2198224-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY - 6 5 4 3 2 20 LOC ALL RIGHTS RESERVED. 1 PIN TYPE HEAT SINK GP MATERIAL: CAGE ASSEMBLY: 0.25mm THICK NICKEL SILVER ALLOY GASKET RETENTION PLATE: STAINLESS STEEL EMI GASKET: PLATED FILLED SILICONE HEATHSINK CLIP: STAINLESS STEEL HEATSINK: ALUMINUM 2 FINISH: HEATSINK: ELECTROLESS NICKEL HEATSINK CLIP: PASSIVATE 3 DATUM AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 4 PADS AND VIAS CHASSIS GROUND. 10 2198224-1,2,3,4 FINISHED ASSEMBLY 13 7 HOLE PATTERN REPEATS FOR EACH PORT, SPACING BETWEEN PORTS IS 14.25mm. 8 REFERENCE APPLICATION SPEC. 114-13120, HOLE A, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 9 REFERENCE APPLICATION SPEC. 114-13120, HOLE B, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 2X 14 0.1 PORT OPENING 00 P LTR DESCRIPTION DWN APVD A RELEASED PER ECO-12-013192 05SEP2012 BMM MRS A1 RELEASED PER ECO-13-0014600 12OCT2013 PP SH MINIMUM PC BOARD THICKNESS: SINGLE SIDED: 1.5mm D DIMENSION APPLIES PRIOR TO INSERTION OF SFP MODULE. ( 49.2 ) 2198224-5,6,7,8 FINISHED ASSEMBLY C DATE 12. PRODUCT COMPLIES WITH SPECIFICATION SFF-8433 IMPROVED PLUGGABLE FORM FACTOR FOR SFP+ GANGED CAGES. 6. INTERPRETATION OF DATUM REFERENCE FRAME IN ACCORDANCE WITH SECT 4.4.1.1 OR ASME Y14.5M-1994. FIN TYPE HEAT SINK REVISIONS DIST 11. CERTAIN MATING TRANCEIVERS MAY REQUIRE ADDITIONAL PCB THICKNESS THAT WOULD NEED TO BE DETERMINED BY THE CUSTOMER. 5. MATES WITH SFP MSA COMPLIANT RECIEVERS. D 1 13 A MAX 2X 8.95 0.15 PORT OPENING ( 14.25 ) ( 7.125 ) ( 28.75 ) MEASURED ACROSS CAGE SIDES 34.25 C ( 9.7 ) ( 2.05 ) TYP 38.9 MIN 0.3 8X R 0.3 MAX GUIDE PINS B B 2X 10.4 ( 1.5 ) MIN 10 PCB THICKNESS +0.10 -0.14 TOP OF PCB TO INSIDE OF BEZEL CUTOUT 0.23 ( 35.4 ) 2198224 MOUNTED ON PC BOARD SHOWN THRU RECOMMENDED BEZEL FIN TYPE 22.5 FIN TYPE 15.5 FIN TYPE FIN TYPE 2X 29.7 RECOMMENDED BEZEL CUT-OUT SINGLE SIDED APPLICATIONS SCALE 4:1 THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 0.13 0.1 0.08 .05 .05 FINISH 1 4805 (3/11) TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES PCI 15.5 HEAT SINK 2 NETWORKING, SHORT 13.2 PCI 12OCT2011 CHK 12OCT2011 APVD 12OCT2011 B. MATTHEWS M. SCHMITT M. SCHMITT 108-2364 APPLICATION SPEC 114-13120 WEIGHT - Customer Drawing 2198224-5 2198224-4 2198224-3 SAN A MAX DWN 2198224-7 NETWORKING, TALL 18.1 PRODUCT SPEC 1 2198224-6 13.2 PIN TYPE A SAN NETWORKING, SHORT 22.5 PIN TYPE 2198224-8 18.1 PIN TYPE PIN TYPE NETWORKING, TALL 2198224-2 2198224-1 PART NUMBER APPLICATION A TE Connectivity NAME SFP+ ENHANCED 1X2 CAGE ASSEMBLY, PRESS-FIT, EMI GASKET WITH HEATSINK SIZE CAGE CODE A1 00779 DRAWING NO 2198224 SCALE 5:1 SHEET 1 RESTRICTED TO OF - 2 REV A1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC BY - 2X 7 2X 7.125 7 2X 2.325 11.925 REVISIONS DIST GP ALL RIGHTS RESERVED. 1 00 P LTR 2X 6.5 DWN 3X 2 20X 12X ( THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) - - 0.5 0.95 ) 4 0.8 1.4 9 20X PLATING REQUIRED 2 0.05 D 4X 4.1 0.05 F SEE DETAIL D 1.55 E 1 2X 30 ( 9.6 ) 27.5 DETAIL F SCALE 10:1 4X 25.9 22.5 2X 17.8 4X 41.3 15 2X 10 1.1 CROSS-HATCHED AREA DENOTES EXPOSED CHASSIS GROUND 2X 26.8 5 2X 2 2X 21.6 2X 5 B B 2X 12.05 9.5 MAX G DETAIL SCALE 10:1 2.5 MIN A ( 1.05 ) PLATING REQUIRED 4 C 3X 42.3 2X 20 SEE DETAIL 8 C 3 3 B G 4 1 BCS 14X o2 1 4X 7X ( 1.05 ) 4 8 PLATING REQUIRED 14.25 5X 28.5 RECOMMENDED PCB CONFIGURATION WITH KEEP-OUT AREAS SINGLE SIDED APPLICATIONS SCALE 8:1 CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) A THIS DRAWING IS A CONTROLLED DOCUMENT. 10 DIMENSIONS: mm MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.13 0.1 0.08 .05 .05 DWN 12OCT2011 CHK 12OCT2011 APVD 12OCT2011 B. MATTHEWS M. SCHMITT M. SCHMITT PRODUCT SPEC 108-2364 APPLICATION SPEC 1 114-13120 WEIGHT - Customer Drawing 4805 (3/11) 4X 4.1 0.05 4X 32.1 A - 0.03 1.55 C APVD 4X 2.875 18X D DATE SEE SHEET 1 - 2X 12.25 7 DESCRIPTION TE Connectivity NAME SFP+ ENHANCED 1X2 CAGE ASSEMBLY, PRESS-FIT, EMI GASKET WITH HEATSINK SIZE CAGE CODE A1 00779 DRAWING NO 2198224 SCALE 5:1 SHEET 2 RESTRICTED TO OF - 2 REV A1