2170722-1

4 RELEASED FOR PUBLICATION THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 2 3 1 20 REVISIONS ALL RIGHTS RESERVED. BY - P LTR 1 D 2170722-2 AS SHOWN SCALE 1:1 2170722-1AS SHOWN SCALE 1:1 C REFERENCE APPLICATION SPECIFICATION 114-***** FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS 3 DATUM AND BASIC DIMENSION ESTABLISHED BY CUSTOMER 4 DATE CODE (YYWWD) MARKED APPROXIMATELY AS SHOWN. 5. MATES WITH QSFP28 MSA COMPATIBLE TRANSCEIVER. 6. MINIMUM PC BOARD THICKNESS: SINGLE SIDED: 1.57 MIN DOUBLE SIDED: 3.00 MIN B -A- DWN APVD JY 17JAN2014 2 REF - D C IS TOP SURFACE OF THE HOST BOARD. THESE HOLES ARE OPTIONAL WHEN THE REAR PINS ARE REMOVED. 57.15 0.10 6X 8.90 SCALE PRELIMINARY COMPONENTS CAGE ASSEMBLY: NICKEL-SILVER ALLOY RETENTION PLATE: STAINLESS STEEL EMI SPRING: COPPER ALLOY/NICKEL PLATE GASKET: PLATED FILLED SILICONE WITH 94 V_0 8 6X 18.75 DATE 1. 7. DATUM 114.57 DESCRIPTION 0.10 9.72 -T- REF C SEE DETAIL 2:1 REF 2.05 TYP B 47.50 18.50 REAR PINS OPTIONAL 4X 19.00 WITHOUT 7.88 2:1 THIS DRAWING IS A CONTROLLED DOCUMENT. A DIMENSIONS: mm 3.0 MAX PRELIMINARY PART- NOT RELEASED FOR PRODUCTION 1471-9 (3/13) DETAIL C SCALE 6:1 MATERIAL SEE NOTES - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.25 0.2 - SEE NOTES - DWN 2170722-2 WITH WITHOUT REAR PIN OPTIONAL JASON YANG JAN162014 CHK - APVD - - - NAME - WEIGHT SIZE - Customer Drawing 2170722-1 PART NUMBER TE Connectivity APPLICATION SPEC - 2170722-4 HEAT SINK OPEN OPTIONAL PRODUCT SPEC - WITH WITHOUT WITH V-V 2170722-5 WITHOUT 5X 19.00 SECTION SCALE WITH A CAGE ASSEMLBY, 1X6 QSFP28 THRU BEZEL, GASKET - CAGE CODE A2 00779 DRAWING NO 2170722 SCALE 1:1 SHEET RESTRICTED TO 1 OF - 5 REV 1 4 RELEASED FOR PUBLICATION THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 BY - 2 3 1 20 REVISIONS ALL RIGHTS RESERVED. P LTR DESCRIPTION - D R 0.30 MAX TYP SEE SHEET 1 DWN APVD - - - D 119.75 MIN PITCH ( 1.60 ) -T- BEZEL 43.00 10.15 DATE 0.30 0.10 115.00 C 0.10 37.00 0.15 0.10 (BOTTOM OF CUT-OUT IN BEZEL TO TOP PCB) MAX GUIDE PINS PER SPEC C SINGLE SIDE MOUNTING SCALE 2:1 R 0.30 MAX TYP 119.75 MIN PITCH -T0.15 0.10 (BOTTOM OF CUT-OUT IN BEZEL TO TOP PCB) B B 10.15 0.10 0.15 0.10 (BOTTOM OF CUT-OUT IN BEZEL TO TOP PCB) 115.00 0.10 BELLY TO BELLY MOUNTING SCALE 2:1 THIS DRAWING IS A CONTROLLED DOCUMENT. A DIMENSIONS: mm PRELIMINARY PART- NOT RELEASED FOR PRODUCTION MATERIAL SEE NOTES - 1471-9 (3/13) TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.25 0.2 - SEE NOTES - DWN JASON YANG JAN162014 CHK - APVD - - - TE Connectivity NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - Customer Drawing A CAGE ASSEMLBY, 1X6 QSFP28 THRU BEZEL, GASKET - CAGE CODE A2 00779 DRAWING NO 2170722 SCALE 1:1 SHEET RESTRICTED TO 2 OF - 5 REV 1 4 RELEASED FOR PUBLICATION THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 1 20 REVISIONS ALL RIGHTS RESERVED. BY - 20 2 3 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - -Y- D 3 D 8 BSC 1.10 TYP 8 16.28 4X 8 19.00 