2-1879314-2

12mm Rotary Encoder with LED Type DPL12 Series Key Features 12mm rotary encoder Incremental type Push switch option Various shaft lengths LED color options Detent Options 12mm rotary incremental encoder with LED for use in electronic equipment. Can be supplied with or without switch with customization to standard options. Characteristics – Electrical Pulse Contact Rating Dielectric Strength Insulation Resistance (min) Operating Speed (RPM) Electrical Travel Rotational Noise Chattering 24 / 360° 0.5mA 5VDC 300VAC / 1mA, 1 minute MΩ at 5 VAC 60 RPM Continuous t2 = 2.0ms max (see below) t1 & t3 = 3.0ms max (see below) Code off Area V=3.5V or more Code on Area V=1.5V or less LED Color Options Switch Power Rating (where fitted) Switch contact Resistance Operating Temperature Storage Temperature 1-1773449-0 CIS WR 11/2016 Dimensions in millimetres unless otherwise specified With Switch – Dual color (see below) No Switch – Single color (see below) Switch – 1 = Blue / Green, 2 = Blue / Orange, 3 = Green / Red) No Switch – White, Red, Green, Blue 5VDC 10mA MΩ a . -10°C ~ +85°C -40°C ~ +70°C Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED Electrical Characteristics Item Conditions Specifications 2 Phase different signals (signal A & signal B) Details shown below (broken line shows detent position where fitted) A (Terminal A-C) C/W Output Signal Format B (Terminal B-C) A (Terminal A-C) C C/W B (Terminal B-C) Resolution Switching Characteristics Sliding Noise 1-1773449-0 CIS WR 11/2016 Number of pulses in 360° rotation 24 pulses / 360° each phase Measurement shall be made under the following conditions: 1. Shaft rotational speed: 360°/S 2. Test Circuit: See below Chattering Spe ified the sig al’s passage ti e from 3.5V to 1.5V or from 1.5V to 3.5V of each switching position (Code OFF → ON or ON →OFF NB To a oid hatteri g t₁ - t₃ please consider masking time and adding C/R filters to your circuit for pulse count design. Bounce Specified by the time of voltage change exceed 1.5V in code ON area. When the bounce has code ON time less than 1mS et ee hatteri gs t₁ or t₃ the voltage change shall be regarded as part of chattering, When the code ON time between two bounces is less than 1ms they are regarded as one linked bounce Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change t₁ , t₃ 3mS T ≤ S For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED Sliding Noise (continued) Sliding Noise The voltage change in OFF area 3.5V min. t₁ , t₃ Maski g ti e to a oid hatteri g Code OFF area – The area in which the voltage is 3.5V or more Code ON area – The area in which the voltage is 1.5V or less Measurement shall be made in the condition in which the shaft is rotated in 360° / S (constant speed) Rotational direction ΔT 3.5msec Phase Difference Insulation Resistance Dielectric Strength Number and position of detents Terminal Strength Rotation play at the click position 1-1773449-0 CIS WR 11/2016 Rotatio al Dire tio → Note: The test is conducted using equipment at constant speed 360°/ S according to spec. The test result could be different under manual conditions. In order to prove the interoperability between the firmware and the encoder please test the part in real conditions Measurement shall be made under the Between individual terminals condition which a voltage of 250V D.C and attaching Plate: MΩ is applied between individual terminals MIN and attaching plate A voltage of 300V A.C. shall be applied Without arcing or breakdown for 1 min or a voltage of 360 VA.C. shall be applied for 2 sec between individual terminals and attaching plate ( Leak current : 1mA ) 24 detents Step angle: 15°±3° Push and pull static load of 5Kgf shall be applied to the shaft in the axial direction for 10sec .( After soldering of the PC board ) Measure with jig for rotational angle Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change Without damage to. or excessive play in shaft .No excessive abnormality in rotational feeling and electrical characteristies shall be satisfied. 