218M628-19B

ANTI-ROTATION SCREW 7 CODE 18 - HEAT SHRINK BOOT BACKSHELL 218M632A19B SERIES DASH NUMBER (TABLE 1) MANUFACTURER CODE SEE TABLE 2 MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATION, SEE CH00-0250-004. 3. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-218M612-19B). 4. BACKSHELL MATES TO MIL-DTL-5015, CLASS A, E & R, MS3100, MS3101 &MS3106. RESILIENT INSERT, SOLDER TYPE AND BENDIX 10-214, CANNON CA-RX COMMERCIAL CRIMP TYPE (LESS ENDBELL). 5. ALL THREAD SIZES FOR ORDER APPLY. 6. ADDITIONAL PIECE(S) SUPPLIED WHEN CONNECTOR MFR IS UNKNOWN (D IN TABLE 2) 7. ANTI-ROTATIONAL SET SCREW, THREE #4-40 THREADED HOLES 120° APART, SINGLE MATING SET SCREW SUPPLIED. If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 26/05/2015 CHECKED 26/05/2015 APPROVED K.SHEPPARD 27/04/2015 APPROVED H.SMITH 02/09/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECN AD93111 J REVISED PER ECO-15-012672 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE APPROVED 02/09/2015 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 TITLE: HEAT SHRINK BOOT BACKSHELL ASSY USED ON: MIL-DTL-5015D TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 218M6XX J 1 A-A A SILICONE O-RING ØY ØZ XXXX ØB A THREAD X 27,00 A PART MARK HERE TABLE 1 10 11 12 14 16 18 20 22 24 28 32 36 40 44 48 TABLE 2 MFR CODE A B C D R - 8S 8S 8S 8S 10S 10SL 10SL 10SL 12 & 12S 12 & 12S 12 & 12S 14 & 14S 16 & 16S 18 20 20 20 22 24 28 32 32 32 36 36 36 36 36 40 40 40 44 48 48 48 MFR CODE TABLE 3 B C A, R D 6 C A, B, R D 6 B, C A, R D 6 A, B, C R D 6 B, C A, R D 6 B R C A D 6 B A, C, R D 6 C A, R D 6 A THREAD ØB MAX ØZ ØY MAX X +0,20/-0,00 3/8-32 UNEF 7/16-28 UNEF 7/16-27 UNS 5 1/2-28 UNEF 9/16-24 UNEF 5/8-24 UNEF 5 5/8-24 UNEF 11/16-24 UNEF 5 3/4-20UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/8-24 UNS 5 1 1/4-18 UNEF 1 3/8-18 UNEF 1 5/8-18 UNEF 1 7/8-16 UN 1 29/32-18 UN 5 2 1/16-16 UNS 2 1/16-20 UNS 2 1/8-16 UN 2 1/8-18 UNS 5 2 5/16-16 UN 2 3/8-16UN 5 2 5/8-16 UN 2 13/16-18 UNS 2 7/8-16 UN 5 18,5 18,0 18,5 18,5 19,8 21,6 23,0 23,0 23,0 24,9 24,9 27,7 31,1 34,4 37,6 37,6 37,6 40,6 43,6 48,6 54,9 54,9 54,9 64,6 64,6 64,6 64,6 64,6 70,6 70,6 69,3 82,0 82,0 82,0 82,0 6,2 8,0 8,0 8,0 9,5 11,2 12,7 11,2 12,7 14,3 12,7 16,0 19,0 20,7 25,4 25,4 25,4 28,5 31,8 35,0 41,5 41,3 41,5 47,6 47,6 48,0 47,6 48,0 54,0 54,0 54,0 60,3 66,7 66,7 66,7 13,0 13,0 13,0 13,0 15,0 16,0 19,0 19,0 19,0 19,0 19,0 21,0 24,0 26,0 34,0 34,0 34,0 36,0 40,5 43,0 48,0 48,0 48,0 54,5 54,5 54,5 54,5 54,5 60,5 60,5 60,5 67,6 74,0 74,0 74,0 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,12 1,75 1,75 1,75 1,75 1,75 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 2,20 28,40 MAX SILICONE O-RING CONNECTOR MANUFACTURER (MS 3100, MS 3101 & MS 3106) AMPHENOL - CLASS A BENDIX - CLASS A, E & R CANNON - CLASS A, E & R MFR UNKNOWN, CLASS A, E & R AMPHENOL - CLASS R MFR CODE NOT REQUIRED A THREAD 08 SHELL SIZE ØB ORDER NUMBER ADDITIONAL PIECE(S) SUPPLIED WHEN CONNECTOR MANUFACTURER IS UNKNOWN ("D" IN TABLE 3) If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 26/05/2015 CHECKED 26/05/2015 APPROVED K.SHEPPARD 27/04/2015 APPROVED H.SMITH 02/09/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECN AD93111 J REVISED PER ECO-15-012672 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE APPROVED 02/09/2015 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 TITLE: HEAT SHRINK BOOT BACKSHELL ASSY USED ON: MIL-DTL-5015D TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 218M6XX J 2