110.78 6X ( n 1.05 ) REAR PIN HOLES 8 THIS AREA DENOTES COMPONENTS KEEP-OUT (TRACES ALLOWED) CROSS HATCHED AREA DENOTES WHEN SURFACE TRACES ARE PERMITTED A SEE DETAIL 8 12.79 C 7.60 3.10 -L- 3X MIN C -K- 9.00 9.00 3 BSC MAX 13.49 3.10 7.60 3X 12.49 37.00 MAX 41X 1.05 0.05 COMPLIANT PIN HOLE 2 B B -X- 19.00 38.00 57.00 76.00 HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) 95.00 114.00 116.00 RECOMMENDED PCB LAYOUT SINGLE TYPE PCB TOLERANCE: # 0.05 SCALE 3:1 A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL SEE NOTES - 1471-9 (3/13) TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.25 0.2 - SEE NOTES - DWN JASON YANG JAN162014 CHK - APVD - - - TE Connectivity NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - Customer Drawing A CAGE ASSEMLBY, 1X6 QSFP28 THRU BEZEL, GASKET - CAGE CODE A2 00779 DRAWING NO 2170722 SCALE 1:1 SHEET RESTRICTED TO 3 OF - 5 REV 1 4 RELEASED FOR PUBLICATION THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 1 20 REVISIONS ALL RIGHTS RESERVED. BY - 20 2 3 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - -YD 3 110.78 BSC 1.10 CROSS HATCHED AREA DENOTES WHEN SURFACE TRACES ARE PERMITTED 110.78 16.28 8 8 THIS AREA DENOTES COMPONENTS KEEP-OUT (TRACES ALLOWED) 8 4X D 8 19.00 4X 8 19.00 8 16.28 B SEE DETAIL 12X ( n 1.05 ) REAR PIN HOLES 8 8 C 12.79 7.60 -L- BSC MAX 13.49 MIN 3.10 C -K- 3.10 7x 3 12.49 4.50 82X n 1.05 0.05 COMPLIANT PIN HOLE 2 37.00 MAX B B -X19.00 38.00 57.00 76.00 95.00 HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) 114.00 116.00 RECOMMENDED PCB LAYOUT BELLY TO BELLY TYPE PCB TOLERANCE: # 0.05 SCALE 3:1 A PRELIMINARY PART- NOT RELEASED FOR PRODUCTION 1471-9 (3/13) THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL SEE NOTES - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.25 0.2 - SEE NOTES - DWN JASON YANG JAN162014 CHK - APVD - - - TE Connectivity NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - Customer Drawing A CAGE ASSEMLBY, 1X6 QSFP28 THRU BEZEL, GASKET - CAGE CODE A2 00779 DRAWING NO 2170722 SCALE 1:1 SHEET RESTRICTED TO 4 OF - 5 REV 1 4 RELEASED FOR PUBLICATION THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 2 3 1 20 REVISIONS ALL RIGHTS RESERVED. BY - P LTR - 1.50 D TYP 1.50 SEE SHEET 1 DWN APVD - - - D TYP MAX -L1.55 DATE 2X 4.62 1.69 C DESCRIPTION 1.50 -K3.10 0.05 1.55 -L- 2X 4.62 1.50 C TYP MAX 0.05 -K- 15.02 16.80 TYP 1.20 DETAIL A SCALE 6:1 1.69 MAX -L- -K- B 3.10 1.55 0.05 1.55 -L- 15.02 B MAX 0.05 -K- 16.80 1.20 B DETAIL SCALE 6:1 THIS DRAWING IS A CONTROLLED DOCUMENT. A DIMENSIONS: mm MATERIAL 1471-9 (3/13) PRELIMINARY PART- NOT RELEASED FOR PRODUCTION SEE NOTES - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.25 0.2 - SEE NOTES - DWN JASON YANG JAN162014 CHK - APVD - - - TE Connectivity NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - Customer Drawing A CAGE ASSEMLBY, 1X6 QSFP28 THRU BEZEL, GASKET - CAGE CODE A2 00779 DRAWING NO 2170722 SCALE 1:1 SHEET RESTRICTED TO 5 OF - 5 REV 1