203M012-19C03-CS5567

CODE 54 - BRAID TAIL BACKSHELL 203M016-19B08-L SERIES ORDER NUMBER (TABLE 1) MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 ENTRY SIZE (TABLE 2) MODIFICATION CODE REFER TO CH00-0250-004 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-004 3. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-203M016-19B08). 4. WHEN ENTRY SIZE EXCEEDS "MAX ENTRY", A 2 PIECE BACKSHELL (TYPE 2) IS SUPPLIED. 5. BRAID TERMINATION RING MAY BE SUPPLIED AS TINEL-LOCK SHAPE MEMORY RING AT MANUFACTURERS OPTION. 6. BACKSHELL MATES TO MIL-C-81703, SERIES III, MS3424, MS3446, MS3464, MS3467, MS3468, CLASS E & L 7. BACKSHELL MATES TO MIL-C-5015G, MS3400 SERIES, CLASS D, E, K, L, U & W, MS3400, MS3401, MS3404, MS3406,MS3450, MS3451, MS3454, MS3456, MS3470, MS3471, MS3472, MS3474, MS3475, MS3476. MIL-C-83723, SERIES II, CLASS A & L. MIL-C-83723, SERIES I & III, CLASS A, G, K, R & S: M83723/1, /2, /3, /4, /5, /6, /7, /8, /13, /14, /36, /37, /38, /40, /41, /42, /43, /48, /49, /65, /66, /67, /68, /69, /70, /71, /72, /73, /74, /75, /76, /77, /78, /82, /83, /84, /85, /86, /87, /91, /92, /95, /97, /98, (MS3155 CONTROLLED INTERFACE). 8. WHEN "L" MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 WIRE HOLES, 120° APART. DRAWN K.WINCZURA DATE CHECKED 19/01/2015 APPROVED K.SHEPPARD 29/01/2015 APPROVED H.SMITH 3RD ANGLE PROJECTION NOT TO SCALE 19/01/2015 01/10/2015 REVISIONS LTR DESCRIPTION R REVISED PER ECO-15-002225 S REVISED PER ECO-15-013980 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DA TE 19/02/2015 01/10/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H . S MI T H H.SMITH TITLE: BRAID TAIL BACKSHELL (CODE 54) ASSY USED ON: MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 203M0XX S 1 IF MAX ENTRY IS EXCEEDED BACKSHELL WILL BE SUPPLIED AS TYPE 2 PART MARK HERE DRAWN K.WINCZURA DATE 19/01/2015 APPROVED K.SHEPPARD 29/01/2015 H.SMITH 01/10/2015 REVISIONS LTR DESCRIPTION R REVISED PER ECO-15-002225 S REVISED PER ECO-15-013980 A THREAD 9/16-24 UNEF 1/2-20 UNF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/16-18 UNEF 1 3/16-18 UNEF 1 5/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 2 3/4-16 UN 3-16UN 1 1/2-18 UNEF 3RD ANGLE PROJECTION NOT TO SCALE 19/01/2015 CHECKED APPROVED SHELL SIZE 6 7 3 8 & 8S 10 10, 10S, 10SL 7 12 & 12S 12 14 & 14S 19 16 & 16S 27 18 37 20 22 24 28 32 36 40 44 48 61 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DA TE 19/02/2015 01/10/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H . S MI T H H.SMITH ØB MAX 17,0 15,6 18,6 21,7 24,9 28,2 30,9 34,1 37,3 40,4 50,0 56,3 62,7 69,0 75,4 81,7 42,0 XXXX ØB PART MARK HERE 4 TINNED COPPER SHIELD STRAIGHT BACKSHELL - TYPE 2 STRAIGHT BACKSHELL - TYPE 1 TABLE 1 ORDER NUMBER 03 08 10 12 14 16 18 20 22 24 28 32 36 40 44 48 61 152,40 MIN ØY TINNED COPPER SHIELD A THREAD ØZ XXXX ØY ØK 152,40 MIN A THREAD ØB 25,50 23,50 MAX ØZ 16,80 `0,50 STAINLESS STEEL TEETH VIEW MAX ENTRY 04 04 06 08 09 11 12 14 16 18 22 24 28 28 28 28 18 TABLE 2 ENTRY SIZE 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 20 21 22 24 28 ØK MAX NA NA 21,0 21,0 21,0 24,5 24,5 29,0 29,0 32,5 35,5 35,5 37,0 37,0 40,0 40,0 43,5 48,5 48,5 52,1 58,5 ØZ REF 4,77 6,35 7,92 9,52 11,12 12,70 14,27 15,87 17,47 19,05 20,62 22,23 23,82 25,40 26,98 28,60 31,80 33,34 35,00 38,10 44,45 ØY REF 13,1 13,1 13,1 17,9 17,9 17,9 17,9 24,2 24,2 24,2 24,2 30,6 30,6 30,6 33,2 33,2 42,0 42,0 42,0 42,0 49,0 TITLE: BRAID TAIL BACKSHELL (CODE 54) ASSY USED ON: MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 203M0XX S 2