2151729-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE J FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151729-1 J MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151729-2 J 7- 2151729 -7 A J 3 2 LOC 2151729 -1 2151729 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD G ECR-20-005860 23APR2020 FJ RK H ECR-20-017679 14DEC2020 JWC TE H1 ECR-21-006079 07JUN2021 LJ YY J ECR-21-006568 28JUN2021 JWC RK PNEUMATIC CRIMP TOOLING KIT - D D - CRIMP WIRE INSUL - APPLICATOR DATA SIZE - TYPE F O 2.54 mm [.100] 4.57 mm [.180] APPLICATOR INSTRUCTIONS 408-35042 - 3 - - - TE TERMINAL TERMINAL DATA: 2.8mm BLADE SEALED TERMINAL NAME: WIRE STRIP LENGTH 4.80-5.60 mm [.189-.220 IN] C TERMINAL APPLICATION SPECIFICATION 114-13013 - TERMINALS APPLIED TE TERMINAL 1-1326031-0 n 6 C1__DWG_PN_1_1 TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - - - - - - - - 7 TE TERMINAL 1-1326032-1 C1__DWG_PN_1_0 - 7 C1__DWG_PN_2_0 C1__DWG_PN_2_1 FORD SEAL 97BG-10C930-GA TE SEAL 286819-1 C1__DWG_PN_3_0 C1__DWG_PN_3_1 C1__DWG_PN_4_0 - CABLE DIMENSION - C1__DWG_PN_4_1 - WIRE SIZE 2.50mm2 14 AWG 1.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.80+/-0.05 [.071+/-.002] 1.69+/-0.05 [.067+/-.002] 1.55+/-0.05 [.061+/-.002] CRIMP HEIGHT REFERENCE SETTING 7.5 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 8.5 10.1 - 5 4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - 1 2 B 3 4 5 6 7 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. WHEN CHANGING FROM ONE TERMINAL TO ANOTHER ADJUSTMENT OF THE FEED MAY BE REQUIRED. TERMINAL LUBRICANT IS RECOMMENDED. 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 - 1 - 1 - - 1 1 - 1 1 1 1 A - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 2 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL - 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC SPRING, COMPRESSION WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SCR, BHSC, RoHS (M4 X 8) EXTENSION PLATE DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 10 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 24JUL2012 CHK 24JUL2012 APVD 24JUL2012 C.CHEN S.XI I.CRUZ - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 SIMP_1-22281-8 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 2-690438-8 2 2168083-1 1 2168083-6 1 455888-4 2 2079383-4 1 1803096-1 1 1803607_3 1 2119740-1 2 2168078-1 2 2-18032-5 1 2168083-2 1 5-18022-5 1 985575-3 1 1338683-8 4 2168083-3 2 1-2168083-0 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 2-1752356-0 2 2079383-5 2 1-2844962-7 1 2-2844938-6 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-1 1 1320928-4 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1633922-7 .. 1 ITEM_6 1 2119781-1 1 2-238011-1 1 6-2119784-0 1 1-455888-6 1 456407-4 248 244 243 242 241 239 238 164 121 119 113 99 98 96 95 93 82 79 78 71 67 66 61 60 59 57 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119082-9 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH PART NO 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. mm -1 1 -77 -72 -71 -2 DIMENSIONS: 1 1 1 1 2 1 1 2 1 - 1 1 2 1 - 1 1 1 1 - 1 1 1 2 - 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 2 1 1 2 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 1 2 1 1 1 1 2 1 2 1 1 2 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 - REF REF 1 1 1 1 REF 1 1 - - REF 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-22281-8 1-18028-2 2119955-1 2844908-1 2844907-1 2-690438-8 2168083-1 2168083-6 455888-4 2079383-4 1803096-1 1803607-3 2119740-1 2168078-1 2-18032-5 2168083-2 5-18022-5 985575-3 1338683-8 2168083-3 1-2168083-0 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 2-1752356-0 2079383-5 1-2844962-7 2-2844938-6 455888-3 22283-1 356835-1 240792-1 1320928-4 980371-4 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1633922-7 2119781-1 2-238011-1 6-2119784-0 1-455888-6 456407-4 - Ocean Side Feed Applicator - DRAWING NO 2151729 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV J C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE MECHANICAL A D 239 5 REF D 59 56 1.4 REF 44 PNEUMATIC 2 57 REF SHEAR DEPRESSOR DETAIL 244 243 A 238 242 53 2 3 50 8 59 C 82 1 3.5 REF 0.5 34 REF 1 C 2 SEE DETAIL A 3 1 56 4 TERMINAL SUPPORT LOCATION 28 5 41 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 44 REF 43.90 164 2 0.05 66 DETAIL A 67 33 57 RAM SET-UP 5 24 A 30 B 19 79 B 20 78 21 95 96 9 29 12 25 241 CAM POSITIONS 13 30 REF 29 REF 1 119 30mm STROKE 113 47 ITEM 30 LOCATED AT REAR HOLES 11 30mm STROKE 30mm STROKE 1 7 27 61 26 23 121 93 46 98 99 34 54 8 1 60 54 10 1 248 48 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 24JUL2012 CHK 24JUL2012 APVD 24JUL2012 C.CHEN S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151729 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV J 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151729 -1 J FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151729 -7 A CRIMP TOOLING KIT - J 3 2 LOC PART NUMBER 2- 2151729 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE - TYPE 4.57 mm [.180] APPLICATOR INSTRUCTIONS 408-35042 - 2.8mm BLADE SEALED WIRE STRIP LENGTH 1 4.80-5.60 mm [.189-.220 IN] C TERMINAL APPLICATION SPECIFICATION 1-1326031-0 114-13013 - TERMINALS APPLIED TE TERMINAL n 6 - - - C1__DWG_PN_2_0 C1__DWG_PN_2_1 FORD SEAL 97BG-10C930-GA - 2.50mm2 14 AWG 1.50mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 CRIMP HEIGHT REFERENCE SETTING 1.80+/-0.05 [.071+/-.002] W1__DWG_CRIMP_HT_1 1.69+/-0.05 [.067+/-.002] W1__DWG_CRIMP_HT_2 1.55+/-0.05 [.061+/-.002] W1__DWG_CRIMP_HT_3 7.5 8.5 10.1 - 4 5 6 7 ENTRY LEVEL APPLICATOR A ITEM ITEM DESCRIPTION 2151729-1 1 WIRE CRIMPER SUBSTITUTE PART NUMBER 1803552-4 9-2151729-1 2-2151729-1 46 BASIC SUB -ASSEMBLY 1803940-9 8-2151729-2 9-2151729-2 2151729-2 2-2151729-2 3 141 INSULATION CRIMPER BASIC SUB -ASSEMBLY LUBRICATOR 1 1 1 1 1 1 1 1 1 - - 1 1 1 1 1 - 1 1 1 1 1 1-1803940-0 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DELETE DIMENSIONS: Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 24JUL2012 CHK 24JUL2012 APVD 24JUL2012 C.CHEN S.XI I.CRUZ - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 SIMP_1-22281-8 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 2-690438-8 2 2168083-1 1 2168083-6 1 455888-4 2 2079383-4 1 1803096-1 1 1803607_3 1 2119740-1 2 2168078-1 2 2-18032-5 1 5-18022-5 1 985575-3 1 1338683-8 2 1-2168083-0 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 2-1752356-0 2 2079383-5 2 1-2844962-7 1 2-2844938-6 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-1 1 1320928-4 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1633922-7 .. 1 ITEM_6 1 2119781-1 1 2-238011-1 1 6-2119784-0 1 1-455888-6 1 456407-4 244 243 242 241 239 238 164 151 144 143 142 141 140 121 119 113 99 98 96 95 93 82 79 78 71 67 66 61 59 57 56 53 50 49 48 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2079764_APP TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC SPRING, COMPRESSION WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SCR, BHSC, RoHS (M4 X 8) EXTENSION PLATE DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 10 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 1 1 1 1 1 1 - 1 1 1 - 6-1803604-0 1 1 - 1 1 1 - 1 1 1 - SAME AS 1 1 - PART NUMBER 8-2151729-1 1 1 - ITEM SUBSTITUTION LIST 2 1 - 1 1 2 - 1 1 1 - - 2 1 - 1 2 2 - 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 2 - TERMINAL LUBRICANT IS RECOMMENDED. 1 1 - - 1 1 - 1 2 - - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - WHEN CHANGING FROM ONE TERMINAL TO ANOTHER ADJUSTMENT OF THE FEED MAY BE REQUIRED. 2 1 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 2 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 - 3 2 1 - B 2 2 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 2 - 2 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 2 1 - 5 1 2 - W1__FA_SETTING_3 1 1 - W1__FA_SETTING_2 2 1 - W1__FA_SETTING_1 1 2 - 4 1 1 - CRIMP HEIGHT mm [INCH] 1 1 - WIRE SIZE 1 1 - CABLE DIMENSION 1 1 - C1__DWG_PN_4_1 1 1 - 286819-1 C1__DWG_PN_3_1 1 1 - C1__DWG_PN_4_0 1 1 - TE SEAL C1__DWG_PN_3_0 1 1 - 7 4 - - 1-1326032-1 C1__DWG_PN_1_1 - 1 4 - 7 TE TERMINAL C1__DWG_PN_1_0 - - 1 - INSULATION DIAMETER RANGE - REF REF - TERMINAL NAME: 1 1 - TE CRIMP SPECIFICATION 1 - - TE TERMINAL 1 1 - TERMINAL DATA: 1 1 - 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-22281-8 1-18028-2 2119955-1 2844908-1 2844907-1 2-690438-8 2168083-1 2168083-6 455888-4 2079383-4 1803096-1 1803607-3 2119740-1 2168078-1 2-18032-5 5-18022-5 985575-3 1338683-8 1-2168083-0 1803382-6 18023-9 2119652-1 1803602-1 2-1752356-0 2079383-5 1-2844962-7 2-2844938-6 455888-3 22283-1 356835-1 240792-1 1320928-4 980371-4 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1633922-7 2119781-1 2-238011-1 6-2119784-0 1-455888-6 456407-4 1 1 - 3 F O 2.54 mm [.100] 1 Ocean Side Feed Applicator - DRAWING NO 2151729 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV J C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 2 57 243 242 A D 1.4 REF 244 56 PNEUMATIC SHEAR DEPRESSOR DETAIL 2 3 3.5 53 238 REF 8 50 0.5 REF 34 59 82 C REF 5 SEE DETAIL A 1 REF TERMINAL SUPPORT LOCATION 1 C 2 56 3 1 4 28 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 5 41 140 REF 34.87 0.05 66 DETAIL A 164 2 67 33 57 5 RAM SET-UP 24 A 30 79 B 19 20 78 CAM POSITIONS 30mm STROKE 9 21 95 12 96 241 29 13 1 ITEM 30 LOCATED AT REAR HOLES 1 30 25 REF REF 29 30mm STROKE 30mm STROKE 142 B 151 113 48 7 27 61 26 23 121 93 141 98 99 34 143 8 1 144 143 10 1 119 FEED TRACK POSITION GUIDE BY INSULATION BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 24JUL2012 CHK 24JUL2012 APVD 24JUL2012 C.CHEN S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151729 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV J