208M710-19B06

CODE 54 - BRAID TAIL BACKSHELL 203M116-19B08-L SERIES DASH NUMBER (TABLE 1) MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 ENTRY SIZE (TABLE 2) MODIFICATION CODE REFER TO CH00-0250-004 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-004 3. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-203M116-19B08). 4. WHEN ENTRY SIZE EXCEEDS "MAX ENTRY", A 2 PIECE BACKSHELL (TYPE 2) IS SUPPLIED. 5. BRAID TERMINATION RING MAY BE SUPPLIED AS TINEL-LOCK SHAPE MEMORY RING AT MANUFACTURERS OPTION. 6. BACKSHELL MATES TO MIL-C-81703, SERIES III, MS3424, MS3446, MS3464, MS3467, MS3468, CLASS E & L 7. BACKSHELL MATES TO MIL-C-5015G, MS3400 SERIES, CLASS D, E, K, L, U & W, MS3400, MS3401, MS3404, MS3406,MS3450, MS3451, MS3454, MS3456, MS3470, MS3471, MS3472, MS3474, MS3475, MS3476. MIL-C-83723, SERIES II, CLASS A & L. MIL-C-83723, SERIES I & III, CLASS A, G, K, R & S: M83723/1, /2, /3, /4, /5, /6, /7, /8, /13, /14, /36, /37, /38, /40, /41, /42, /43, /48, /49, /65, /66, /67, /68, /69, /70, /71, /72, /73, /74, /75, /76, /77, /78, /82, /83, /84, /85, /86, /87, /91, /92, /95, /97, /98, (MS3155 CONTROLLED INTERFACE). 8. WHEN "L" MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 WIRE HOLES, 120° APART. If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 20/04/2015 CHECKED 20/04/2015 APPROVED K.SHEPPARD 27/04/2015 APPROVED H.SMITH 02/09/2015 REVISIONS LTR DESCRIPTION N1 REVISED PER ECO-12-011624 P REVISED PER ECO-15-012672 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 21/06/2012 02/09/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED K.YEE H.SMITH TITLE: BRAID TAIL BACKSHELL ASSY USED ON: MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 203M1XX P 1 IF MAX ENTRY IS EXCEEDED ADAPTER WILL BE SUPPLIED AS TYPE 2 16,80 `0,50 C A THREAD XXXX ØB ØK ØB Y Ø Ø Y Ø Ø Z Z XXXX IN M M IN 0 2, 40 ,4 15 2 15 A THREAD D G STAINLESS STEEL TEETH VIEW F PART MARK HERE PART MARK HERE NO PART MARK TINNED COPPER SHIELD TINNED COPPER SHIELD 45° - TYPE 1 TABLE 1 ORDER NUMBER 03 08 10 12 14 16 18 20 22 24 28 32 36 40 44 48 61 45° - TYPE 2 6 3 SHELL SIZE 7 10 7 12 19 27 37 8 & 8S 10, 10S, 10SL 12 & 12S 14 & 14S 16 & 16S 18 20 22 24 28 32 36 40 44 48 61 TABLE 2 ENTRY SIZE 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 20 21 22 24 28 ØK MAX NA NA 21,0 21,0 21,0 24,5 24,5 29,0 29,0 32,5 35,5 35,5 37,0 37,0 40,0 40,0 43,5 48,5 48,5 52,1 58,5 A THREAD 9/16-24 UNEF 1/2-20 UNF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/16-18 UNEF 1 3/16-18 UNEF 1 5/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 2 3/4-16 UN 3-16UN 1 1/2-18 UNEF ØZ REF 4,77 6,35 7,92 9,52 11,12 12,70 14,27 15,87 17,47 19,05 20,62 22,23 23,82 25,40 26,98 28,60 31,80 33,34 35,00 38,10 44,45 ØY REF 13,1 13,1 13,1 17,9 17,9 17,9 17,9 24,2 24,2 24,2 24,2 30,6 30,6 30,6 33,2 33,2 42,0 42,0 42,0 42,0 49,0 ØB MAX 17,0 15,6 18,6 21,7 24,9 28,2 30,9 34,1 37,3 40,4 50,0 56,3 62,7 69,0 75,4 81,7 42,0 C ±0,5 16,8 16,6 16,8 17,3 18,1 19,0 19,2 20,1 20,3 21,8 23,3 25,0 26,2 28,6 30,1 31,3 22,1 MAX ENTRY 04 04 06 08 09 11 12 14 16 18 22 24 28 28 28 28 18 F ±0,5 NA NA 12,5 12,5 12,5 13,1 13,1 13,5 13,5 14,5 15,5 15,5 16,1 16,1 16,5 16,5 17,0 18,5 18,5 21,9 25,7 D ±0,5 16,6 16,4 16,7 17,1 17,9 18,7 19,0 19,8 20,1 21,5 22,0 23,7 24,9 26,1 27,8 29,0 21,4 G ±0,5 NA NA 14,5 14,5 14,5 15,1 15,1 16,6 16,6 18,3 18,8 18,8 19,7 19,7 20,0 20,0 22,9 24,8 24,8 25,8 26,4 If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 20/04/2015 CHECKED 20/04/2015 APPROVED K.SHEPPARD 27/04/2015 APPROVED H.SMITH 02/09/2015 REVISIONS LTR DESCRIPTION N1 REVISED PER ECO-12-011624 P REVISED PER ECO-15-012672 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 21/06/2012 02/09/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED K.YEE H.SMITH TITLE: BRAID TAIL BACKSHELL (CODE 54) ASSY USED ON: MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 203M1XX P 2