2057085-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 1 2 D RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR DESCRIPTION A A1 MATERIAL: CAGE ASSEMBLY: 0.25mm THICK NICKEL SILVER ALLOY GASKET RETENTION PLATE: STAINLESS STEEL EMI GASKET: PLATED FILLED SILICONE HEATSINK: ALUMINUM HEATSINK CLIP: STAINLESS STEEL DWN APVD RELEASED PER ECO-10-025263 10FEB2011 CJV JTL REVISED PER ECR-19-005696 09APR2019 IT SH 10 HEATSINK CLIP 2057118-1 49.15 MAX FINISH: HEATSINK: ELECTROLESS NICKEL FOR 2057085-1 THRU -3 HEATSINK: HARD COAT ANODIZED FOR 2057085-4 HEATSINK CLIP: PASSIVATE DATE 10 11 HEATSINK 3. MATES WITH SFP MSA COMPLIANT TRANSCEIVERS. D 4 PADS AND VIAS CHASSIS GROUND. 5 DATUM AND BASIC DIMENSION ESTABLISHED BY CUSTOMER. 6 MINIMUM PC BOARD THICKNESS: SINGLE SIDED = 1.45 7 REFERENCE APPLICATION SPEC. 114-13120, HOLE A, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 8 REFERENCE APPLICATION SPEC. 114-13120, HOLE B, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 9 10 11 C 12 X MAX CAGE ASSEMBLY 2057086-1 DIMENSIONS APPLIES PRIOR TO INSERTION OF SFP MODULE. HEATSINK CLIP AND HEATSINK SHIPPED UNASSEMBLED TO CAGE ASSEMBLY, CAGE ASSEMBLY TO BE PRESSED INTO THE PCB PRIOR TO ATTACHING THE HEATSINK CLIP AND HEATSINK TO THE CAGE ASSEMBLY. HEATSINK REFERENCE PART NUMBERS: 1829903-2 = 4.2mm HIGH - PCI,PIN TYPE. 1829904-2 = 6.5mm HIGH - SAN,PIN TYPE 1829905-2 = 13.5mm HIGH - NETWORKING, ELECTROLESS NICKEL,PIN TYPE 1829905-4 = 13.5mm HIGH - NETWORKING, HARD COAT ANODIZED,PIN TYPE 1963832-2 = 3.2mm HIGH - BLADE,PIN TYPE 2170426-4 = 4.2mm HIGH - PCI,FIN TYPE. 2170427-4 = 6.5mm HIGH - SAN,FIN TYPE 2170428-4 = 13.5mm HIGH - NETWORKING, FIN TYPE 2170429-2 = 3.2mm HIGH - BLADE,FIN TYPE 2057085-2/3/4/5/7/8/9, 1-2057085-3 RIGHT SIDE VIEW HEATSINK 10 10 HEATSINK CLIP 2057118-1 49.15 MAX HEATSINK CLIP AND HEATSINK SHIPPED ASSEMBLED TO CAGE ASSEMBLY. X MAX 14 0.1 PORT OPENING 9 CAGE ASSEMBLY 2057086-1 11 C 2057085-1 SCALE 4:1 APPROXIMATE LOCATION OF DATE CODE LABEL ( 48.7 ) B B 2057085-1/6 RIGHT SIDE VIEW 38.9 19.5 MIN 0.3 12 TYP A 15.45 TYP ( 35.4 ) ) MIN PCB THICKNESS CAGE PACKAGE 2057085-1 MOUNTED ON PCB SHOWN THRU RECOMMENDED BEZEL SCALE 4:1 mm MATERIAL 2057085-9 SAN 15.8 PIN TYPE NETWORKING, HARD COAT ANODIZED PIN TYPE PCI 22.8 2057085-8 12.5 2057085-6 2057085-7 13.5 2057085-5 22.8 2057085-4 NETWORKING, ELECTROLESS NICKEL 22.8 2057085-3 PIN TYPE SAN BLADE 15.8 12.5 2057085-2 HEAT