2-1617076-2

CII Low Signal Relays Four Pole, Electrically Held, 2 Amps and Less (Continued) .150 Grid-space Relays Type 3SBH (4PDT) n Low profile… only 0.32 inches high n Long life version available n Qualified to MIL-R-39016/14 This .150 four pole double throw Grid-space relay is the companion to the two pole 3SBC type shown on page 1-41. It also features the same .150 inch pin spacing that allows you to insert the relay with no intermediate pin spreaders. There is adequate clearance for conductors to reach all pins. It is a very compact 4 pole double throw 2 ampere relay. Operating Characteristics Contact Ratings — DC resistive — 2 amps at 28 volts DC inductive — 0.5 amps at 28 volts, 200 mH AC resistive — 0.5 amps at 115 volts, 400 or 60 Hz (enclosure isolated from ground, or enclosure and movable contact at same potential) AC — 0.125 amps at 115 volts (enclosure at line potential with respect to movable contact) Low-level — low-level operation at 50 millivolts, 30 µA, 33 ohm miss level Contact Resistance — 0.050 ohms max.; 0.150 ohms after life test Life — 100,000 operations at rated loads listed; 1,000,000 operations at low-level loads Operate Time — 4 ms max. Release Time — 4 ms max. Contact Bounce — 1.5 ms Dielectric Strength — 500 volts rms at sea level; 350 volts rms at 70,000 feet Insulation Resistance — 1,000 megohms min. over temperature range 1 CII Low Signal Relays Product Facts Electrical Characteristics Environmental Characteristics Vibration — 30 G, to 3,000 Hz Shock — 100 G at 11 ms Temperature — -65°C to +125°C See page 1-57 for Mounting Forms, Terminals and Circuit Diagrams. *Values listed are factory test and inspection values. User should allow for meter variations. †Applicable over the operating temperature range in circulating air. Ordering Instructions Catalog-selected Relays: The catalog number is derived by choosing the proper CODE for each of the six relay characteristics in the order in which the codes are listed. Example: The relay selected in this example is a 4PDT .150-grid relay, voltage calibrated, end bracket mounting, 0.13 inch solder hook header, 720 ohms coil resistance, and 250 mW sensitivity. By choosing the proper code for each of these relay characteristics, the catalog number is identified as 3SBH5131K1. The letter R following sensitivity code indicates relay received 5000 operation miss-test. Ex. 3SBH5131K1R. * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1–55 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Low Signal Relays Four Pole, Electrically Held, 2 Amps and Less (Continued) .150 Grid-space Hybrid Relays Type 3SBH (4PDT) n Low profile… only 0.32 inches high steering diode prevents operation of the relay by reverse polarity voltages and protects the suppression diode. The single diode version is qualified to MIL-R-39016/53 and the dual diode is qualified to MIL-R-39016/54. n Long life version available Electrical Characteristics n Qualified to MIL-R-39016/53 & 54 Contact Ratings — DC resistive — 2 amps at 28 volts DC inductive — 0.5 amps at 28 volts, 200 mH AC resistive — 0.5 amps at 115 volts, 400 or 60 Hz (enclosure isolated from ground, or enclosure and movable contact at same potential) AC — 0.125 amps at 115 volts (enclosure at line potential with respect to movable contact) Low-level — 50 µA at 50mV Contact Resistance — 0.050 ohms max.; 0.150 ohms after life test Life — 100,000 operations at rated loads listed; 1,000,000 operations at low-level loads Product Facts The 4PDT .150 Grid-space hybrid relays are advanced designs of the standard high reliability 4PDT .150 Gridspace relays. In the single diode version, the relay coilback electromotive force is suppressed to prevent circuit/component damage. With the dual diode version, a steering diode is added to the coil circuit, along with the suppression diode. This Operating Characteristics Operate Time — 4 ms max. Release Time — 6 ms max. Contact Bounce — 2.0 ms Dielectric Strength (Note 1) — 500 volts rms at sea level; 350 volts rms at 70,000 feet Insulation Resistance (Note 1) — 1,000 megohms min. over temperature range Semiconductor Characteristics at 25°C Max. Negative Transient — 1 volt Breakdown Voltage — 100 Vdc @ 10 µA min. Max. Leakage Current — 1 µA @ 50 Vdc Note 1: Tests for dielectric withstanding voltage and insulation resistance should be made with “coil terminals” shorted together to avoid unnecessary electrical stress to semiconductor elements. See page 1-57 for Mounting Forms, Terminals and Circuit Diagrams. *Values listed are factory test and inspection values. User should allow for meter variations. †Applicable over the operating temperature range in circulating air. 1–56 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Low Signal Relays Four Pole, Electrically Held, 2 Amps and Less (Continued) Mounting Forms (3SBH) 1 CII Low Signal Relays (Vibration note with each form is acceleration from 55 to 3000 Hz) Header Types Header and Connection Diagrams Ordering Instructions Catalog-selected Relays: The catalog number is derived by choosing the proper CODE for each of the six relay characteristics in the order in which the codes are listed. Example: The relay selected in this example is a 4PDT .150-grid relay, voltage calibrated, end bracket mounting, 0.13 inch solder hook header, 720 ohms coil resistance, and 250 mW sensitivity. By choosing the proper code for each of these relay characteristics, the catalog number is identified as 3SBH5131K5. The letter R following sensitivity code indicates relay received 5000 operation miss-test. Ex. 3SBH5131K5R. * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com 1–57