4°Max For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED Endurance Characteristics Item Rotational Life Conditions The shaft of the encoder shall be rotated to 30,000 cycles at a speed of 600 ~ 1000 cycles per hour without electrical load, after which measurement shall be made (1 cycle： rotate 360°C.C.W. rotate 360° C.W.) Specification Chattering: t1,t3 5ms Bounce: t2 3ms Phasedifference:△T 2.5msec Where applicable detent feeling remains. All electrical specification shall be met Soldering Condition Item Hand Soldering Dip soldering Conditions Bit temperature: 350°C or less Dwell time: 3S max. Preheating: PCB surface temp: 100°C or less Preheating time: 2 minutes Max. Soldering: Solder temperature: 260°C±5°C Immersion time: 5±1S 2 times max. Specifications There shall be no deformation or cracks in molded part. No excessive abnormality in rotational feeling Switch Electrical Characteristics (Where fitted) Item Contact resistance Chattering Insulation Resistance Dielectric Strength Switch rating (Resistor load) Note Conditions Measured by the electric current D.C. voltage drop method Switch is operated at the rate of 1 cycle 1 sec. The 1 cycle shall be OFF - ON - OFF Measurement shall be made under the condition which a voltage of 250V D.C. is applied between individual terminals and attaching plate. A voltage of 300V A.C. shall be applied for 1 min. or a voltage of 360V A.C. shall be applied for 2 sec between individual terminals and attaching plate. ( Leak current : 1mA ) Specification Ω MAX Less than 10 msec Between individual terminals and attaching plate. MΩ MIN . Without damage to parts arcing or breakdown. D.C.5V 10mA Shaft is insulated from switch terminal Switch Mechanical Characteristics (Where fitted) Item Contact arrangement Switching stroke 1-1773449-0 CIS WR 11/2016 Conditions Dimensions in millimetres unless otherwise specified Specification S.P.S.T Push On 0.5+0/-0.3mm Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED Switch Mechanical Characteristics (Continued) Item Switch strength Conditions Specification 450 ± 200gf Switch Endurance Characteristics Item Operating life Conditions The shaft of switch shall be operated 20,000 times without electronic load, after which measurements shall be made Specification Switch contact resistance : Ω MAX Switch strength: Relative to the previously Specified value +10% / -30%. Except above items specification as shown above LED Common Specifications Single color (No Switch) Circuit LED Characteristics Reverse Voltage: 5V Emitted Colour Red Lawn Green Blue Orange White Green Dark Orange 1-1773449-0 CIS WR 11/2016 Power Dissipation 60mW 100mW 72mW 100mW 72mW 72mW 100mW Dimensions in millimetres unless otherwise specified DC Forward Current 30mA 30mA 20mA 30mA 20mA 20mA 30mA Typ. 1.8 2 3.2 2.1 3.2 3.2 2.1 Dimensions Shown for reference purposes only. Specifications subject to change Test Conditions IF = 20mA Forward Voltage (V) Max. 2.6 2.6 3.6 2.6 3.6 3.6 2.6 For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED LED Common Specifications Dual color (Switch) Circuit LED Characteristics Reverse Voltage: 5V Power Dissipation (mW) Emitted Colour Blue / Orange Green / Red Blue / Green Red / Green Green / Orange Blue / Red White / Red White / Green Blue Orange Green Red Blue Green Red Green Green Orange Blue Red White Red White Green 75 60 95 60 75 95 60 95 95 60 75 60 75 60 75 60 DC Forward Current (mA) 20 25 25 25 20 25 25 25 25 25 20 25 20 25 20 25 Min. 2.7 1.7 2.7 1.7 2.7 2.7 1.7 2.7 2.7 1.7 2.7 1.7 2.7 1.75 2.7 1.7 Test Conditions IF = 20mA Forward Voltage (V) Typ. Max. 3.3 3.7 2 2.4 3.3 3.7 2 2.4 3.3 3.7 3.3 3.7 2 2.4 3.3 3.7 3.3 3.7 2 2.4 -3.3 -2.4 -3.7 -2.35 -3.7 -2.4 Dimensions DPL12V 1-1773449-0 CIS WR 11/2016 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED Dimensions DPL12H Dimensions DPL12SV Dimensions DPL12SH 1-1773449-0 CIS WR 11/2016 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help 12mm Rotary Encoder with LED Shaft Length – Without Switch Type K Dim L (from mounting surface) L (from mounting surface) F F Options (mm) 24 only 17.5 20 25 5 7 12 Shaft Length – With Switch Type K Dim L (from mounting surface) L (from mounting surface) F F Options (mm) 25 only 18.5 21 26 5 7 12 LED Color Codes Switch Option Code 1 2 3 4 5 6 7 8 R L B O W G D Switch (Dual Color) No Switch (Single Color) Description Blue / Green Blue / Orange Green / Red Red / Green Green / Orange Blue / Red White / Red White / Green Red Lawn Green Blue Orange White Green Dark Orange How To Order DPL12 Common Part DPL12 – No Switch DPL12S – Switch 1-1773449-0 CIS WR 11/2016 V Orientation N Detent 24 Pulses A Bush V – Vertical HHorizontal N– None 24 – 24 clicks 24 – 24 pulses 5mm Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change 20 Shaft Length See relevant table F Shaft Style F– Flatted KKnurled R LED Color See relevant table For Email, phone or live chat, go to: www.te.com/help