209M414-19B

WHEN 'L' MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 LOCK WIRE HOLES, 120° APART 6 CODE 40 - HEAT SHRINK BOOT BACKSHELL 209M412-19B-DL SERIES ORDER NUMBER (TABLE 1) MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 MODIFICATION CODE REFER TO CH00-0250-004 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-004. 3. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-209M412-19B). 4. KNURL INSIDE BOOT GROOVE MAY BE SUPPLIED AT MANUFACTURER'S OPTION. 5. BACKSHELL MATES TO MIL-C-38999 SERIES III & IV, CLASS C, F, K AND W, D38999/20, /24, /26, /40, /46, /47 CONNECTORS AND WHEN SO MATED PROVIDE A WATER-TIGHT SEAL MEETING THE REQUIREMENTS OF MIL-C-85049, PAR. 3.5.7. 6. WHEN 'L' MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 LOCK WIRE HOLES, 120° APART. 7. THIS IS A FUNCTIONAL EQUIVALENT OF MIL-C-85049/69 8. WHEN GROUNDING SCREW MODIFICATION IS ORDERED 18,50 MAX BECOMES 27,20 MAX AND 25,50 MAX BECOMES 34,20 MAX DRAWN W.RUST DATE CHECKED 11/09/2015 APPROVED K.SHEPPARD 11/09/2015 APPROVED H.SMITH 3RD ANGLE PROJECTION NOT TO SCALE 11/09/2015 15/10/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-15-002406 J REVISED PER ECO-15-013980 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 19/02/15 APPROVED 15/10/2015 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 H.SMITH TITLE: HEAT SHRINK BOOT BACKSHELL ASSY USED ON: MIL-DTL-39888 SERIES III & IV TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 209M4XX J 1 WHEN 'L' MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 LOCK WIRE HOLES, 120° APART MEDIUM DIAMOND KNURL 25,50 MAX 8 18,50 MAX 8 A-A A 10,50 3,50 XXXX TABLE 1 BASE PART NUMBER 209M408 209M410 209M412 209M414 209M416 209M418 209M420 209M422 209M424 DRAWN W.RUST DATE 11/09/2015 APPROVED K.SHEPPARD 11/09/2015 H.SMITH 08 10 12 14 16 18 20 22 24 15/10/2015 REVISIONS DESCRIPTION LTR H REVISED PER ECO-15-002406 J REVISED PER ECO-15-013980 9/A 11 / B 13 / C 15 / D 17 / E 19 / F 21 / G 23 / H 25 / J 3RD ANGLE PROJECTION NOT TO SCALE 11/09/2015 CHECKED APPROVED ORDER.NO. SHELL SIZE 5 COM'L / MIL UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 19/02/15 APPROVED 15/10/2015 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 H.SMITH 4 DRAIN HOLES WHEN 'D' MODIFICATION IS SPECIFIED PART MARK HERE A ØY ØZ A THRAED ØB X SILICONE O-RING A THREAD ØB MAX X +0,20/-0,00 ØY MAX ØZ MIN M12 × 1.0 M15 × 1.0 M18 × 1.0 M22 × 1.0 M25 × 1.0 M28 × 1.0 M31 × 1.0 M34 × 1.0 M37 × 1.0 18,0 21,0 24,5 29,0 32,5 35,5 37,0 40,0 43,5 1,12 1,12 1,12 1,12 1,12 1,12 1,75 1,75 1,75 13,50 15,40 19,70 21,30 24,50 26,50 31,00 34,40 36,60 6,80 10,30 13,60 16,30 19,50 21,90 25,20 28,30 31,50 TITLE: HEAT SHRINK BOOT BACKSHELL ASSY USED ON: MIL-DTL-39888 SERIES III & IV TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 209M4XX J 2