201M132-62J

CODE 54 - HEAT SHRINK BOOT BACKSHELL 201M116-19C-D SERIES DASH NUMBER (TABLE 1) MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 MODIFICATION CODE REFER TO CH00-0250-004 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-004. 3. ADAPTOR TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-201M112-19A). 4. BACKSHELL MATES TO MIL-C-81703, SERIES III, MS3424, MS3446, MS3464, MS3467, MS3468, CLASS E & L 5. BACKSHELL MATES TO MIL-C-5015G, MS3400 SERIES, CLASS D, E, K, L, U & W, MS3400, MS3401, MS3404, MS3406,MS3450, MS3451, MS3454, MS3456, MS3470, MS3471, MS3472, MS3474, MS3475, MS3476. MIL-C-83723, SERIES II, CLASS A & L. MIL-C-83723, SERIES I & III, CLASS A, G, K, R & S: M83723/1, /2, /3, /4, /5, /6, /7, /8, /13, /14, /36, /37, /38, /40, /41, /42, /43, /48, /49, /65, /66, /67, /68, /69, /70, /71, /72, /73, /74, /75, /76, /77, /78, /82, /83, /84, /85, /86, /87, /91, /92, /95, /97, /98, (MS3155 CONTROLLED INTERFACE). 6. WHEN "L" MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 WIRE HOLES, 120° APART. If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 19/02/2015 CHECKED 19/02/2015 APPROVED K.SHEPPARD 03/03/2015 APPROVED H.SMITH 20/08/2015 REVISIONS LTR DESCRIPTION J2 REVISED PER ECO-15-004707 K REVISED PER ECO-15-011999 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 26/03/2015 20/08/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H.SMITH H.SMITH TITLE: HEAT SHRINK BOOT BACKSHELL ASSY USED ON: MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 201M1XX K 1 A-A E REF. 26,90 MAX A G ØY ØZ XXXX STAINLESS STEEL TEETH VIEW A THREAD ØB X 3,50 PART MARK HERE A TABLE 1 BASE PART NUMBER 201M103 201M108 201M110 201M112 201M114 201M116 201M118 201M120 201M122 201M124 201M128 201M132 201M136 201M140 201M144 201M148 201M161 SHELL SIZE 03 08 10 12 14 16 18 20 22 24 28 32 36 40 44 48 61 MEDIUM DIAMOND KNURL 6 A THREAD 9/16 -24UNEF 1/2 -20UNF 5/8 -24UNEF 3/4 -20UNEF 7/8 -20UNEF 1 -20UNEF 1 1/16 -18UNEF 1 3/16 -18UNEF 1 5/16 -18UNEF 1 7/16 -18UNEF 1 3/4 -18UNS 2 -18UNS 2 1/4 -16UN 2 1/2 -16UN 2 3/4 -16UN 3 -16UN 1 1/2 -18UNEF ØB MAX 17,0 15,6 18,6 21,7 24,9 28,2 30,9 34,1 37,3 40,4 50,0 56,3 62,7 69,0 75,4 81,7 42,0 ØZ MIN 6,6 6,6 9,3 12,8 14,7 17,8 19,8 23,0 26,2 29,1 35,1 41,3 46,8 52,2 58,7 65,1 30,1 ØY X +0,00/-0,50 +0,20/-0,00 13,5 1,12 13,5 1,12 15,4 1,12 19,7 1,12 21,3 1,12 24,5 1,12 26,5 1,12 30,9 1,75 34,4 1,75 36,8 1,75 43,4 1,75 48,7 2,20 55,1 2,20 61,0 2,20 67,5 2,20 73,8 2,20 38,8 1,75 G 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 14,5 14,5 14,5 14,5 14,5 10,5 E REF. 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 32,3 32,3 32,3 32,3 32,3 28,0 If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 19/02/2015 CHECKED 19/02/2015 APPROVED K.SHEPPARD 03/03/2015 APPROVED H.SMITH 20/08/2015 REVISIONS LTR DESCRIPTION J2 REVISED PER ECO-15-004707 K REVISED PER ECO-15-011999 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 26/03/2015 20/08/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H.SMITH H.SMITH TITLE: HEAT SHRINK BOOT BACKSHELL ASSY USED ON: MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 201M1XX K 2