1
1-1375583-2
1-1375583-3
1-1375583-4
1-1375583-5
1-1375583-6
1-1375583-7
1-1375583-8
1-1375583-9
2-1375583-0
2-1375583-1
2-1375583-2
2-1375583-3
2-1375583-4
1375582-2
1375582-3
1375582-4
1375582-5
1375582-6
1375582-7
1375582-8
1375582-9
1-1375582-0
1-1375582-1
1-1375582-2
1-1375582-3
1-1375582-4
1-1375582-5
1-1375582-6
1-1375582-7
1-1375582-8
1-1375582-9
2-1375582-0
2-1375582-1
2-1375582-2
2-1375582-3
2-1375582-4
1375549-2
1375549-3
1375549-4
1375549-5
1375549-6
1375549-7
1375549-8
1375549-9
1-1375549-0
1-1375549-1
1-1375549-2
1-1375549-3
1-1375549-4
1-1375549-5
1-1375549-6
1-1375549-7
1-1375549-8
1-1375549-9
2-1375549-0
2-1375549-1
2-1375549-2
2-1375549-3
2-1375549-4
270
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Colored MTE Interconnection System-4 position only
Colored Polarized
Latching Receptacle
Mates to Colored
Vertical Header with PC
Board orientation:
Material and Finish:
Housing – Color Thermoplastic,
94V-0 rated
Contact/post – Copper alloy, plated
.000100-.000200 [0.00254-0.00508]
tin-lead over .000050 [0.00127] nickel
on entire contact/post.
Technical Documents (pages
295, 296):
Product Specification
108-25034
Application Specification
114-25026
Photo 107800
Refer to pages 247 and 265 for line
art and customer drawings for
specific dimensions.
Note: The .065+/-.003 [1.65+/-0.08]
diameter hole, used for PCB
orientation, changes in position for
headers listed below.
Strip Form
Housing
Quantities
5
5
5
5
Color
Natural/ Beige
Green
Blue
Yellow
147050-1
ø.065±.003 Typ.
[1.65±0.08]
ø.040±.003
[1.02±0.08] Typ.
Receptacle
30-26 AWG
[0.05-0.15mm2] Wire
147048-1
147048-2
147048-3
147048-4
147050-2
.025
[0.63]
Mates
with
Header
––
––
––
––
147050-1
147050-2
147050-3
147050-4
Unloaded
Receptacle
Housing
147047-1
147047-2
147047-3
147047-4
147050-3
147050-4
.025
[0.63]
.075
[1.91]
.025
[0.64]
.135
[3.43] Typ.
.100
[2.54]
Typ.
Recommended
Hole Layout
Recommended
Hole Layout
Recommended
Hole Layout
Recommended
Hole Layout
5
PC Board Orientation Feature
271
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Interchangeable Contacts, Wire Crimp (Snap-In)
Material and Finish:
Short Point Receptacles
.068
[1.73]
Copper alloy C7025, plated as follows:
Plating A—Duplex plated .000030
[0.00076] min. gold on contact area,
.000050 [0.00127] min. tin-lead in
crimp area, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating B—Duplex plated .000015
[0.00038] min. gold on contact area,
.000050 [0.00127] min. tin-lead in
crimp area, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating C—.000100 [0.00254] min.
bright tin-lead over .000050 [0.00127]
min. nickel on entire contact
C
Keying Plug
Part No. 104072-1
Ten plugs are supplied per strip.
Order quantity reflects the number
of strips required.
5
Section C - C
Related Product Data:
Technical Documents (page
Performance Characteristics—
page 238
Housings used in—
Short Point—pages 240, 241
AMPMODU MTE Unloaded
Housings—pages 245-250
Application Tooling—
pages 289, 290
295, 296):
Ins.
Dia.
Range
32-28
0.03-0.08
.025-.060
0.64-1.52
26-22
0.13-0.3
.025-.060
0.64-1.52
24-20
0.2-0.5
.025-.060
0.64-1.52
C
.012
[0.30]
Gap
Photo 4857
Extraction/Lance Reset
Tool No. 843477-1
Wire Size
Range
AWG
[mm2]
.060
[1.52]
.460
[11.68]
Product Specification
108-1472, 108-1472-1
Application Specification
114-25038
Finish
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
Contact Part No.
(Standard Pressure)
Strip Form Loose Piece
104481-4
104481-3
104481-2
104480-4
104480-3
104480-2
104479-4
104479-3
104479-2
104481-8
104481-7
104481-6
104480-9
104480-8
104480-7
104479-7
104479-6
104479-5
Heavy Duty Miniature
Applicator for
AMP-O-LECTRIC
Machine*
Applicator for
AMP-O-MATIC
Stripper/Crimper
Machine
Hand
Tool
Nos.
567296-2
466980-1
91518-1
567297-2
466981-1
91518-1
567298-2
466982-1
91551-1
*For use with Model “K” machines. Call the Technical Support Center (1-800-522-6752) for part nos. of applicators for use with the Model “G” machines (shown
on page 289), as well as other bench machines and fully automatic AMPOMATOR lead making machines.
Note: These wire crimp contacts can be intermixed with insulation displacement crimp contacts.
272
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Interchangeable Contacts, Wire Crimp (Snap-In) (Continued)
Material and Finish:
Pins
Phosphor bronze, plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold on contact area, .000030
[0.00076] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold on contact area, .000030
[0.00076] min. tin-lead in crimp area,
with entire contact underplated .000050
[0.00127] nickel
Plating C—.000100 [0.00254] min.
bright tin-lead over .000050 [0.00127]
nickel on entire contact
.025
[0.64]
.025
[0.64]
Extraction/Lance Reset
Tool No. 843477-1
.810
[20.57]
Related Product Data:
Performance Characteristics—
page 238
AMPMODU MTE Unloaded
Housings—pages 245-250
Application Tooling—
pages 289, 290
Technical Documents (page
295, 296):
Product Specification
108-25034
Application Specification
114-25026
Wire Size
Range
AWG
[mm2]
Ins. Dia.
Range
32-28
0.03-0.08
.025-.054
0.64-1.37
26-22
0.14-0.32
.036-.054
0.91-1.37
Finish
Plating A
Plating B
Plating C
Plating A
Plating B
Plating C
Contact
Part No.
(Standard Pressure)
Strip
Loose
Form
Piece
104506-6
104506-7
104506-4
104506-5
104506-2
104506-3
104505-6
104505-7
104505-4
104505-5
104505-2
104505-3
Applicator for
Heavy Duty
Miniature Applicator AMP-O-MATIC
Stripper/
for AMP-O-LECTRIC
Crimper
Machine*
Machine
Hand
Tool
Nos.
—
—
58342-2
567239-2
466983-1
91531-1
5
*For use with AMP-O-LECTRIC Model “K” machines. Call Technical Support Center (1-800-522-6752) for part nos. of applicators for use with the
AMP-O-LECTRIC Model “G” machines (shown on page 289), as well as other bench machines and fully automatic AMPOMATORlead making machines.
Note: These wire crimp contacts can be intermixed with insulation displacement crimp contacts.
273
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MT and Shielded MT Interconnection System
Product Facts
■
Full line of mass termination
tooling offers lowest installed
cost for most production
needs
■
Dual cantilever beams with
anti-overstress features
provide redundant contact
of mating post and limit
beam deflection, preventing
permanent deformation
■
Redundant insulation
displacement slots provide
for maximum reliability
■
Integral wire strain relief on
contact prevents wire motion
from being transmitted to
wire termination areas
■
Built-in contact post stop
protects terminated wire
from being disturbed by
over-insertion of mating
post, prevents wire from
entering contact area and
positively limits mating
connector depth
■
5
Insulation displacement
contacts and crimp, snap-in
contacts are interchangeable
■
Complete serviceability
with replacement contacts
■
Cover styles include low
profile (polarized, nonpolarized, latching and
ejection) and standard
profile (hermaphroditic
and ejection)
■
Connector housings may be
stacked end-to-end within one
pair of covers. All varieties
of covers in this catalog are
suitable for multiple housing
stacking applications similar
to the example illustrated in
the photograph to the right
■
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
■
Certified by Canadian
Standards
Association,
File No. LR 7189
Typical Application of End-to-End Stacking
Wire-to-Board
102398-8 D-R Assembly
102396-8 Hermaphroditic Covers
102398-8 D-R Assembly
102540-8 Polarizing Cover
102536-8 Back Cover
102398-8 D-R Assembly
102537-8 Ejection Cover
102536-8 Back Cover
102398-8 D-R Assembly
102541-8 Non-Polarizing Cover
102536-8 Back Cover
102185-2 Latch
103168-8 Hdr
102154-4 Header
102398-8 D-R Assembly
102681-5 Latching Cover
102536-8 Back Cover
103166-8 Header
103166-8 Header
102398-8 D-R Assembly
102396-8 Hermaphroditic Covers
The AMPMODU MT and
Shielded MT Interconnection
System offers labor and
cost savings through mass
termination technology,
while maintaining the timeproven reliability of the
AMPMODU product family.
The MT system is comprised
of preloaded, double-row
receptacle assemblies with
snap-on covers and a variety
of shielding hardware and
accessories. The system is
supported by a full line of
mass termination tooling to
meet virtually most
production needs.
system, features a mating
interface that is the same as
the conventional AMPMODU
crimp, snap-in contact,
featuring dual cantilever
beams, built-in overstress
protection and a completely
enclosed “box” design.
To reduce EMI/ESD
(electromagnetic
interference/
electrostatic discharge) at
the input-output interface,
add-on metal shields can be
used to convert standard
MT connectors to shielded
MT connectors.
Performance
Characteristics
Contact Current Rating—3 amperes
for single contact in free air. (Amperage
could vary due to ambient temperature,
wire size and duty cycles.)
Operating Temperature—-65°C to +105°C
Termination Resistance—
12 milliohms max.
Max. Mating Force—
High pressure - 26 oz. [7.23 N]
Standard pressure - 9 oz. [2.50 N]
Min. Unmating Force—High pressure - 5 oz. [1.39 N]
Standard pressure - 1.5 oz. [0.417 N]
Contact Retention in Housing—
5 lb. [22.24 N] per contact min.
The insulation displacement
contact, the heart of the MT
274
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MT Receptacle Assemblies, Double-Row
.100 x .100 [2.54 x 2.54] Centerline
Housings Pre-loaded with
Standard Pressure Contacts
Contact
I.D. No.
1
1
1
1
1
.125
[3.18]
1
.600
[15.24]
.270
[6.86]
A Max.
Circuit No. 1
Identifier
Material and Finish:
Housing—Black thermoplastic, flame
retardant
Contacts—Copper alloy, duplex plated
.000030 [0.00076] gold on contact area,
.000050 [0.00127] min. tin-lead in crimp
area, with entire contact underplated
.000050 [0.00127] nickel
.070
[1.78]
.050
[1.27]
Technical Documents (pages
295, 296):
Product Specification
108-25015, 108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
MT Receptacle
Assembly
Right-Angle
Header
.300
[7.62]
.240
[6.10]
Related Product Data:
Mateable Connectors—pages 133,
139, 143, 147, 283
Cable Insulation Wall Thickness—
.015 [0.39] max.
Cable Insulation Diameter—
.050 [1.27] max.
Mating Post Length—
.222-.273 [5.64-6.94] max.
Performance Characteristics—
page 274
Replacement Contacts—page 284
Connector Covers—
pages 277, 278
Application Tooling—
pages 290-293
B
.100
[2.54]
.100
Typ.
[2.54]
PC
Board
Part Nos. (Stamped)
Wire Size Range
30-26 AWG
26-22 AWG
2
[0.05-0.15 mm ]
[0.12-0.3 mm2]
6
.300 [7.62]
.200 [5.08]
102393-1
102398-1
8
.400 [10.16] .300 [7.62]
102393-2
102398-2
10
.500 [12.70] .400 [10.16]
102393-3
102398-3
12
.600 [15.24] .500 [12.70]
102393-4
102398-4
14
.700 [17.78] .600 [15.24]
102393-5
102398-5
16
.800 [20.32] .700 [17.78]
102393-6
102398-6
18
.900 [22.86] .800 [20.32]
102393-7
102398-7
20
1.000 [25.40] .900 [22.86]
102393-8
102398-8
22
1.100 [27.94] 1.000 [25.40]
102393-9
102398-9
24
1.200 [30.48] 1.100 [27.94]
1-102393-0
1-102398-0
26
1.300 [33.02] 1.200 [30.48]
1-102393-1
1-102398-1
28
1.400 [35.56] 1.300 [33.02]
1-102393-2
1-102398-2
30
1.500 [38.10] 1.400 [35.56]
1-102393-3
1-102398-3
32
1.600 [40.64] 1.500 [38.10]
1-102393-4
1-102398-4
34
1.700 [43.18] 1.600 [40.64]
1-102393-5
1-102398-5
40
2.000 [50.80] 1.900 [48.26]
1-102393-8
1-102398-8
50
2.500 [63.50] 2.400 [60.96]
2-102393-3
2-102398-3
60
3.000 [76.20] 2.900 [73.66]
2-102393-8
2-102398-8
64
3.200 [81.28] 3.100 [78.74]
3-102393-0
3-102398-0
Note: Contact Extraction/Lance Reset Tool No. 843477-3, see page 284.
No. of
Pos.
Dimensions
A
B
.270
[6.86]
22-20 AWG
[0.3-0.6 mm2]
102448-1
102448-2
102448-3
102448-4
102448-5
102448-6
102448-7
102448-8
102448-9
1-102448-0
1-102448-1
1-102448-2
1-102448-3
1-102448-4
1-102448-5
1-102448-8
2-102448-3
2-102448-8
3-102448-0
Unloaded
Housings
102394-1
102394-2
102394-3
102394-4
102394-5
102394-6
102394-7
102394-8
102394-9
1-102394-0
1-102394-1
1-102394-2
1-102394-3
1-102394-4
1-102394-5
1-102394-8
2-102394-3
2-102394-8
3-102394-0
Keying Plugs
5
Part No. 86286-1
(Plugs into receptacle contact)
Material—Natural color nylon
Part No. 87077-2
(Plugs directly into housing)
275
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
MT Receptacle Assemblies, Double-Row
.100 x .100 [2.54 x 2.54] Centerline
Housings Pre-loaded with
High Pressure Contacts
Contact
I.D. No.
4
4
4
4
4
4
4
4
4
4
.125
[3.18]
.600
[15.24]
.270
[6.86]
Material and Finish:
A Max.
Housing—Black thermoplastic, flame
retardant
Contacts—Copper alloy, duplex plated
.000030 [0.00076] gold on contact area,
.000050 [0.00127] min. tin-lead in crimp
area, with entire contact underplated
.000050 [0.00127] nickel
Circuit No. 1
Identifier
.050
[1.27]
B
Related Product Data:
Mateable Connectors—pages 133,
139, 143, 147, 283
Cable Insulation Wall Thickness—
.015 [0.39] max.
Cable Insulation Diameter—
.050 [1.27] max.
Mating Post Length—
.200-.273 [5.64-6.94] max.
Performance Characteristics—
page 274
Replacement Contacts—page 284
Connector Covers—
pages 277, 278
Application Tooling—
pages 290-293
Technical Documents (pages
295, 296):
Product Specification
108-25015, 108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
MT Receptacle
Assembly
Right-Angle
Header
.240
[6.10]
.300
[7.62]
.100
Typ.
[2.54]
.100
[2.54]
PC
Board
.270
[6.86]
Part Nos. (Stamped*)
Wire Size Range
A
B
30-26 AWG
26-22 AWG
22-20 AWG
[0.05-0.15 mm2]
[0.12-0.3 mm2]
[0.3-0.6 mm2]
6
.300 [7.62]
.200 [5.08]
102693-1
102694-1
102695-1
8
.400 [10.16]
.300 [7.62]
102693-2
102694-2
102695-2
10
.500 [12.70]
.400 [10.16]
102693-3
102694-3
102695-3
12
.600 [15.24]
.500 [12.70]
102693-4
102694-4
102695-4
14
.700 [17.78]
.600 [15.24]
102693-5
102694-5
102695-5
16
.800 [20.32]
.700 [17.78]
102693-6
102694-6
102695-6
18
.900 [22.86]
.800 [20.32]
102693-7
102694-7
102695-7
20
1.000 [25.40]
.900 [22.86]
102693-8
102694-8
102695-8
*Cavity identification — first cavity (one side); Tyco Electronics Part No. and date code stamped on housing where size permits.
