2151672-1

7 8 THIS DRAWING IS UNPUBLISHED. C 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. COPYRIGHT 6 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER REVISION 2151672 -1 B 2151672 -2 FEED TYPE FINE CRIMP HEIGHT ADJUST B 2151672 -5 D DESCRIPTION FINE CRIMP HEIGHT ADJUST B MECHANICAL PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED SERVO LATCH PLATE SMART APPLICATOR FINE CRIMP HEIGHT ADJUST MECHANICAL FEED - 2151672 -6 B NON-CRIMP HEIGHT ADJUST 2151672 -7 B FINE CRIMP HEIGHT ADJUST NONE A PNEUMATIC FEED SERVO LATCH PLATE SERVO LATCH PLATE 7- 2151672 -7 APPLICATOR STYLE CONVERSION CHART CONVERT TO CRIMP TOOLING KIT - PNEUMATIC FEED 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 1338685-1 2119951-1 - 2161326-1 - 2119949-1 1338685-1 2119950-1 5-18022-5 8- 2151672 -5 8- 2151672 -4 5-18022-5 8- 2151672 -5 8- 2151672 -4 5-18022-5 1338685-1 - 5-18022-5 - - - - - - - - - 2119641-1 2119799-1 CRIMP WIRE INSUL SIZE - - 1901094-3 2119653-1 1901094-3 - 2119653-1 2119641-1 - - - - - - - - - - - - (QUANTITY 2) - - - 2063440-1 - - (QUANTITY 2) - 2119799-1 - 2168400-6 - - 2168400-6 - - - - - - - - - - - TYPE - F O 0.90 mm [.035] 1.00 mm [.039] APPLICATOR INSTRUCTIONS 408-10389 - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 1.10-1.50 mm [.043-.059 IN] C - CABLE PLUG CONTACT, 1.5CL WIRE TO BOARD CONNECTOR TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION - INSULATION DIAMETER RANGE - 0.80-1.00 mm [.031-.039 IN] 114-99005 - - - - - - - - TERMINALS APPLIED TE TERMINAL 2129408-1 TE TERMINAL C1__DWG_PN_1_0 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 - TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_1_1 - WIRE SIZE 24 AWG OR 0.20mm2 26 AWG OR 0.14mm2 28 AWG OR 0.09mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.61+/-0.03 [.024+/-.001] 0.56+/-0.03 [.022+/-.001] 0.51+/-0.03 [.020+/-.001] - CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 9.2 9.7 10.3 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. B - - - 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 -77 -7 A P LTR DESCRIPTION DATE DWN APVD 2063440-1 - APPLICATOR DATA REVISIONS DIST PART NUMBERS REQUIRED - LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 1 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 -6 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 -5 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 -2 1 22283-1 2-18032-5 1-22281-8 2168083-6 980371-4 356835-1 240792-1 2168083-1 1-690438-0 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-9 2079764-1 2119083-1 7-18023-7 -1 PART NO 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 - SPRING, COMPRESSION SCR, SET, FLT POINT M5 X 20.0 SPRING, COMPRESSION SCR, SKT HD CAP, RoHS, M5 X 65 SCR, SKT HD SHLDR 5.0 DIA X 6.0 LEVER, DRAG RELEASE DRAG, TERMINAL SCR, SKT HD CAP, RoHS, M3 X 8.0 FRONT STRIP GUIDE APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 DESCRIPTION 2 SIMP_22283-1 2 2-18032-5 1 SIMP_1-22281-8 1 2168083-6 1 980371-4 1 356835-1 1 240792-1 2 2168083-1 1 1-690438-0 1 2119957-2 1 8-21084-0_GATD 1 2119640-1 1 2079988_GATD 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-9 1 2079764 1 2119083 1 7-18023-7 - 279 278 277 276 275 274 273 271 270 260 252 250 249 248 247 246 245 244 243 242 241 1 1 1 ITEM NO 2 1 1 1 1 1 1 REF 1 1 1 1 1 1 1 1 2 1 3 1 1 4 1 1 1 - - 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -7 2 2 - - - - 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - 1 1 1 2 1 1 1 1 1 2 1 1 2168400-6 2119580-1 2063440-1 1-2079383-0 2119740-2 1901094-3 1-1976053-0 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 2119955-1 2-455888-3 5-547505-2 854769-4 2119956-1 2119791-5 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 21028-2 1338685-1 2168400-1 1-5018030-0 1-1901681-0 1752354-8 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-1 2119085-1 2119092-1 4-1752356-3 2079383-5 2161328-1 1320908-4 2-1901086-0 455888-3 1320928-2 2168083-2 1-18028-2 2119533-3 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-1 1633931-1 2119780-9 1-238011-6 2-1633962-4 2-1633713-8 -1 PART NO 1 2 1 1 1 1 1 1 REF REF REF REF - - - - - - REF REF 1 1 1 1 REF REF 1 1 1 1 1 1 1 1 1 1 1 1 - - 2 2 - 1 - 3 1 1 - - 1 1 - - 4 4 1 1 1 1 1 1 - - - - - - 1 1 - 1 1 1 - 1 - 1 1 1 1 1 - 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - - 1 1 1 1 1 1 - - 1 1 -6 -5 1 1 1 1 1 1 1 1 1 1 1 2 1 3 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 1 1 1 1 1 1 1 1 2 1 3 1 1 1 1 4 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE SCR, BHSC, RoHS (M3 X 6) TAG,IDENTIFICATION SPACER, FEEDER LOCATER BLOCK,TERMINAL PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF ASSY, LUBRICATOR, SIDE FEED SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM CRIMPER, WIRE PREMIUM 2 2168400-6 1 2119580-1 1 2063440-1 2 1-2079383-0 1 2119740-2 .. 