2151279-1

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION DESCRIPTION FEED TYPE E FINE CRIMP HEIGHT ADJUST MECHANICAL 5-2151279-1 E SEAL STRIPPER CRIMPER TERMINATING UNIT MECHANICAL 5-2151279-2 F 7-2151279-1 E 7-2151279-2 F 7- 2151279 -7 A CRIMP WIRE INSUL FINE CRIMP HEIGHT ADJUST - TYPE 3 - TE TERMINAL WIRE STRIP LENGTH 4.00-4.60 mm [.157-.181 IN] C TERMINAL APPLICATION SPECIFICATION (A) 962943-2 (A) 962943-3 (A) 962943-4 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 n (A)114-18081 - TERMINALS APPLIED TE TERMINAL (A) 962943-1 TE CRIMP SPECIFICATION MICRO TIMER 2 CONTACT TERMINAL NAME: C1__DWG_PN_1_1 (A) 962943-6 C1__DWG_PN_1_2 (A) 968052-1 C1__DWG_PN_1_3 TERMINAL DATA: TERMINAL NAME: 1.40-2.10 mm [.055-.083 IN] - - - - TE TERMINAL 4.00-4.60 mm [.157-.181 IN] TERMINAL APPLICATION SPECIFICATION (B)114-18082 - TERMINALS APPLIED C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 C1__DWG_PN_2_3 (B)962948-1 (B)962948-2 (B)963900-1 (B)962900-2 n - TE CRIMP SPECIFICATION MICRO TIMER 2 CONTACT WIRE STRIP LENGTH INSULATION DIAMETER RANGE 5 TE TERMINAL (A) 962943-5 C1__DWG_PN_1_0 3 INSULATION DIAMETER RANGE - 1.40-2.10 mm [.055-.083 IN] - - - - - - - 5 5 (B)962900-3 (B)962900-4 - C1__DWG_PN_1_4 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.20+/-0.05 [.047+/-.002] 1.18+/-0.05 [.046+/-.002] 1.15+/-0.05 [.045+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 5.6 5.8 6.1 WIRE SIZE 4 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 1.00mm2 0.75mm2 0.50mm2 CRIMP HEIGHT mm [INCH] 1.38+/-0.05 [.054+/-.002] 1.29+/-0.05 [.051+/-.002] 1.20+/-0.05 [.047+/-.002] CRIMP HEIGHT 4 REFERENCE SETTING - 4.6 - - 3.8 - 5.6 - 1 B 2 3 4 5 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - TERMINAL LUBRICANT IS RECOMMENDED. 1 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. - 1 - 1 1 1 - A 1 1 1 1 - 1 1 1 1 1 1 - REF 1 1 1 1 1 1 1 1 2 1 1 1 4 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 - REF 1 1 1 1 1 1 1 1 2 1 1 1 4 2 1 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 - DESCRIPTION DATE DWN APVD D ECR-18-007903 23MAY2018 YY JDG E ECR-18-013630 27AUG2018 TB TE E1 ECR-18-019154 07DEC2018 JAH GB F ECR-19-009410 15JUN2019 TB TE 1 1 - - 1 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - PART NO - - - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 - 1 1 1 1 - 1 1 - 1 1 1 1 - 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 - 1 1 - - - 2 - 1 - 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: -1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1803515-3 2-1803583-1 2119641-1 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 4-1722335-3 1-5018030-0 1-1752354-9 993111-1 5-22280-0 1752353-3 1901680-2 994970-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119791-5 2119943-1 2119740-1 2168078-1 2168083-2 5-18022-5 1338685-1 2168083-3 2168083-3 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1-1752356-8 2079383-5 2-2844962-8 2844992-2 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 454276-5 1-1333204-5 240641-9 2119757-4 238011-4 4-2119784-0 455888-9 1-456405-6 - -77 -72 -71 -52 -51 -2 AMP 4805 REV 31MAR2000 LTR D - TERMINAL DATA: P - F O APPLICATOR INSTRUCTIONS 408-35042 66 PNEUMATIC CRIMP TOOLING KIT 2.54 mm [.100] REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT 2.03 