Note: Contact Extraction/Lance Reset Tool No. 843477-3, see page 284.
No. of
Pos.
Dimensions
Keying Plugs
5
Part No. 86286-1
(Plugs into receptacle contact)
Material—Natural color nylon
Part No. 87077-2
(Plugs directly into housing)
276
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Low Profile Covers for Double-Row MT Receptacle Assemblies
Material:
Front Covers
Black thermoplastic, flame retardant
A - Polarizing Cover
(Mates with AMPMODU 4-sided shrouded
headers. Refer to pages 133, 139, 143, 147.)
Related Product Data:
For use on Double-Row MT Receptacle
Assemblies—pages 275, 276
B - Latching Cover
(Mates with AMPMODU 4-sided shrouded
headers with extraction slot. Refer to
pages 133, 139, 143, 147.)
.750
[19.05]
.750
[19.05]
L
L
Technical Documents (pages
295, 296):
Product Specification
108-25015, 108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
Note: See page 278 for Low Profile
Cover Part Nos.
C - Ejection Cover
(Mates with AMP-LATCH universal ejection
style pin headers equipped with latching
ears, Part No. 102185-2 (with push tabs)
or Part No. 102312-2 (without push tabs),
see AMP Catalog 82012.
D - Non-Polarizing Cover
(Designed for use with shielded connectors,
pages 280 & 281; or for non-polarizing
applications.)
.750
[19.05]
Assembled*
.750
[19.05]
.480
[12.19]
.095
Typ.
[2.41]
.150
[3.81]
.468
[11.89]
*Dimension applies to cover when
installed on connector housing.
Back Covers
E - For Shielding and
Non-Shielding Applications
(For use with any low profile cover.)
L
F - For Shielding Applications
(For use with Non-Polarizing Cover only.)
L
5
277
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Standard Profile Covers for Double-Row MT Receptacle Assemblies
Material:
Black thermoplastic, flame retardant
G - Hermaphroditic Cover
(Two hermaphroditic covers can be used
or one hermaphroditic cover can be used
with an H Ejection Cover.)
Related Product Data:
1.120 Assembled*
[28.45]
For use on Double-Row MT Receptacle
Assemblies—pages 275, 276
Technical Documents (pages
H - Ejection Cover
(Mates with AMP-LATCH universal ejection style
pin headers equipped with latching ears, Part No.
102185-2 (with push tabs) or Part No. 102312-2
(without push tabs), see Tyco Electronics Catalog
82012.
.850
[21.59]
Top View
1.120
[28.45]
295, 296):
Product Specification
108-25015, 108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
.095
[2.41]
Typ.
Bottom View
.150
[3.81]
*Dimension applies to cover when
installed on connector housing.
.468
[11.89]
L
Low Profile Covers
No. of
Pos.
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
40
50
60
64
Front Covers
Dimension
L
.300 [7.62]
.400 [10.16]
.500 [12.70]
.600 [15.24]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
2.000 [50.80]
2.500 [63.50]
3.000 [76.20]
3.200 [81.28]
A
Polarizing
B
Latching
102540-1
102540-2
102540-3
102540-4
102540-5
102540-6
102540-7
102540-8
102540-9
1-102540-0
1-102540-1
1-102540-2
1-102540-3
—
—
—
—
—
—
—
—
—
102681-1
102681-2
102681-3
102681-4
102681-5
102681-6
102681-7
102681-8
102681-9
1-102681-0
1-102681-1
1-102681-2
1-102681-5
2-102681-0
—
—
Standard Profile Covers
Back Covers
C
Ejection
D
Non-Polarizing
E
Shielding and
Non-Shielding
Applications
102537-1
102537-2
102537-3
102537-4
102537-5
102537-6
102537-7
102537-8
102537-9
1-102537-0
1-102537-1
1-102537-2
1-102537-3
1-102537-4
1-102537-5
1-102537-8
2-102537-3
2-102537-8
3-102537-0
102541-1
102541-2
102541-3
102541-4
102541-5
102541-6
102541-7
102541-8
102541-9
1-102541-0
1-102541-1
1-102541-2
1-102541-3
1-102541-4
1-102541-5
1-102541-8
2-102541-3
2-102541-8
3-102541-0
102536-1
102536-2
102536-3
102536-4
102536-5
102536-6
102536-7
102536-8
102536-9
1-102536-0
1-102536-1
1-102536-2
1-102536-3
1-102536-4
1-102536-5
1-102536-8
2-102536-3
2-102536-8
3-102536-0
F
Shielding
Applications
—
—
—
102823-5
102823-6
102823-7
102823-1
102823-4
102823-8
102823-9
1-102823-0
1-102823-1
1-102823-2
1-102823-3
1-102823-4
102823-2
102823-3
—
—
G
Hermaphroditic
102396-1
102396-2
102396-3
102396-4
102396-5
102396-6
102396-7
102396-8
102396-9
1-102396-0
1-102396-1
1-102396-2
1-102396-3
1-102396-4
1-102396-5
1-102396-8
2-102396-3
2-102396-8
3-102396-0
H
Ejection
—
—
—
—
—
—
—
103268-6
—
103268-7
103268-8
—
103268-9
—
1-103268-0
—
1-103268-3
—
—
5
278
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Shielding Hardware and Accessories for MT Interconnection System
Product Facts
■
Add-on shielding accessories
for existing AMPMODU
Standard MT and PC board
mounted headers
■
Compact design
■
Tin plated copper alloy
material
■
Redundant cantilever beams
provide for good peripheral
contact, eliminating the
need for a separate RF
gasket
■
Polarized mating
■
360° cable braid termination
with cable jacket support
■
Cable shielding hardware
permits molded cable
terminations after assembly
■
Must be used with braided
shielded cables
■
Solder tabs on right-angle
header shields are selfretaining in a PC board
Photo 110928
Shielded MT Receptacles
Photo 98187
Shielded Right-Angle Headers
The shielded AMPMODU MT
system features add-on
metal shielding kits for
double-row standard MT
receptacle assemblies and
double-row right-angle
headers.
