2-1393222-9

General Purpose Low Power PCB Relays Catalo Potter & Brumfield Issued 3-03 (P Sensitive, Low Profile, Hi-Current Low profile, PCB Relay T75Designed Series Relay to Meet International Standards n 1 pole 8A, 1 form C (CO) or 1 form A (NO) contact coil-contact n Reinforced insulation (protection classII) n Ambient temperature up to 85°C at 8A n Plastic materials according to IEC60335-1 (domestic appliances) n 4kV/8mm Typical applications HVAC,security and industrial control, domestic appliances. Z Features Approvals VDE Cert. No. 3919, UL E214025 Technical data of approved types on request. Contact Data Contact arrangement 1 form C (CO) or 1 form A (NO) Rated voltage 250VAC Max. switching voltage 400VAC Rated current 8A Limiting making current, max 4s, df 10% 15A Breaking capacity max. 2000VA Contact material AgCdO Min. recommended contact load 100mA at 12VDC Minimum switching voltage 5VDC Initial contact resistance 100mΩ at 100mA, 12VDC Frequency of operation, with/without load 6/1200min-1 Operate/release time max. 10/5ms Bounce time max., form A/form B 3/10ms Coilsensitivity Data • High – nominal coil power requirement is as low as 212mW. Coil voltage range 3 to 60VDC • Low profile, .591 in. (15mm) tall case uses only .465 in2 (3cm2) of area on the Operative range, IEC permitting 61810 2 printed circuit board, high density circuit design. Coil insulation system according UL rated 10 amps classA • Power switching capability – contacts in 1 Form A (SPST-NO) or 1 Coil versions, DC coil Form C (SPDT) arrangements. Coil Rated Operate Release Coil Rated coil • Designed to meet UL, CSA, VDE, SEMKO and SEV requirements. code voltage voltage voltage power • Designed to meet VDE 8mm spacing, 4kV dielectric,resistance coil to contacts. 1) to meet VDC VDC VDC • Designed 3 mm creepage between contacts.Ω±10% mW 03 3 2.1 0.3 40 225 • Conforms to: VDE 0110 – Insulation Group C (250V) 05 5 3.4 0.5 118 212 VDE 435 Part 201 – High current applications 06 6 4.1 0.6 165 218 0804 – 6.1 Telecommunications equipment 09 VDE 9 0.9 364 223 VDE 0631 – 8.2 Temperature 1.2 652 221 controllers and limiters 12 12 VDE 0700 –16.3 Household appliances 24 24 2.4 2270 254 VDE 0805/5.90 – Office machines 48 48 32.6 4.8 8790 262 • Wash 60 tight (washable). 60 40.8 6.0 152651) 236 • Well for a±15%. broad range of applications e.g. HVAC, appliances, 1) Coilsuited resistance All figures and are given for coil control. without pre-energization, at ambient temperature +23°C. security industrial Other coil voltages on request. Insulation Data Electrical endurance Type Contact T75 T75 A (NO) T75 B (NC) T75 T75 Load 8Arms, 240VAC, resistive 14Arms, 120VAC, resistive 5Arms, 120VAC, resistive 7.2 FLA / 45 LRA, 120 VAC 5 FLA / 30 LRA, 240 VAC Cycles 100x103 50x103 50x103 30x103 10x103 Contact ratings Type Contact T75 A (NO) T75 C (CO) T75 C (CO) T75 C (CO) T75 C (CO) Load TV4, Tungsten, 120VAC, 40°C 10A, 240VAC, general purpose, 40°C 8A, 24VDC, general purpose, 40°C 1/3HP, 120VAC, 40°C 1/2HP, 240VAC, 40°C Cycles 25x103 6x103 100x103 30x103 30x103 Mechanical endurance, DC coil 10x106 operations Contact Ratings @ 25° C with relay properly vented. Remove vent nib after soldering and cleaning. Arrangements: 1 Form A (SPST-NO) and 1 Form C (SPDT). Material: Silver-cadmium oxide. Expected Mechanical Life: 10 million operations. Expected