2007626-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. TE CONNECTIVITY 1 D 3 MAX TYP DETAIL S SCALE 20:1 13 CAGE ASSEMBLY MATERIAL: NICKEL SILVER, 0.25 THICK HEAT SINK MATERIAL: ALUMINUM HEAT SINK CLIP MATERIAL: STAINLESS STEEL EMI SPRING MATERIAL: COPPER ALLOY FRONT FLANGE MATERIAL: ZINC ALLOY LIGHT PIPE MATERIAL: CLEAR POLYCARBONATE 2 PITCH BETWEEN PORTS OF ONE 1X4 CAGE ASSEMBLY. 3 SPACING BETWEEN CAGES ON THE SAME PC BOARD, TO BE SPECIFIED BY CUSTOMER, MUST COMPLY WITH MINIMUM DIMENSIONS SHOWN. 4 REFERENCE APPLICATION SPEC 114-13218 FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 5 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 6 DIMENSION C IS THE NOMINAL THICKNESS OF CUSTOMER SUPPLIED PC BOARD, SINGLE SIDED PC BOARD MINIMUM THICKNESS = 1.45mm DOUBLE SIDED PC BOARD MINIMUM THICKNESS = 2.2mm PER QSFP. 7 HEAT SINKS, LIGHT PIPES, AND CLIP SHIPPED ASSEMBLED TO CAGE ASSEMBLY. CAGE ASSEMBLY MAY BE PRESSED INTO THE PCB AS SHIPPED. 8 DATUM 9 DIMENSION APPLIES WITH MODULE INSERTED IN CAGE. -A- 1 REVISIONS DIST 00 P LTR DESCRIPTION DATE APVD D REVISED PER ECO-12-003841 14MAR2012 TY KS E REVISED PER ECO-12-005533 31MAR2012 JY AC F REVISED PER ECO-14-017735 3DEC2014 RG MC 15 2D BARCODE AND DATE CODE (YYWWD) MARKED ON SIDE OF CAGE ASSEMBLY. 16 REFERENCE APP SPEC 114-13218 FOR GASKET THICKNESS CALCULATION. 17 EMI SPRING FINISH: 2µm MINIMUM TIN FRONT FLANGE FINISH: 3µm MINIMUM TIN OVER 1.27µm MINIMUM NICKEL OVER 5.08µm MINIMUM COPPER HEAT SINK FINISH: NICKEL. 18 DWN D HEAT SINKS AND CLIPS SHIPPED ASSEMBLED TO CAGE ASSEMBLY. CAGE ASSEMBLY MAY BE PRESSED INTO THE PCB AS SHIPPED. LIGHT PIPES, SHIPPED UNATTACHED, MUST BE ASSEMBLED BY CUSTOMER AFTER THE CAGE IS SEATED IN THE PCB. IS TOP SURFACE OF PC BOARD. 10 UNPLATED THRU HOLE. 11 MAXIMUM HEIGHT OF LED OFF BOARD: 0.9mm. 12. MATES WITH QSFP MSA COMPATIBLE TRANSCEIVER. 13 SURFACE TRACES PERMITTED WITHIN THIS AREA EXCEPT WHERE CAGE STANDOFFS, SHOWN IN DETAIL S, CONTACT PC BOARD. 14 BASELINE FOR THESE DIMENSIONS IS THE CENTER OF COMPLIANT PIN HOLE. C C ( 60.57 ) 9 ( 79 ) ( 1.66 ) B MAX 2.2 MAX SEE DETAIL S 2D BARCODE AND DATE CODE 15 3X ( 19 ) 2 B B EMI SPRINGS 18 7 CAGE ASSEMBLY 7 A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm FRONT FLANGE MATERIAL 4805 (3/11) -1 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.1 0.1 - 17 DWN 28FEB2008 CHK 28FEB2008 APVD 28FEB2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - - WEIGHT 13.7 CUSTOMER DRAWING 2007626-3 SAN 2007626-1 23.0 NETWORKING B HEAT SINK PROFILE 16.0 2007626-2 PART NUMBER A TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ SQUARE LIGHT PIPES AND HEAT SINKS, QSFP SIZE - PCI CAGE CODE A1 00779 DRAWING NO 2007626 SCALE 1:1 SHEET 1 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION TE CONNECTIVITY 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN - - 7 SQUARE DOUBLE LIGHT PIPES QUANTITY: 4 APVD - 18 D D HEAT SINK CLIPS QUANTITY: 4 7 18 C C 72 PIN HEAT SINKS QUANTITY: 4 7 18 B B 1X4 BEHIND BEZEL QSFP CAGE ASSEMBLY QUANTITY: 1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 28FEB2008 CHK 28FEB2008 APVD 28FEB2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - - WEIGHT TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ SQUARE LIGHT PIPES AND HEAT SINKS, QSFP SIZE - CUSTOMER DRAWING CAGE CODE A1 00779 DRAWING NO 2007626 SCALE 1:1 SHEET 2 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION TE CONNECTIVITY 6 5 4 3 2 2008 LOC REVISIONS DIST GP ALL RIGHTS RESERVED. 