Cable shielding hardware
consists of a ferrule and two
stamped and formed shell
halves. The inner shell half
has a series of integral
cantilever beams to provide
good peripheral contact with
the mating outer shell half.
This feature also eliminates
the need for a separate RF
gasket. Detents in the
cantilever beam provide a
positive lock when the two
halves are mated. During
assembly the inner and
outer shell halves are
snapped together over a
terminated standard MT
connector.
Shields for right-angle
headers have integral
cantilever beams which
provide good contact with
the mating shielded MT
receptacle assembly,
without the use of a separate
RF gasket.
5
279
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Shielding Hardware and Accessories for
Double-Row MT Receptacle Assemblies
Two-Piece Shields—
Straight Exit
Outer Shell Half
Material and Finish:
Shell Halves—Copper alloy, .020
[0.51] thick; pretinned .000030
[0.00076] min.
A
C
Related Product Data:
B
Double-Row MT Receptacle
Assemblies—pages 275, 276
Non-Polarizing Covers (Part No.
Series 102541 with back cover
102536 or 102823)—
pages 277, 278
Shield Ferrules—page 282
.326
[8.28]
Ferrule Purchased
separately
(See page 282)
Technical Documents (pages
295, 296):
Product Specification
108-25015, 108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
Flare braid over
assembled shells for
crimping under ferrule
Standard MT
Receptacle Assembly
Purchased separately
(Refer to pages 275 & 276)
Inner Shell Half
No. of
Pos.
6
10
16
26
40
50
5
A
Dimensions
B
.410 [10.41]
.610 [15.49]
.910 [23.11]
1.410 [35.81]
2.110 [53.59]
2.610 [66.29]
.817 [20.75]
.817 [20.75]
.950 [24.13]
.950 [24.13]
1.325 [33.66]
.950 [24.13]
C
1.268 [32.21]
1.667 [42.34]
1.925 [48.90]
1.925 [48.90]
2.468 [62.69]
2.468 [62.69]
Part Nos.
Outer
Shell
102988-2
103137-2
103153-2
103341-2
104272-1
103158-2
Inner
Shell
102987-6
103136-2
103152-2
103340-2
104271-1
103157-2
Note: Match shield size to number of connector positions.
280
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Shielding Hardware and Accessories for
Double-Row MT Receptacle Assemblies (Continued)
Two-Piece Shields—
Right-Angle Exit
.125
Dia.
[3.18]
(See Note 2)
Material and Finish:
C
Outer Shell Half
Shell Halves—Copper alloy, .020
[0.51] thick; pretinned .000030
[0.00076] min.
A
Related Product Data:
Double-Row MT Receptacle
Assemblies—pages 275, 276
Non-Polarizing Covers (Part No.
Series 102541 with back cover
102536 or 102823)—
pages 277, 278
Shield Ferrules—page 282
B
Ferrule Purchased
separately
(See page 282)
.326
[8.28]
Flare braid over
assembled shells for
crimping under ferrule
Technical Documents (pages
295, 296):
Product Specification 108-25015,
108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
Standard MT
Receptacle Assembly
Purchased separately
(Refer to pages 275 & 276)
Inner Shell Half
No. of
Pos.
Dimensions
Part Nos.
A
B
C
Outer Shell
Inner Shell
18
1.010 [25.65]
1.120 [28.45]
1.413 [35.89]
102784-2
102783-2
26
1.410 [35.81]
1.166 [29.62]
1.975 [50.17]
103139-2
103138-2
40
2.110 [53.59]
1.135 [28.83]
2.633 [66.88]
102786-2
102785-2
50
2.610 [66.29]
.983 [24.97]
3.133 [79.58]
102788-2
102787-2
60
3.110 [78.99]
1.118 [28.40]
3.606 [91.59]
103141-2
103140-2
Notes: 1. Match shield size to number of connector positions.
Notes: 2. Hole is provided in 26 through 60-position cable shields for application of optional cable tie pull ring after
Notes: 2. assembly.
5
281
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Shielding Hardware and Accessories for
Double-Row MT Receptacle Assemblies (Continued)
Ferrules for Shielding Kits
Material and Finish:
Soft copper, tin plated
Related Product Data:
Used with Shielding Kits—
pages 280, 281
Technical Documents (pages
295, 296):
Product Specification 108-25015,
108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
Application Tooling
Photo 110600
AMP-O-LECTRIC Model
“G” Terminating Machine
No. of
Positions
5
Straight-Exit Shields
Outer
Inner
Right-Angle Exit Shields
Outer
Inner
6
102988-2
102987-6
—
—
10
103137-2
103136-2
—
—
16
103153-2
103152-2
—
—
18
—
—
102784-2
102783-2
26
103341-2
103340-2
103139-2
103138-2
40
104272-1
104271-1
102786-2
102785-2
50
103158-2
103157-2
102788-2
102787-2
60
—
—
103141-2
103140-2
AMP Hand Tool 91410-1
(DIe Set required, see table below)
Cable Dia.
