2057183-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION 6 5 4 3 2 2008 LOC BY - 1 D 3 MAX TYP DETAIL S SCALE 20:1 12 CAGE ASSEMBLY MATERIAL: NICKEL SILVER, 0.25 THICK HEAT SINK MATERIAL: ALUMINUM HEAT SINK CLIP MATERIAL: STAINLESS STEEL EMI SPRING MATERIAL: COPPER ALLOY FRONT FLANGE MATERIAL: ZINC ALLOY LIGHT PIPE MATERIAL: CLEAR POLYCARBONATE 2 PITCH BETWEEN PORTS OF ONE 1X4 CAGE ASSEMBLY. 3 SPACING BETWEEN CAGES ON THE SAME PC BOARD, TO BE SPECIFIED BY CUSTOMER, MUST COMPLY WITH MINIMUM DIMENSIONS SHOWN. 4 REFERENCE APPLICATION SPEC 114-13218 FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 5 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 6 DIMENSION F IS THE NOMINAL THICKNESS OF CUSTOMER SUPPLIED PC BOARD, SINGLE SIDED PC BOARD MINIMUM THICKNESS = 1.45mm DOUBLE SIDED PC BOARD MINIMUM THICKNESS = 2.2mm PER QSFP. 7 HEAT SINKS, LIGHT PIPES, AND HEAT SINK CLIPS SHIPPED ASSEMBLED TO CAGE ASSEMBLY. CAGE ASSEMBLY MAY BE PRESSED INTO THE PCB AS SHIPPED. 8 DATUM 9 DIMENSION APPLIES WITH MODULE INSERTED IN CAGE. 10 -A- REVISIONS DIST GP ALL RIGHTS RESERVED. 1 00 P LTR DESCRIPTION DATE APVD C REVISED PER ECO-10-018054 04NOV2010 CJV EJB D REVISED PER ECO-12-003481 15MAR2012 KS AC E REVISED PER ECO-12-005533 31MAR2012 JY AC F REVISED PER ECO-14-017735 3DEC2014 RG MC 15 REFERENCE APP SPEC 114-13218 FOR GASKET THICKNESS CALCULATION. 16 EMI SPRING FINISH: 2µm MINIMUM TIN FRONT FLANGE FINISH: 3µm MINIMUM TIN OVER 1.27µm MINIMUM NICKEL OVER 5.08µm MINIMUM COPPER. HEAT SINK FINISH: NICKEL 17 DWN D HEAT SINKS AND CLIPS SHIPPED ASSEMBLED TO CAGE ASSEMBLY. CAGE ASSEMBLY MAY BE PRESSED INTO THE PCB AS SHIPPED. LIGHT PIPES, SHIPPED UNATTACHED, MUST BE ASSEMBLED BY CUSTOMER AFTER THE CASE IS SEATED IN THE PCB. IS TOP SURFACE OF PC BOARD. UNPLATED THRU HOLE. 11. MATES WITH QSFP MSA COMPATIBLE TRANSCEIVER. 12 SURFACE TRACES PERMITTED WITHIN THIS AREA EXCEPT WHERE CAGE STANDOFFS, SHOWN IN DETAIL S, CONTACT PC BOARD. 13 BASELINE FOR THESE DIMENSIONS IS THE CENTER OF COMPLIANT PIN HOLE. 14 2D BARCODE AND DATE CODE (YYWWD) MARKED ON SIDE OF CAGE ASSEMBLY. C C ( 60.57 ) 9 ( 79 ) (D) B MAX 2D BARCODE AND DATE CODE 2.2 MAX (C) SEE DETAIL 14 S 2 3X ( 19 ) B 7 7 EMI SPRINGS 1.3-1.4 5.7 2.15 16.0 SAN 2057183-5 0.8-1.1 2.8 1.70 23.0 NETWORKING 2057183-3 2.8 1.70 13.7 PCI 1.3-1.4 17 CAGE ASSEMBLY B 5.7 0.8-1.1 7 2.8 0.8-1.1 17 E A mm FRONT FLANGE MATERIAL 4805 (3/11) -1 1.70 D THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: 2.15 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.1 0.1 - 16 C 01MAY2008 CHK 01MAY2008 APVD 01MAY2008 E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - 114-13218 WEIGHT PCI 16.0 - CUSTOMER DRAWING 2057183-4 SAN 2057183-2 2057183-1 HEAT SINK PROFILE B DWN C. VALENTINE 13.7 PART NUMBER A TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ LIGHT PIPES AND HEAT SINKS, QSFP SIZE CAGE CODE A1 00779 DRAWING NO 2057183 SCALE 4:1 SHEET 1 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION BY - 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN - - DOUBLE LIGHT PIPES QUANTITY: 4 7 APVD - 17 D D HEAT SINK CLIPS QUANTITY: 4 7 17 C C 72 PIN HEAT SINKS QUANTITY: 4 7 17 B B 1X4 BEHIND BEZEL QSFP CAGE ASSEMBLY QUANTITY: 1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 01MAY2008 CHK 01MAY2008 APVD 01MAY2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - 114-13218 WEIGHT - CUSTOMER DRAWING TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ LIGHT