1 00 P LTR - 79.5 DATE SEE SHEET 1 DWN APVD - - - 3 0.1 MIN 31.58 6.16 DESCRIPTION TYP 12.58 TYP OUTLET FOR 2.8 # 0.1 SQUARE LIGHT PIPE LENS. TYP 48 .25 MAX 5.2 MAX D R0.3 MAX TYP 9.7 BEZEL 13.35 0.1 TYP 0.2 TYP 11 0.3 0.2 (0.4 # 0.1 FOR PCI APPLICATIONS) 76.5 D 37 MAX 0.1 TYP GAP FOR EMI GASKET PROVIDED BY CUSTOMER GUIDE POSTS PER SPEC 16 ONE SIDED CONFIGURATION SCALE 5:2 C C 0.3 B 0.2 B (C+13.95) # 0.1 (C+0.4) # 0.1 C 6 (THICKNESS OF PC BOARD) BELLY TO BELLY CONFIGURATION SIMILAR TO ONE SIDED EXCEPT WHERE NOTED SCALE 5:2 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 28FEB2008 CHK 28FEB2008 APVD 28FEB2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - - WEIGHT TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ SQUARE LIGHT PIPES AND HEAT SINKS, QSFP SIZE - CUSTOMER DRAWING CAGE CODE A1 00779 DRAWING NO 2007626 SCALE 4:1 SHEET 3 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. TE CONNECTIVITY 1 REVISIONS DIST 00 P LTR - 76.2 M SEE DETAIL 14 19 19 n 1.55 - M 10:1 0.1 MAX 4X 12.58 0.05 J SEE DETAIL 13 4X 6.42 8X q OF LED 38X 0.8 TYP 8X 5.4 2X - - 18.5 14 14 8X APVD D -U10 SEE SHEET 1 DWN (1.05) 4 D DATE MAX DETAIL SCALE 17.38 DESCRIPTION 8 0.35 0.4 0.03 38X 1.8 0.03 1 4.5 2.5 11.3 MIN 10.3 MAX C C 4X 2X 0.8 MIN 40.68 3X 5.18 3.05 MAX 37.7 8X 30.1 1.69 MAX 0.89 3X 15.02 MIN 9 3X DETAIL J 3 PLACES SCALE 8:1 9 4.5 B 5 5 BSC B 1 MIN -X- 3.4 MIN 4X 4 MAX (1.05) -T- 5 4X BSC 1.1 -Y- 27X (1.05) TO q OF FIRST ROW OF HOLES FOR NEXT ADJACENT CAGE 17.9 4X 5 4 3 19 78 MIN CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) RECOMMENDED PC BOARD LAYOUT SINGLE SIDE MOUNT CONFIGURATION SCALE 4:1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 28FEB2008 CHK 28FEB2008 APVD 28FEB2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - - WEIGHT TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ SQUARE LIGHT PIPES AND HEAT SINKS, QSFP SIZE - CUSTOMER DRAWING CAGE CODE A1 00779 DRAWING NO 2007626 SCALE 1:1 SHEET 4 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. TE CONNECTIVITY 1 REVISIONS DIST 00 P LTR - 3.25 3.25 D (1.05) 4 15.25 2.13 15.75 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 3.25 D 15.75 15.25 -U4X 12.58 10 8X n 1.55 0.05 8X 4X 6.42 q OF LED K SEE DETAIL 8X 5.4 4.5 38X 0.35 0.03 0.8 TYP 38X 1.8 0.03 0.4 C C 2.5 8X 40.68 37.7 5.18 8X 30.1 1 7X B 5 5 4.5 BSC -X- 3.4 MIN 4 (1.05) B DETAIL K SCALE 8:1 4X 5 BSC 1.1 4X 8 51X (1.05) 4 3 TO q OF FIRST ROW OF HOLES FOR NEXT ADJACENT CAGE 17.9 -T5 -Y- 4X 19 RECOMMENDED PC BOARD LAYOUT BELLY TO BELLY CONFIGURATION SEE SHEET 4 FOR COMPONENT AND TRACE KEEPOUTS. SCALE 4:1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 28FEB2008 CHK 28FEB2008 APVD 28FEB2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - - WEIGHT TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ SQUARE LIGHT PIPES AND HEAT SINKS, QSFP SIZE - CUSTOMER DRAWING CAGE CODE A1 00779 DRAWING NO 2007626 SCALE 4:1 SHEET 5 RESTRICTED TO OF - 5 REV F