Range
0.170-0.195 [4.32-4.95]
0.200-0.250 [5.08-6.35]
0.190-0.240 [4.83-6.10]
0.250-0.300 [6.35-7.62]
0.310-0.360 [7.87-9.14]
0.370-0.420 [9.40-10.67]
0.190-0.240 [4.83-6.10]
0.250-0.300 [6.35-7.62]
0.310-0.360 [7.87-9.14]
0.370-0.420 [9.40-10.67]
0.190-0.240 [4.83-6.10]
0.250-0.300 [6.35-7.62]
0.310-0.360 [7.87-9.14]
0.370-0.420 [9.40-10.67]
0.320-0.370 [8.13-9.40]
0.380-0.420 [9.65-10.67]
0.430-0.460 [10.92-11.68]
0.320-0.370 [8.13-9.40]
0.380-0.420 [9.65-10.67]
0.430-0.460 [10.92-11.68]
0.380-0.420 [9.65-10.67]
0.430-0.460 [10.92-11.68]
0.470-0.520 [11.94-13.21]
0.470-0.520 [11.94-13.21]
0.500-0.545 [12.70-13.84]
0.550-0.600 [13.97-15.24]
Ferrule
Part Number
1-102903-83
102985-3
1-102903-5
102903-9
102903-3
102789-3
1-102903-5
102903-9
102903-3
102789-3
1-102903-5
102903-9
102903-3
102789-3
2-102903-4
2-102903-1
102789-6
2-102903-4
2-102903-1
102789-6
3-102903-0
2-102903-7
102789-9
3-102903-6
3-102903-3
1-102789-2
Applicator Die*
Assembly Part No.
812665-1
812665-2
812665-6
812665-5
812665-4
812665-3
812665-6
812665-5
812665-4
812665-3
812665-6
812665-5
812665-4
812665-3
812665-9
812665-8
812665-7
812665-9
812665-8
812665-7
1-812665-5
1-812665-4
1-812665-3
1-812665-8
1-812665-7
1-812665-6
Hand Tool Die Sets
Insulation
Braid
1-527116-9
527116-4
1-527116-8
527116-4
1-527116-7
527116-3
1-527116-6
527116-3
1-527116-5
527116-3
1-527116-4
527116-3
1-527116-7
527116-3
1-527116-6
527116-3
1-527116-5
527116-3
1-527116-4
527116-3
1-527116-7
527116-3
1-527116-6
527116-3
1-527116-5
527116-3
1-527116-4
527116-3
1-527116-3
527116-2
1-527116-2
527116-2
1-527116-1
527116-2
1-527116-3
527116-2
1-527116-2
527116-2
1-527116-1
527116-2
1-527116-2
527116-1
1-527116-1
527116-1
1-527116-0
527116-1
—
—
—
—
—
—
*For use with Model “K” machines. Call the Tyco Electronics Technical Support Center (1-800-522-6752) for part nos. of applicators for use with the
AMP-O-LECTRIC Model “G” machines (also shown on page 289), as well as other bench machines and fully automatic AMPOMATORlead making
machines.
Notes: 1. Ferrules are used with shielding kits shown on pages 280 & 281, and are purchased separately.
2. Individual anvils and crimpers also may be purchased separately.
3. Ferrule Part Number 1-102903-8 also requires Spacer Part Number 527116-9.
282
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Shielded MT Headers for use with Shielded MT Receptacle Assemblies
AMPMODU Right-Angle
Headers PC Board Mounted
.755
[19.18]
C
Material and Finish:
Housing—Black thermoplastic,
flame retardant
Posts—Copper alloy, plated .000030
[0.00076] gold over .000050 [0.00127]
nickel on entire post
Shield—Copper alloy, .020 [0.51]
thick; pretinned .000030 [0.00076] min.
.460
[11.68]
Shield
Right-Angle
Header
B
.550
[13.97]
.125
[3.18]
Related Product Data:
Mating Connectors—Double-Row
MT Receptacle Assemblies with
Shielding Hardware—pages 275-282
.030
[0.76]
.434
[11.02]
.025
[0.64] Sq. Posts
.290
[7.37]
A
Technical Documents (pages
295, 296):
Product Specification 108-25015,
108-25018, 108-25030
Application Specification
114-25032.
Instruction Sheet
408-6532
.135
[3.43]
.318
[8.08]
.145±.003
[3.68±0.08]
2 Plc.
.145±.003
[3.68±0.08]
2 Plc.
A
A
.050±.003
[1.27±0.08]
.725
[18.45]
.550±.003
[13.97±0.08]
.100±.003
[2.54±0.08]
±.003
D [±0.08]
.040±.003
Dia.
[1.02±0.08]
(All holes)
±.003
D [±0.08]
±.003
2D [±0.08]
Recommended PC Board Hole Layout
for 6, 8 and 10 Positions
.100±.003
[2.54±0.08]
2D ±.003
[±0.08]
Recommended PC Board Hole Layout
for 16 thru 50 Positions
D - Contact centerline is .100 [2.54]; ±.003 [0.08] tolerances
not to accumulate within one connector pattern.
No. of
Pos.