Electrical Life: 100,000 operations at 8 amps, 240VAC. 50,000 operations at 14 amps NO / 5 amps NC, 120VAC Res. 30,000 operations at 7.2 FLA, 45 LRA, 120VAC. 10,000 operations at 5 FLA, 30 LRA, 240VAC. 30,000 operations at B300 pilot duty (360VA, 240VAC; 470VA, 120VAC). Contact Ratings (See Figure 1): Maximum Switched Voltage: 380VAC. Maximum Switched Current: 14/5 (N.O./N.C.) amps, AC resistive; 8 amps DC (see Fig. 1) Maximum Switched Power: 200W, DC; 2,000VA, AC. Minimum Required Contact Load: 12V, 100mA. Initial dielectric strength VDE Contact Ratings: 8 amps, 250VAC. between open contacts 1000Vrms UL Contact 10 coil amps, 240VAC; 8 amps 24VDC; betweenRatings: contact and 4000Vrms 1/3 HP, 120VAC; 1/2 HP, 240VAC. Clearance/creepage between contact and coil Material group of insulation parts ≥8/8mm IIIa Figure 1 - DC Switching Load Limit Curve 300 01-2015, Rev. 0115 www.te.com © 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Switching Voltage (VDC) 200 100 50 Catalog 40 and product data is subject to the terms of the disclaimer and all chapters of 30 the ‘Definitions’ section, available at 25 W http://relays.te.com/definitions 20 10 Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. 50 W 10 0 W 20 0W 1 General Purpose Low Power PCB Relays Potter & Brumfield Low profile, PCB Relay T75 Series (Continued) Other Data Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at www.te.com/customersupport/rohssupportcenter Ambient temperature - 40 to +85°C Category of environmental protection IEC 61810 RTII - flux proof RTIII - wash tight Vibration resistance (functional) form A (NO) / form B (NC) 10/4g Vibration resistance (destructive) form A (NO) / form B (NC) 20/5g Shock resistance (destructive) 100g Terminal type PCB-THT Weight 11g Resistance to soldering heat THT IEC 60068-2-20 RTIII: 260°C/5s Packaging/unit tube/20 pcs., box/1000 pcs. PCB layout / terminal assignment 1 form C, 1 CO contact, 3.2​mm 1 form A, 1 NO contact, 5​mm Dimensions 1 form C, 1 CO contact, 3.2​mm 2 01-2015, Rev. 0115 www.te.com © 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company. 1 form A, 1 NO contact, 5​mm Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. General Purpose Low Power PCB Relays Potter & Brumfield Low profile, PCB Relay T75 Series (Continued) Product code structure Typical product code T75 S 5 D 1 1 2 -12 Type T75 Low profile, printed circuit board relay T75 Series Enclosure S RTIII - wash tight Contact arrangement 1 1 form A, 1 NO 5 1 form C, 1 CO Coil input D DC voltage Coil Configuration 1 Single coil, monostable (non-latching) Mounting and terminals 1 PCB terminals Contact materials 2 AgCdO Coil voltage Coil code: please refer to coil versions table (e.g. 05=5VDC) Product code Arrangement Enclosure T75S1D112-05 1 form A, 1 NO RTIII - wash-tight T75S1D112-06 T75S1D112-12 T75S1D112-24 T75S5D112-05 1 form C, 1 CO T75S5D112-09 T75S5D112-12 T75S5D112-18 T75S5D112-24 T75S5D112-48 T75S5D112-60 01-2015, Rev. 0115 www.te.com © 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Coil 5VDC 6VDC 12VDC 24VDC 5VDC 9VDC 12VDC 18VDC 24VDC 48VDC 60VDC Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Part Number 1393222-7 5-1393223-2 2-1393222-9 4-1393222-8 7-1393222-6 9-1393222-0 1393223-3 1-1393223-6 2-1393223-8 4-1393223-1 1423089-1 Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. 3