SINK APPLICATION X PART NUMBER TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES 0.1 0.1 0.1 0.05 0.05 FINISH 1 13.5 BLADE THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PCI FIN TYPE PIN TYPE 6 ( 1.45 1-2057085-3 NETWORKING, PIN TYPE +0.10 0.23 -0.14 TOP OF PCB TO INSIDE OF BEZEL CUT-OUT 22.8 FIN TYPE FIN TYPE 10 10.4 NETWORKING, ELECTROLESS NICKEL PIN TYPE FIN TYPE GUIDE PINS R 0.3 MAX TYP RECOMMENDED BEZEL CUT-OUT SCALE 3:1 2057085-6 SCALE 4:1 ( 48.7 ) 8.95 0.15 PORT OPENING AMP 4805 REV 31MAR2000 9 2 DWN 22APR2008 CHK 22APR2008 APVD 22APR2008 Z.M.REAM M.R.SCHMITT R.H.WERTZ PRODUCT SPEC - 2057085-1 Tyco Electronics Harrisburg, PA 17105-3608 NAME SFP+ EHHANCED CAGE ASSEMBLY PRESS FIT, EMI GASKET, W/ HEAT SINK APPLICATION SPEC - 114-13120 WEIGHT - Customer Drawing SIZE CAGE CODE A1 00779 DRAWING NO RESTRICTED TO 2057085 SCALE 6:1 SHEET 1 OF - 2 REV A1 A 7 8 3 2 LOC 2X THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND 6X REVISIONS 00 P LTR DESCRIPTION - DATE SEE SHEET 1 DWN APVD - - - 10.93 8.13 7( n 1.05 ) 4 1 DIST GP 11.925 20 4 ALL RIGHTS RESERVED. 2X COPYRIGHT BY TYCO ELECTRONICS CORPORATION. 5 20 2.325 C RELEASED FOR PUBLICATION 7.125 THIS DRAWING IS UNPUBLISHED. 6 3.33 1.4 2.8 PLATING REQUIRED D D 37.1 35.5 SEE DETAIL 32.5 2X 1.55 35 0.05 -E- J 20 31.6 30.9 1.55 30 10X 4.1 11 0.05 -D- 28.3 27.5 25 23.75 10 1 SEE DETAIL K 20X 2 10X 4.1 0.05 C C 21.7 20 3X 42.3 18.4 3X 41.3 16.7 15 20X 0.5 18X 0.03 0.8 13.4 1 11.7 12.25 10 26.8 8.4 21.6 6.8 B DETAIL J RECOMMENDED PT CONNECTOR LAYOUT SCALE 12:1 B 12.05 1.1 5 CROSS-HATCHED AREA DENOTES EXPOSED CHASSIS GROUND 3.5 1.7 0 1.3 4.5 MAX -A- 24X 1 0 ( n1.05 ) A BSC 5 -B- 5 4 PLATING REQUIRED -C- 4 8( n 0.95 ) DETAIL K SCALE 18:1 PLATING REQUIRED A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 16.25 RECOMMENDED PCB CONFIGURATION WITH KEEP-OUT AREAS 6 SINGLE SIDED APPLICATIONS SCALE 9:1 AMP 4805 REV 31MAR2000 o2 20X 7 12X 14.25 5.75 MIN 2 DIMENSIONS: mm MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 0.1 0.05 0.05 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 22APR2008 CHK 22APR2008 APVD 22APR2008 Z.M.REAM M.R.SCHMITT R.H.WERTZ PRODUCT SPEC - Tyco Electronics Harrisburg, PA 17105-3608 NAME SFP+ EHHANCED CAGE ASSEMBLY PRESS FIT, EMI GASKET, W/ HEAT SINK APPLICATION SPEC - 114-13120 WEIGHT - Customer Drawing SIZE CAGE CODE A1 00779 DRAWING NO RESTRICTED TO 2057085 SCALE 6:1 SHEET 2 OF - 2 REV A1