6
8
10
16
18
20
26
50
A
.200 [5.08]
.300 [7.62]
.400 [10.16]
.700 [17.78]
.800 [20.32]
.900 [22.86]
1.200 [30.48]
2.400 [60.96]
Dimensions
B
.430 [10.92]
.530 [13.46]
.630 [16.00]
.930 [23.62]
1.030 [26.16]
1.130 [28.70]
1.430 [36.32]
2.630 [66.80]
C
.510 [12.95]
.610 [15.49]
.710 [18.03]
1.010 [25.65]
1.110 [28.19]
1.210 [30.73]
1.510 [38.35]
2.710 [68.83]
Header
Part Nos.
102792-6
102792-8
102792-1
102792-7
102792-2
102792-5
102792-9
102792-4
Shield
Part Nos.
102991-1
102991-2
102791-2
102791-3
102791-4
1-102791-0
102791-1
102791-8
5
283
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
Replacement MT Receptacle Contacts
Insulation Displacement
Contacts
Contact
Identification
Material and Finish:
Copper alloy, duplex plated .000030
[0.00076] gold on contact area,
.000100-.000200 [0.00254-0.00508]
tin-lead in crimp area, with entire contact
underplated .000050 [0.00127] nickel
.050
Max.
[1.27]
Insulation
Diameter
Related Product Data:
Performance Characteristics—
page 274
Application Tooling—pages 290-293
Technical Documents (pages
295, 296):
Wire Size Range
AWG
[mm2]
30-26
26-22
22-20
0.05-0.15
0.12-0.3
0.3-0.6
Standard Pressure
Receptacle
Contact Ident.
Part No.
1
102395-3
2
102399-3
3
102449-3
High Pressure
Receptacle
Contact Ident.
Part No.
4
102641-3
5
102642-3
—
—
Note: Termination tooling for MT receptacle insulation displacement contacts is shown on pages 290 thru 293.
Product Specification 108-25015,
108-25018, 108-25030
Application Specification
114-25032
Instruction Sheet
408-6532
MT receptacle contacts
incorporate the following
features.
Cantilever
Beams
Antioverstress
Wide
Misalignment
Tolerance
The MT receptacle contact
cross-section is primarily
rectangular, with rounded
corners. Two integral
contilever beams contact
the mating square male
posts. Deflection of these
spring members is limited
by anti-overstress and
excessive permanent
deformation is prevented.
This feature allows a wide
range for tolerance of
misalignment of mating
contacts.
The configuration of the
receptacle completely
encloses the spring
members helping to prevent
damage during handling
and assembly, and makes
the system compatible with
automatic application
techniques.
Extraction/Lance Reset Tool
No. 843477-3
5
284
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
AMP Mini-Tandem Spring Receptacle Housings and Contacts
Product Facts
■
Individual contacts mate
with .025 [0.64] sq. posts,
.125 [3.18] long
■
Crimp snap-in contacts
accept 32-22 AWG
[0.03-0.32 mm2] wire
■
Retention latch provides for
positive installation
■
No insertion tool required
■
High durability design
provides long life
■
Available with .000015
[0.00038] or .000030
[0.00076] thick gold inlay
in contact areas, or bright
tin plated
■
Closed-entry housings
■
Mini-contact box size:
.060 [1.52] sq.
■
Mini-Tandem Spring
Housings can be stacked
on .100 [2.54] centers in
either direction
■
■
Mini-Tandem
Spring Housings are
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
Certified by Canadian
Standards
Association,
File No. LR 7189
Photo 196196
AMP Mini-Tandem Spring
Receptacle Contacts are
designed to mate with .025
[0.64] posts. When used
individually, they will mate
with posts as short as .125
[3.18] and when used in a
housing, they will mate with
.140 [3.55] long posts.
These versatile contacts
may be used for
interconnecting posted
pc panels, I/O wiring and
cross-connecting pin
arrays.
AMP Mini-Tandem Spring
Receptacle Contacts are
used in single- or doublerow housings with .100
[2.54] centerline spacing.
Single-row housings can be
converted into double-row
connectors on .100 x .200
[2.54 x 5.08] centers with
the use of stacking clips.
Specifications
Contact Current Rating—3 amperes
Termination Resistance—
12 milliohms (max.)—gold plated
contacts
18 milliohms (max.)—tin plated
contacts
Durability— Ref. AMP Product
Specification 108-25031
Mini-Tandem Spring
Housings can be stacked
side-by-side or end-to-end
on .100 [2.54] centers.
The receptacle contact's
box configuration provides
for long contact life with
controlled contact mating
forces which minimize wear.
An external retention spring
facilitates quick assembly
and provides firm seating in
a contact housing.
5
285
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
AMP Mini-Tandem Spring Housings, Single-Row
.100 [2.54] Centerline
.550
[13.97]
.030
[0.76]
Material—Black glass-filled
.036
[0.91]
polyester, 94V-0 rated
.066
[1.68]
Technical Documents (page
295):
.050
[1.27]
Product Specification 108-25031
Application Specification
114-25021
.100
[2.54]
.100
Max.
[2.54]
A Max.
B Spaces
@ .100 [2.54] = C
.050
[1.27]
Minimum mating post length is .140 [3.55].
