2151943-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2151943 -1 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151943-1 B MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151943-2 B 7- 2151943 -7 A B 3 2 LOC PART NUMBER 2151943 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST CRIMP TOOLING KIT - 3 WIRE INSUL - - - TYPE - F O 1.40 mm [.055] 1.68 mm [.066] APPLICATOR INSTRUCTIONS 408-35042 - DELPHI TERMINAL TERMINAL DATA: TAXI TERM F OCS 1.2 TERMINAL NAME: WIRE STRIP LENGTH n 3.78-3.79 mm [.149-.149 IN] C TERMINAL APPLICATION SPECIFICATION 13627884 Rev - - DELPHI CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 1.47-1.90 mm [.058-.075 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 2113340-1 DELPHI TERMINAL 13627884 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 - DELPHI TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 0.50mm2 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 0.90+/-0.05 [.035+/-.002] 0.85+/-0.05 [.033+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 8.3 8.8 - 4 W1__FA_SETTING_1 W1__FA_SETTING_2 - 6 - 7 - 1 B 2 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 6 CABLE TYPE CODE LEGEND 1005, SAE. INSULATION DIAMETER 1.60-1.88. 7 CABLE TYPE CODE LEGEND 1047, SAE. INSULATION DIAMETER 1.40-1.75. - 1 - 1 - 1 1 - 1 - 1 1 1 1 A - 1 - 1 1 DESCRIPTION DATE DWN APVD A RELEASED 23MAY2013 RW TE B ECR-18-008463 02JUN2018 TB TE - 1 1 - 1 1 1 - 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - 1 2 PART NO 1 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH -1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: 1 1 1 1 2 1 1 2 1 - 1 1 2 1 - 1 1 1 1 - 1 1 1 1 - 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 2 1 1 2 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 - 1 - 1 - REF REF - 1 - 2 REF 1 1 1 - REF 1 - - 2 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 2119640-1 2079988-1 2119641-1 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2063440-1 21045-3 994970-2 240638-1 3-23627-7 2119799-1 1-22281-8 1-18028-2 2844908-1 2844907-1 1-690438-0 2168083-1 2168083-6 455888-5 22278-8 854769-4 1803607-1 2119740-1 2168078-1 2-18032-5 2168083-2 5-18022-5 21028-2 1338685-1 2168083-3 2-2168083-5 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1752356-6 2079383-5 2-2844962-4 2844938-1 455888-3 22283-1 356835-1 240792-5 1320928-2 980371-4 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-4 1-1633917-7 240641-3 1-2119780-1 1-238011-7 1-1633966-9 455888-7 1-456402-4 - -77 -72 -71 -2 AMP 4805 REV 31MAR2000 LTR - D SIZE P PNEUMATIC - CRIMP 66 PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT APPLICATOR DATA REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 - PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE RING, RETAIN, EXTERN, 3/16 CRESCENT COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF SPRING, COMPRESSION WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 14 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 22APR2013 CHK 29APR2013 APVD 29APR2013 R.O.WILSON K.J.STAKEM T.L.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119082-8 1 2079764 1 2119083 1 7-18023-7 1 2119580-1 1 2063440-1 2 21045-3 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 SIMP_1-22281-8 1 1-18028-2 1 2844908 1 2844907 1 1-690438-0 2 2168083-1 1 2168083-6 1 455888-5 1 SIMP_22278-8 1 854769-4 1 1803607-1 1 2119740-1 2 2168078-1 2 2-18032-5 1 2168083-2 1 5-18022-5 1 21028-2 1 1338685-1 4 2168083-3 2 2-2168083-5 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1752356-6 2 2079383-5 2 2-2844962-4 1 2844938-1 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-5 1 1320928-2 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-4 1 1-1633917-7 1 240641-3 .. 1 ITEM_6 1 1-2119780-1 1 1-238011-7 1 1-1633966-9 1 455888-7 1 1-456402-4 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119641-1 250 249 248 244 243 242 241 239 238 172 164 163 137 136 121 119 99 98 96 95 93 82 77 74 71 67 66 61 60 59 58 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079988_GATD DESCRIPTION PRODUCT SPEC - 1 2119640-1 Ocean Side Feed Applicator - DRAWING NO 2151943 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV B D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 56 44 PNEUMATIC 250 2 2 244 249 243 A 53 238 242 50 163 3 8 7 59 82 1 136 REF 1.0 0.5 34 REF 1 137 C 2 C 2 172 3 1 56 4 TERMINAL SUPPORT LOCATION 28 5 41 44 44.61 REF 0.05 66 2 164 77 33 A 24 B 67 RAM SET-UP 58 74 19 30 20 95 21 B 9 96 1 ITEM 30 LOCATED AT FRONT HOLES 12 29 CAM POSITIONS 47 13 25 30 REF 29 REF 1 11 30mm STROKE 30mm STROKE 30mm STROKE 241 119 27 61 26 23 121 93 46 98 99 34 54 8 1 60 54 10 1 248 48 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 