1 1901094-3 1 1-1976053-0 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 2119955-1 1 2-455888-3 1 SIMP_5-547505-2 1 854769-4 1 2119956-1 1 2119791-5 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 21028-2 1 1338685-1 4 2168400-1 1 1-5018030-0 1 1-1901681-0 1 1752354-8 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 2119085 1 2119092-1 1 4-1752356-3 2 2079383-5 1 2161328 1 1320908-4 1 2-1901086-0 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533-3 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-1 1 1633931-1 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-9 1 1-238011-6 1 2-1633962-4 .. 1 ITEM_2 1 2-1633713-8 240 239 238 230 213 198 179 177 176 175 174 172 166 164 163 137 136 135 133 119 117 113 82 77 74 71 70 67 66 63 62 60 59 58 56 54 52 51 50 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO DESCRIPTION DWN CHK DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 3 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 6 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. LOC 1 REVISIONS DIST ALL RIGHTS RESERVED. P LTR DESCRIPTION DATE DWN APVD FEED TYPE 37 62 239 D 44 REF 40 59 38 56 39 250 249 246 260 44 252 245 35 244 63 245 REF 247 D 16.16 [.636] 50 REF HOLDDOWN SET-UP 243 166 242 238 163 8 82 59 34 REF 1 136 3 137 C REF 4 70 172 28 177 56 C 0.10 REF [.004] 5 TERMINAL SUPPORT LOCATION 41 176 174 240 133 52 135 175 198 179 51 230 50 164 66 67 33 A 24 30 B 117 REF 77 58 213 74 19 271 20 270 21 B 9 277 12 29 ITEM 30 LOCATED AT FRONT HOLES 241 13 CAM POSITIONS 48 29 REF 11 119 113 47 30 REF 279 278 273 274 275 276 46 32 34 54 8 60 54 10 FEED TRACK POSITION GUIDE BY TERMINAL BODY 248 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DWN CHK 49 AMP 4805 REV 31MAR2000 49 49 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 & 4 of 4) MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 3 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV 7 8 THIS DRAWING IS UNPUBLISHED. C 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. COPYRIGHT 6 PACIFIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER REVISION 2- 2151672 -1 DESCRIPTION B 2- 2151672 -2 D SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. FEED TYPE FINE CRIMP HEIGHT ADJUST B FINE CRIMP HEIGHT ADJUST MECHANICAL PNEUMATIC 2- 2151672 -5 B FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 2- 2151672 -7 B FINE CRIMP HEIGHT ADJUST NONE 7- 2151672 -7 A CRIMP TOOLING KIT - APPLICATOR STYLE CONVERSION CHART CONVERT TO PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED - PNEUMATIC FEED - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 5-18022-5 - 2119949-1 8- 2151672 -5 8- 2151672 -4 1338685-1 2119951-1 5-18022-5 - 2161326-1 8- 2151672 -5 - 2119949-1 8- 2151672 -4 1338685-1 2119950-1 5-18022-5 1338685-1 - 5-18022-5 - - - - 2119641-2 2119799-1 - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - - - - 2168400-6 (QUANTITY 2) 2119799-1 - - - 2168400-6 - - - - (QUANTITY 2) - - - - - 2063440-1 - - - - - - - TYPE 1.00 mm [.039] APPLICATOR INSTRUCTIONS 408-10389 - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 1.10-1.50 mm [.043-.059 IN] C - CABLE PLUG CONTACT, 1.5CL WIRE TO BOARD CONNECTOR TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION - INSULATION DIAMETER RANGE - 0.80-1.00 mm [.031-.039 IN] 114-99005 - - - - - - TERMINALS APPLIED TE TERMINAL 2129408-1 TE TERMINAL C1__DWG_PN_1_0 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_1_1 - WIRE SIZE 24 AWG OR 0.20mm2 26 AWG OR 0.14mm2 28 AWG OR 0.09mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.61+/-0.03 [.024+/-.001] 0.56+/-0.03 [.022+/-.001] 0.51+/-0.03 [.020+/-.001] - CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 9.2 9.7 10.3 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. - B - - - - - A P LTR DESCRIPTION DATE DWN APVD 2063440-1 F O 0.90 mm [.035] REVISIONS DIST PART NUMBERS REQUIRED - APPLICATOR DATA LOC 1 