mm [.080] 2 PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT SIZE 3 PNEUMATIC SEAL STRIPPER CRIMPER TERMINATING UNIT APPLICATOR DATA 4 LOC 2151279 -1 F 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2151279 -2 D 6 TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 09DEC2011 CHK 09DEC2011 APVD 09DEC2011 K.HUANG S.XI I.CRUZ - WEIGHT NAME SIZE - 1 2119082-8 1 2079764 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 4-1722335-3 1 1-5018030-0 1 1-1752354-9 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 1 COUNTER_994970 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1-1752356-8 2 2079383-5 2 2-2844962-8 1 2844992-2 1 1-455888-0 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 454276-5 1 1-1333204-5 1 240641-9 .. 1 ITEM_6 1 2119757-4 1 238011-4 1 4-2119784-0 1 455888-9 1 1-456405-6 ITEM NO OCEAN SIDE FEED APPLICATOR A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119641-1 293 292 248 244 243 242 241 239 238 182 181 180 177 176 175 174 164 113 99 98 82 71 70 69 67 66 60 59 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 Harrisburg, PA 17105-3608 - 1 2-1803583-1 TE Connectivity APPLICATION SPEC - 1 1803515-3 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH RAM ASSEMBLY, SF ATLANTIC APPLICATOR BASIC ASSEMBLY, SF FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DRAWING NO - RESTRICTED TO 2151279 SCALE 1:2 SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 56 44 PNEUMATIC 293 2 244 A 243 53 50 238 242 2 3 7 8 59 C 82 1 1 69 70 3 1 4 2 176 2 TERMINAL SUPPORT LOCATION 28 5 41 174 44 293 REF 181 2 44.61 175 182 DETAIL A 3 164 33 B 0.05 66 180 2 19.0 180 B 20 21 29 9 1 12 ITEM 30 LOCATED AT FRONT HOLES 241 13 CAM POSITIONS 30mm STROKE 30mm STROKE 47 113 5 98 99 46 292 34 54 8 1 60 54 10 1 20 30 REF 29 REF 1 11 248 48 REF RAM AND HOLDDOWN SET-UP 19 30 30mm STROKE 0.5 67 A 24 0.5 C 2 177 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2.4 34 REF SEE DETAIL A 56 REF FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 09DEC2011 CHK 09DEC2011 APVD 09DEC2011 K.HUANG S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN OCEAN SIDE FEED APPLICATOR - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 DRAWING NO - RESTRICTED TO 2151279 SCALE 1:2 SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151279 -1 E FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151279 -7 A CRIMP TOOLING KIT - F 3 2 LOC PART NUMBER 2- 2151279 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE F O 2.03 mm [.080] 2.54 mm [.100] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 4.00-4.60 mm [.157-.181 IN] TERMINAL APPLICATION SPECIFICATION (A) 962943-1 (A) 962943-2 (A) 962943-3 (A) 962943-4 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 n (A)114-18081 - TERMINALS APPLIED TE TERMINAL TE CRIMP SPECIFICATION MICRO TIMER 2 CONTACT TERMINAL NAME: C TYPE (A) 962943-5 (A) 962943-6 C1__DWG_PN_1_1 C1__DWG_PN_1_2 (A) 968052-1 C1__DWG_PN_1_3 TERMINAL NAME: 1.40-2.10 mm [.055-.083 IN] - - - - TE TERMINAL 4.00-4.60 mm [.157-.181 IN] TERMINAL APPLICATION SPECIFICATION (B)114-18082 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL (B)962948-1 (B)962948-2 (B)963900-1 (B)962900-2 C1__DWG_PN_4_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 C1__DWG_PN_2_3 n - TERMINALS APPLIED C1__DWG_PN_2_0 TE CRIMP