22APR2013 CHK 29APR2013 APVD 29APR2013 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151943 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151943 -1 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151943 -7 A CRIMP TOOLING KIT - B 3 2 LOC PART NUMBER 2- 2151943 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST 1 - 1.68 mm [.066] APPLICATOR INSTRUCTIONS 408-35042 - - 1 - WIRE STRIP LENGTH n 3.78-3.79 mm [.149-.149 IN] C TERMINAL APPLICATION SPECIFICATION 13627884 Rev - - - - - TE TERMINAL 2113340-1 13627884 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 - 0.50mm2 0.35mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 0.90+/-0.05 [.035+/-.002] 0.85+/-0.05 [.033+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 8.3 8.8 2 REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 6 CABLE TYPE CODE LEGEND 1005, SAE. INSULATION DIAMETER 1.60-1.88. 7 CABLE TYPE CODE LEGEND 1047, SAE. INSULATION DIAMETER 1.40-1.75. 1 1 1 1 1 2 2 2 2 1 - 1 1 - 1 2 - 2 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 - - - 1 - 1 1 1 1 - A 2 - - 1 1 1 - 1 2 1 - 1 1 2 - 1 1 1 - 1 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - B 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 7 2 1 - W1__FA_SETTING_2 1 2 - 6 1 1 - W1__FA_SETTING_1 1 1 - 4 1 1 - CRIMP HEIGHT REFERENCE SETTING 1 1 - CRIMP HEIGHT mm [INCH] - 1 - WIRE SIZE - 1 - DELPHI TERMINAL 1 1 - C1__DWG_PN_2_1 1 1 - C1__DWG_PN_4_0 1 1 - DELPHI TERMINAL C1__DWG_PN_1_0 4 - - TERMINALS APPLIED 1 4 - 1.47-1.90 mm [.058-.075 IN] - 1 - INSULATION DIAMETER RANGE - 1 - TAXI TERM F OCS 1.2 - REF REF - TERMINAL NAME: - 2 - DELPHI CRIMP SPECIFICATION 1 1 - DELPHI TERMINAL 1 - - TERMINAL DATA: 1 1 - F O 1.40 mm [.055] 1 1 - TYPE 1 1 - 3 - 1 - WIRE INSUL 1 1 1 1 1 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE RING, RETAIN, EXTERN, 3/16 CRESCENT COUNTER, MAGNETIC SPRING, FEED FINGER FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF SPRING, COMPRESSION WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 14 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 AMP 4805 REV 31MAR2000 LTR 2119640-1 2079988-1 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2063440-1 21045-3 994970-2 240638-1 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 3-23627-7 2119799-1 1-22281-8 1-18028-2 2844908-1 2844907-1 1-690438-0 2168083-1 2168083-6 455888-5 22278-8 854769-4 1803607-1 2119740-1 2168078-1 2-18032-5 5-18022-5 21028-2 1338685-1 2-2168083-5 1803382-6 18023-9 2119652-1 1803602-1 1752356-6 2079383-5 2-2844962-4 2844938-1 455888-3 22283-1 356835-1 240792-5 1320928-2 980371-4 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-4 1-1633917-7 240641-3 1-2119780-1 1-238011-7 1-1633966-9 455888-7 1-456402-4 - 1 - SIZE P - PNEUMATIC D CRIMP 66 - - APPLICATOR DATA REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 DWN 22APR2013 CHK 29APR2013 APVD 29APR2013 R.O.WILSON K.J.STAKEM T.L.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2079764 1 2119083 1 7-18023-7 1 2119580-1 1 2063440-1 2 21045-3 1 COUNTER_994970 1 240638 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 3-23627-7 1 2119799 1 SIMP_1-22281-8 1 1-18028-2 1 2844908 1 2844907 1 1-690438-0 2 2168083-1 1 2168083-6 1 455888-5 1 SIMP_22278-8 1 854769-4 1 1803607-1 1 2119740-1 2 2168078-1 2 2-18032-5 1 5-18022-5 1 21028-2 1 1338685-1 2 2-2168083-5 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 1752356-6 2 2079383-5 2 2-2844962-4 1 2844938-1 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-5 1 1320928-2 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-4 1 1-1633917-7 1 240641-3 .. 1 ITEM_6 1 1-2119780-1 1 1-238011-7 1 1-1633966-9 1 455888-7 1 1-456402-4 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119082-8 250 249 244 243 242 241 239 238 172 164 163 151 144 143 142 141 140 137 136 121 119 99 98 96 95 93 82 77 74 71 67 66 61 59 58 56 53 50 49 48 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079988_GATD DESCRIPTION PRODUCT SPEC - 1 2119640-1 Ocean Side Feed Applicator - DRAWING NO 2151943 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 243 250 242 2 249 2 3 53 1.0 238 A 2 244 56 PNEUMATIC D 50 REF 8 163 0.5 7 34 59 REF 136 82 137 C 1 172 TERMINAL SUPPORT LOCATION 1 C 2 56 3 1 4 28 5 41 140 REF 35.58 0.05 66 33 67 2 164 77 RAM SET-UP A 24 B 58 19 74 20 30 9 21 95 30mm STROKE 241 13 29 ITEM 30 LOCATED AT FRONT HOLES 1 30 25 REF REF 29 30mm STROKE 30mm STROKE 142 1 12 96 CAM POSITIONS B 151 27 48 61 26 23 121 93 141 98 99 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 22APR2013 CHK 29APR2013 APVD 29APR2013 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151943 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B