PIPES AND HEAT SINKS, QSFP SIZE CAGE CODE A1 00779 DRAWING NO 2057183 SCALE 4:1 SHEET 2 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION BY - 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR - 79.5 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 3 0.1 MIN 31.58 TYP 6.16 TYP 12.58 TYP 48.25 MAX 2.3 0.1 TYP LIGHT PIPE CUT-OUT 5.2 MAX BEZEL D 9.7 D 0.2 TYP 12.95 0.1 TYP R 0.3 MAX TYP 76.5 0.3 0.2 (0.4 # 0.1 FOR PCI APPLICATIONS) 0.1 TYP E NOMINAL LED HEIGHT 37 MAX GAP FOR EMI GASKET PROVIDED BY CUSTOMER GUIDE POSTS PER SPEC 15 C C ONE SIDED CONFIGURATION SCALE 5:2 0.3 0.2 12.95 0.1 TYP B B (F+13.55) # 0.1 TYP (F+0.4) # 0.1 F 6 (THICKNESS OF PC BOARD) BELLY TO BELLY CONFIGURATION SIMILAR TO ONE SIDED EXCEPT WHERE NOTED SCALE 5:2 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 01MAY2008 CHK 01MAY2008 APVD 01MAY2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - 114-13218 WEIGHT - CUSTOMER DRAWING TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ LIGHT PIPES AND HEAT SINKS, QSFP SIZE CAGE CODE A1 00779 DRAWING NO 2057183 SCALE 4:1 SHEET 3 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. BY - 1 REVISIONS DIST 00 P LTR - 76.2 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - MAX 13 19 17.38 M SEE DETAIL (1.05) 4 D 13 19 4X 12.58 13 4X 6.42 8X n 1.55 8X 12 0.05 M 10:1 D q OF LED J SEE DETAIL 8X 5.4 2X DETAIL SCALE AREA DENOTES COMPONENT KEEP-OUT (TRACES PERMITTED) -U10 18.5 0.1 MAX 38X 0.8 TYP 8 0.35 0.4 4.5 0.03 38X 1.8 0.03 1 11.3 MIN 10.3 MAX 2.5 C C 4X 2X 0.8 MIN 40.68 3X 5.18 37.7 3.05 MAX 8X 30.1 1.69 3X MAX 9 0.89 3X 15.02 MIN 9 DETAIL J 3 PLACES SCALE 8:1 4.5 B 5 5 BSC 1 MIN -X- 3.4 MIN 4X 4 (1.05) -T- 5 4X BSC 1.1 -Y- 27X (1.05) B 3 TO q OF FIRST ROW OF HOLES FOR NEXT ADJACENT CAGE 17.9 4X 5 4 MAX 19 78 MIN CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) RECOMMENDED PC BOARD LAYOUT SINGLE SIDE MOUNT CONFIGURATION SCALE 4:1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm THIS PRODUCT HAS NOT COMPLETED VALIDATION/QUALIFICATION TESTING MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 01MAY2008 CHK 01MAY2008 APVD 01MAY2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - 114-13218 WEIGHT - CUSTOMER DRAWING TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ LIGHT PIPES AND HEAT SINKS, QSFP SIZE CAGE CODE A1 00779 DRAWING NO 2057183 SCALE 4:1 SHEET 4 RESTRICTED TO OF - 5 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2008 RELEASED FOR PUBLICATION 6 5 4 3 2 2008 LOC GP ALL RIGHTS RESERVED. BY - 1 REVISIONS DIST 00 P LTR - 3.25 3.25 D 4 (1.05) 15.25 2.13 15.75 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 3.25 D 15.75 15.25 -U4X 12.58 10 8X n 1.55 0.05 8X 4X 6.42 q OF LED K SEE DETAIL 8X 5.4 4.5 38X 0.35 0.03 0.8 TYP 38X 1.8 0.03 0.4 C C 2.5 8X 40.68 37.7 5.18 8X 30.1 1 7X B 5 5 4.5 BSC -X- 3.4 MIN 4 (1.05) B DETAIL K SCALE 8:1 4X 5 BSC 1.1 4X 8 51X (1.05) 4 3 TO q OF FIRST ROW OF HOLES FOR NEXT ADJACENT CAGE 17.9 -T5 -Y- 4X 19 RECOMMENDED PC BOARD LAYOUT BELLY TO BELLY CONFIGURATION SEE SHEET 4 FOR COMPONENT AND TRACE KEEP-OUTS SCALE 4:1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 01MAY2008 CHK 01MAY2008 APVD 01MAY2008 C. VALENTINE E. BRIGHT E. BRIGHT PRODUCT SPEC 108-2286 APPLICATION SPEC - 114-13218 WEIGHT - CUSTOMER DRAWING TE Connectivity NAME 1X4 CAGE ASSEMBLY, BEHIND BEZEL, W/ LIGHT PIPES AND HEAT SINKS, QSFP SIZE CAGE CODE A1 00779 DRAWING NO 2057183 SCALE 4:1 SHEET 5 RESTRICTED TO OF - 5 REV F