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 - 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 2 - 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 - 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 -77 -27 -25 -22 -21 22283-1 2-18032-5 1-22281-8 2168083-6 980371-4 356835-1 240792-1 2168083-1 1-690438-0 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-9 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 PART NO SPRING, COMPRESSION SCR, SET, FLT POINT M5 X 20.0 SPRING, COMPRESSION SCR, SKT HD CAP, RoHS, M5 X 65 SCR, SKT HD SHLDR 5.0 DIA X 6.0 LEVER, DRAG RELEASE DRAG, TERMINAL SCR, SKT HD CAP, RoHS, M3 X 8.0 FRONT STRIP GUIDE FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY DESCRIPTION 2 SIMP_22283-1 2 2-18032-5 1 SIMP_1-22281-8 1 2168083-6 1 980371-4 1 356835-1 1 240792-1 2 2168083-1 1 1-690438-0 1 2119782 1 2119640-1 1 2079988_GATD 1 1-22279-3_SIMP 1 2119082-9 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 - 279 278 277 276 275 274 273 271 270 251 250 249 246 244 243 242 241 240 239 1 1 1 - - 2 2 - 1 - 1 1 1 1 1 1 1 1 1 1 1 - - 1 1 REF 1 2 1 1 1 1 1 2 1 2063440-1 1-2079383-0 2119740-2 1901094-3 1-1976053-0 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 2119955-1 2-455888-3 5-547505-2 854769-4 2119956-1 2119791-5 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 21028-2 1338685-1 1-5018030-0 1-1901681-0 1752354-8 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-1 4-1752356-3 2079383-5 2161328-1 1320908-4 2-1901086-0 455888-3 1320928-2 2168083-2 1-18028-2 2119533-3 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-1 1633931-1 2119780-9 1-238011-6 2-1633962-4 2-1633713-8 2 1 1 1 1 1 1 REF REF REF - - 1 1 - - 1 1 1 1 4 4 - - 1 1 1 1 1 1 - - - - - REF - 1 1 1 - REF 1 1 1 1 1 1 1 1 1 1 1 1 1 - 2 2 1 1 3 3 - - 1 1 - - 1 1 1 1 1 1 - - - - 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - - 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 3 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 2 1 3 1 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PART NO -77 -27 -25 -22 -21 ITEM NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. AIR FEED MODULE SCR, BHSC, RoHS (M3 X 6) TAG,IDENTIFICATION SPACER, FEEDER LOCATER BLOCK,TERMINAL PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF ASSY, LUBRICATOR, SIDE FEED SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM CRIMPER, WIRE PREMIUM 1 2063440-1 2 1-2079383-0 1 2119740-2 .. 1 1901094-3 1 1-1976053-0 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 2119955-1 1 2-455888-3 1 SIMP_5-547505-2 1 854769-4 1 2119956-1 1 2119791-5 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 21028-2 1 1338685-1 1 1-5018030-0 1 1-1901681-0 1 1752354-8 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 4-1752356-3 2 2079383-5 1 2161328 1 1320908-4 1 2-1901086-0 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533-3 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-1 1 1633931-1 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-9 1 1-238011-6 1 2-1633962-4 .. 1 ITEM_2 1 2-1633713-8 238 230 213 198 179 177 176 175 174 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 113 82 77 74 71 70 67 66 63 62 59 58 56 52 51 50 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO DESCRIPTION DWN CHK DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 & 2 of 4) MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 1 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. COPYRIGHT 6 LOC 1 REVISIONS DIST ALL RIGHTS RESERVED. P FEED TYPE LTR DESCRIPTION DATE DWN APVD 251 62 40 145 38 D 239 D 16.16 [.636] 140 152 56 245 REF 246 39 59 44 REF 244 139 50 REF 243 HOLDDOWN SET-UP 250 166 249 242 63 238 8 34 REF REF 163 59 82 136 1 137 C 0.10 REF [.004] 3 172 177 56 176 4 TERMINAL SUPPORT LOCATION 70 C 28 5 41 174 52 240 133 135 175 198 51 179 230 164 66 50 77 67 33 A 24 30 19 117 REF 74 20 271 B 58 213 B 21 270 9 277 12 29 241 ITEM 30 LOCATED AT FRONT HOLES 13 CAM POSITIONS 30 29 113 REF REF 279 278 142 151 273 274 275 276 141 32 34 143 8 144 143 10 119 11 FEED TRACK POSITION GUIDE BY TERMINAL BODY 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 49 49 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 CHK DIMENSIONS: & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 DWN TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 1 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV