2-1617162-0

CII Low Signal Relays Single Pole, Electrically Held, 1 Amp and Less (Continued) 1MAT 1MAT Standard TO-5 Diode Suppressed/ Transistor Driven High Performance Relay Qualified to MIL-R-28776/5 + X1 A2 XB – A1 X2 A3 XC Terminal View Product Facts Electrical Characteristics Contact Arrangement — 1 Form C (SPDT) Contact Material — Stationary — Gold/platinum/palladium/silver alloy (gold plated) Moveable — Gold/platinum/palladium/silver alloy (gold plated) Contact Resistance — Before Life — 100 milliohms max. (measured @ 10 mA @ 6 Vdc) After Life — 200 milliohms max. (measured @ 1 A @ 28 Vdc) Mechanical Life Expectancy — 1 million operations Coil Voltage — 5 to 26.5 Vdc Coil Power — 512 mW max. @ 25°C Duty Cycle — Continuous Pick-up Voltage — Approximately 50% of nominal coil voltage Pick-up Sensitivity — 100 mW max. @ 25°C n Transistor driver & suppression diode n Hermetically sealed n High shock & vibration ratings n Spreader pad n Excellent RF switching Contact Ratings Contact Load 1.0 A @ 28 Vdc 250 mA @ 115 Vac, 60 Hz & 400 Hz 100 mA @ 115 Vac, 60 Hz & 400 Hz 0.2 A @ 28 Vdc 0.1 A @ 28 Vdc 30 µA @ 50 mVdc 0.1 A @ 28 Vdc Operations MINd. 100,000 100,000 100,000 100,000 100,000 1,000,000 50,000 Type Resistive Resistive (case not grounded) Resistive Inductive (0.32 Henry) Lamp Low Level Intermediate Current .335 (8.51) DIA MAX .280 (7.11) MAX .370 (9.40) DIA MAX ± . .031 ± .003 (0.79) .035±.010 (0.89) TERMINALS W 1.500 MINd (38.1) C .500 MINd (12.7) P .187 ± .010 (4.75 ± .25) (Length excludes spreader pad) 36° ± 3° .200 (5.08) DIA (0.43) DIA ± 3°.017+.002 -.001 .370 (9.40) DIA MAX 1MAT Enclosure 1MAT Header 1-6 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Low Signal Relays Single Pole, Electrically Held, 1 Amp and Less (Continued) 1MAT (Continued) Environmental Characteristics Semiconductor Characteristics Timing — Operate Time — 2.0 ms max. Release Time — 4.0 ms max. Contact Bounce — 1.5 ms max Dielectric Withstanding Voltage — Between Open Contacts — 500 Vrms 60 Hz Between Adjacent Contacts — 500 Vrms 60 Hz Between Contacts & Coil — 500 Vrms 60 Hz Insulation Resistance — 10,000 megohms @ 500 Vdc 1,000 megohms @ 500 Vdc (coil to case @ +125°C) Temperature Range — -65°C to +125°C Weight — 0.08 oz. (2.27 grms) 0.09 oz. (2.52 grms) with spreader pad attached Vibration Resistance — 30 G’s, 10 to 3,000 Hz Shock Resistance — 75 G’s, 6 ±1 ms max. QPL Approval — MIL-R-28776/5 (J1MAT) Diode — 100 Vdc peak inverse voltage (PIV) 1.0 Vdc max. transient voltage Transistor — 0.3 Vdc MINd. base turn off voltage; 6.0 Vdc min. emitter-base breakdown voltage (BVEBO) @ 25°C; 80.0 Vdc min. collector-base breakdown voltage (BVCBO) @ 25°C & IC=100 µA 1 CII Low Signal Relays Operating Characteristics .103 (2.62) .014±.003 (0.36) 0.47 (1.19) DIA .370 (9.40) SQ MAX .100 (2.54) .100 (2.54) S W .140 – .175 DIA (3.56 – 4.45) Spreader & Mounting Pads Coil Data Nom. Coil Voltage (Vdc) 1MAT 5.0 6.0 9.0 12.0 18.0 26.5 Coil Resistance in Ohms ±10% @ 25°C (Note 1) Coil Circuit Current mA (Max.) (Note 1&2) Coil Circuit Current mA (MINd.) (Note 1&2) Pickup Voltage Vdc (Max.) @ 25°C (Note 2) Base Turn On Current mA (Max.) @ 25°C Pickup Voltage Vdc (Max.) @ 125°C (Note 2) 63 125 280 500 1,130 2,000 89.6 55.5 38.1 28.1 18.8 15.5 66.6 42.0 28.0 20.9 13.8 11.5 3.0 3.8 5.6 7.2 10.7 14.4 0.60 0.42 0.27 0.21 0.12 0.10 3.9 5.2 7.8 10.0 14.5 19.0 Drop-Out Drop-Out Nom. Coil Base Turn Voltage Voltage On Current Vdc Power (MINd.) Vdc (MINd.) mA (Max.) (mW) @ 25°C @ -65°C @ 125°C @ 25°C (Note 2) (Note 2) 2.38 1.60 1.07 0.80 0.53 0.40 0.24 0.31 0.47 0.62 0.94 1.25 0.15 0.18 0.35 0.40 0.58 0.89 397 288 289 288 287 351 Max. Coil Voltage Coil Desig. 5.8 8.0 12.0 16.0 24.0 32.0 5 6 9 12 18 26 Notes: 1. Coil resistance not directly measurable. Coil current should be within limits shown when tested at nominal voltage at 25°C for 5 seconds max. 2. Set base current at 3 mA to 15 mA during measurements. Ordering Instructions Catalog-selected Relays: The catalog number is derived by choosing the proper CODE for each of the relay characteristics in the order in which the codes are listed. Specifying a Part Number Example: Type Terminal Diodes Coils Spreader/Mounting Pads 1MA C T -26 S * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-7 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com