SPECIFICATION MICRO TIMER 2 CONTACT WIRE STRIP LENGTH INSULATION DIAMETER RANGE 5 TE TERMINAL C1__DWG_PN_1_0 TERMINAL DATA: - 1.40-2.10 mm [.055-.083 IN] - - - CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.20+/-0.05 [.047+/-.002] 1.18+/-0.05 [.046+/-.002] 1.15+/-0.05 [.045+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 WIRE SIZE 4 5.6 5.8 6.1 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 1.00mm2 0.75mm2 0.50mm2 1 - 1.38+/-0.05 [.054+/-.002] 1.29+/-0.05 [.051+/-.002] 1.20+/-0.05 [.047+/-.002] - 5 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 2 2 2 2 1 1 1 1 1 1 1 - 1 2 - 2 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 - - - 1 - 1 1 1 1 1 - 1 1 1 A 1 1 - 1 1 1 - 1 2 - - 1 1 1 - 1 2 1 - 1 1 2 - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - 1 2 1 - TERMINAL LUBRICANT IS RECOMMENDED. 1 2 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 - 3 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - B 1 1 - 5.6 1 1 - 4.6 4 - - 3.8 1 4 - CRIMP HEIGHT 4 REFERENCE SETTING - 1 - CRIMP HEIGHT mm [INCH] - REF REF - 5 1 1 - C1__DWG_PN_1_4 1 - - (B)962900-3 (B)962900-4 1 1 - 5 1 1 - 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119791-5 2119943-1 2119740-1 2168078-1 5-18022-5 1338685-1 2168083-3 1803382-6 18023-9 2119652-1 1803602-1 1-1752356-8 2079383-5 2-2844962-8 2844992-2 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 454276-5 1-1333204-5 240641-9 2119757-4 238011-4 4-2119784-0 455888-9 1-456405-6 1 1 - 3 INSULATION DIAMETER RANGE - 1 1 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 09DEC2011 CHK 09DEC2011 APVD 09DEC2011 K.HUANG S.XI I.CRUZ - WEIGHT NAME SIZE - 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 1 5-18022-5 1 1338685-1 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 1-1752356-8 2 2079383-5 2 2-2844962-8 1 2844992-2 1 1-455888-0 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 454276-5 1 1-1333204-5 1 240641-9 .. 1 ITEM_6 1 2119757-4 1 238011-4 1 4-2119784-0 1 455888-9 1 1-456405-6 ITEM NO OCEAN SIDE FEED APPLICATOR A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 244 243 242 241 239 238 164 151 144 143 142 141 140 113 99 98 82 71 70 69 67 66 59 56 53 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 Harrisburg, PA 17105-3608 - 1 2079764 TE Connectivity APPLICATION SPEC - 1 2119082-8 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DRAWING NO - RESTRICTED TO 2151279 SCALE 1:2 SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 243 242 53 A 2 244 56 PNEUMATIC D 2 3 50 238 REF 8 7 2.4 34 59 82 C 0.5 1 SEE DETAIL A TERMINAL SUPPORT LOCATION 1 69 C 70 56 2 3 1 4 28 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 5 41 140 35.58 164 REF 0.05 66 2 DETAIL A REF 67 33 RAM SET-UP A 24 B 19 20 30 B 21 9 29 1 12 ITEM 30 LOCATED AT FRONT HOLES 241 CAM POSITIONS 30mm STROKE 13 REF REF 29 30mm STROKE 30mm STROKE 142 30 1 151 113 48 5 98 99 141 34 143 8 1 144 143 10 1 20 FEED TRACK POSITION GUIDE BY INSULATION BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 09DEC2011 CHK 09DEC2011 APVD 09DEC2011 K.HUANG S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN OCEAN SIDE FEED APPLICATOR - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 DRAWING NO - RESTRICTED TO 2151279 SCALE 1:2 SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F