Dimensions
A
B
C
2
.200 [5.08]
1
.100 [2.54]
3
.300 [7.62]
2
.200 [5.08]
4
.400 [10.16]
3
.300 [7.62]
5
.500 [12.70]
4
.400 [10.16]
7
.700 [17.78]
6
.600 [15.24]
8
.800 [20.32]
7
.700 [17.78]
10
1.000 [25.40]
9
.900 [22.86]
12
1.200 [30.48]
11
1.100 [27.94]
16
1.600 [40.64]
15
1.500 [38.10]
18
1.800 [45.72]
17
1.700 [43.18]
20
2.000 [50.80]
19
1.900 [48.26]
22
2.200 [55.88]
21
2.100 [53.34]
Note: AMP Mini-Tandem Spring contacts for use in these housings are shown on page 288.
No. of
Pos.
Material—Natural color nylon,
94V-2 rated
Housing
Part No.
530554-1
530554-2
530554-3
530554-4
530554-6
530554-7
530554-9
1-530554-1
1-530554-5
1-530554-7
1-530554-9
2-530554-1
5
Keying Plug
Part No. 531226-1
(Plugs directly into housing)
286
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
AMP Mini-Tandem Spring Housings, Double-Row
.100 [2.54] Centerline
.550
[13.97]
.030
[0.76]
Photo 199199
.036
[0.91]
Material—Black glass-filled
.066
[1.68]
polyester, 94V-0 rated*
Technical Documents (page 294):
A Max.
Product Specification 108-25031
Application Specification
114-25021
.200
[5.08]
.100
[2.54]
B Spaces
@ .100 [2.54] = C
.100
Max.
[2.54]
.050
[1.27]
Minimum mating post length is .140 [3.55].
Material—Natural color nylon,
94V-2 rated
Dimensions
A
B
C
4
.200 [5.08]
1
.100 [2.54]
6
.300 [7.62]
2
.200 [5.08]
8
.400 [10.16]
3
.300 [7.62]
10
.500 [12.70]
4
.400 [10.16]
12
.600 [15.24]
5
.500 [12.70]
16
.800 [20.32]
7
.700 [17.78]
20
1.000 [25.40]
9
.900 [22.86]
Note: AMP Mini-Tandem Spring contacts for use in these housings are shown on page 288.
No. of
Pos.
Keying Plug
Part No. 531226-1
(Plugs directly into housing)
Housing
Part No.
530902-5
530902-1
530902-6
530902-2
2-530902-0
3-530902-0
530902-8
5
*Consult Tyco Electronics for
specific UL recognition.
287
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
AMPMODU Interconnection System
AMP Mini-Tandem Spring Contacts
.060
[1.52]
Receptacle Contacts
Material and Finish:
Phosphor bronze, plated as follows:
Plating A—Duplex plated .000030
[0.00076] gold inlay on contact area, tin in
crimp area, with entire contact underplated
.000050 [0.00127] nickel
Plating B—Duplex plated .000015
[0.00038] gold inlay on contact area, tin in
crimp area, with entire contact underplated
.000050 [0.00127] nickel
Plating C—.000100 [0.00254] min. bright
tin over .000030 [0.00076] nickel on entire
contact
.060
[1.52]
.085
Min.
[2.15]
Contact
Area with
Gold Inlay
Technical Documents (page 294):
Product Specification 108-25031
Application Specification
114-25021
Low Pressure Contacts
Wire Size Range
AWG
26-22
mm2
0.14-0.32
Miniature
Applicator for
Applicator for AMP-O-MATIC
Loose Piece AMP-O-LECTRIC Stipper/Crimper
Machine*
Machine
Contact Part No.
Ins. Dia.
Range
Finish
0.36-0.54
[0.64-1.37]
Plating A
Plating B
Strip Form
531216-3
531216-1
531216-4
531216-2
466819-2
466943-1
Standard Pressure Contacts
Wire Size Range
Ins. Dia.
Range
AWG
mm2
32-28
0.03-0.08
.025-.054
[0.64-1.37]
26-22
0.14-0.32
.036-.054
[0.91-1.37]
Contact Part No.
Finish
Plating B
Plating C
Plating D
Plating B
Plating C
Plating D
Strip Form
Loose Piece
530901-2
530901-6
530901-4
530553-4
530553-6
530553-2
530901-3
530901-7
530901-5
530553-5
530553-7
—
Miniature
Applicator for
Applicator for
AMP-O-MATIC
AMP-O-LECTRIC Stipper/Crimper
Machine*
Machine
466723-1
466952-1
466819-2
466943-1
High Pressure Contacts
Wire Size Range
AWG
mm2
Ins. Dia.
Range
32-28
26-22
0.03-0.08
0.14-0.32
.025-.054 [0.64-1.37]
.036-.054 [0.91-1.37]
Contact Part Number
Finish
Strip Form
Loose Piece
Plating B
Plating B
531225-6
531224-6
—
531224-7
Miniature
Applicator for
AMP-O-LECTRIC
Machine*
466723-1
466819-2
Applicator for
AMP-O-MATIC
Stripper/Crimper
Machine
466952-1
466943-1
*For use with AMP-O-LECTRIC Model “K” machines. Call the Tooling/Technical Assistance Center (1-800-522-6752) for part
nos. of applicators for use with the AMP-O-LECTRIC Model “G” machines (shown on page 289), as well as other bench
machines and fully automatic AMPOMATOR lead making machines.
5
Notes: 1. Mini-Tandem Spring Receptacle Contacts are for use only in the housings shown on pages 286 & 287. They
cannot be used in AMPMODU Mod IV Housings.
2. Use Hand Tool No. 91540-1 for crimping loose-piece receptacles to all wire sizes listed above.
3. Application tooling is described on pages 289 & 293.
288
Catalog 1307819
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
工商网监
湘ICP备2023018690号
