2-2316510-3

LUMAWISE DRIVE LED HOLDER TYPE Z50 TE Connectivity (TE)’s LUMAWISE drive LED Holder Type Z50 allows luminaire designers to remove driver boxes from spot and track lighting, creating a more aesthetically pleasing solution and removing cost from the system. The LUMAWISE drive Type Z50 brings integrated functionality to TE’s already successful, Zhaga inspired, Z50 range of LED holders. Incorporating a DC/DC driver into the holder itself provides a low profile constant current driver for CoBs, spot and track lighting. Designed for 48VDC input, it works with a wide range of readily available constant voltage power supplies meaning powering multiple fixtures off a single power supply is now possible. A 0-10V dimming option adds dimmability to the holder for added functionality. Applications Benefits • Track Lighting • Achieve an elegant luminaire design • Spot Lighting through a ‘Driver on Board’ solution • Downlights • Designed to meet the requirements of Mechanical • Dimensions: NEED PRODUCT GROUP PHOTO Zhaga book 12 Ø50mm, 7mm height • Electrical connection: 4-pin Mini CT connector 292228-4 • Mechanical connection: Mounting screws M3 or #4-40, 12mm length • Torque: 0.4 - 0.6 Nm • LED Outline and LES size 24x24, Ø21.5mm 20x24, Ø18.0mm 19x19, Ø17.7mm 16x19, Ø14.0mm • Provide thermal and electrical connection to four different CoB sizes: - 16x19mm - 20x24mm - 19x19mm - 24x24mm • Achieve design flexibility with an LED holder available with four different current outputs: • Form Factor Zhaga Book 12 Inspired - 350mA - 700mA • CoB thickness: Nominal 1mm - 500mA - 1050mA • CoB types: Both ceramic or aluminium types • IP rating: IP20 • Obtain added functionality with 0-10V dimming versions available • Mating connector flush with housing: Yes • Mating Cable Assembly: On/Off version: 1-2058943-8 0-10V version: 1-2058943-7 Specifications Materials • Standards: EN60838-2-2 EN61347-2-13 UL8754 UL8750 • Application Specification: 114-133082 • Environmental: RoHS and Reach compliant INTELLIGENT BUILDINGS /// LUMAWISE DRIVE LED HOLDER TYPE Z50 • Halogen free glass filled PBT housing • FR4 circuit board • Copper alloy electrical contacts LUMAWISE DRIVE LED HOLDER TYPE Z50 Electrical Thermal • Input voltage: 48VDC (European class I & II, SELV and US NEC class 2. Both with isolated output) • Maximum operating temperature: • Maximum input voltage: 60V (not recommended, contact TE) • Max Tc point temperature: 110°C (must not be exceeded) • Thermal protection mode: Yes: Output reduces to 20% regardless of dimming level • Over temperature reset (dimmable versions): After power cycle • Over temperature reset (on/off versions): After cooling down • Output current: 350mA 500mA 700mA 1050mA • Output current tolerance: ±5% • Forward voltage (Vf): 36VDC typical • Forward voltage (Vf) range: Min: 25VDC Max: 38VDC with 48VDC ±10% input 40VDC with 48VDC ±5% input 41VDC with 48VDC ±1% input • Dimming (dimming versions only): Source: 0-10V Sink: EN60929 annex E compatible dimmers Potentiometer: At 10VDC the external resistor value is 100kΩ. At 1VDC the external resistor value is 3.6kΩ • Dimming controller type: European class I & II or US NEC class 1&2. Both with basic isolation • Dim to off: No 125˚C (measured at equivalent Tc point) • Thermal interface material: Recommended: Use Laird PLC AS004444-25 • Storage temperature: -20˚C to 60˚C Optical • Optics: Compatible with TE’s Z50 optic clip type 1 and type 2 (part numbers: 2213194-1 and 2213349-1) • Allowable beam angle: 135˚ Other • Dimming curve: Linear (see Figure 1) • Diagnostic information: • Efficiency: Up to 94% at maximum output (see Figure 2) • EMC: IEC 61547, FCC title 47 (part 15 subpart B), CISPR15, EN55015 • Reverse polarity protected: Yes • Under voltage lock out protection: • Vibration: EIA 364-28, IEC 60512-6-4, IEC 60512-6-5 Yes: 42VDC - 37VDC • Input safety: Fused. Product fails safe when 230V applied • Mechanical shock: EIA 364-27 (test condition H), IEC 60512-6-3 • Noise: 30dB average • Thermal shock: EIA-364-32 (test condition VIII), IEC 60512-11-4 • Open/short circuit protection: Yes • Damp heat cycling: EIA-364-31 (method III), IEC 60512-11-3, IEC 60512-11-12 • Soft startup: 8ms (on/off), 90ms (dimmable) • Contact normal force: 500 hours at 125 °C • Minimum dim level: 3% of maximum output current • Flicker percentage: 0% (