2198225-1

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY - 5 1 2 D FINISH: HEATSINK: ELECTROLESS NICKEL HEATSINK/LIGHTPIPE CLIP: PASSIVATE 10 3 DATUM AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 4 PADS AND VIAS CHASSIS GROUND. 5. MATES WITH SFP MSA COMPLIANT RECIEVERS. 6. INTERPRETATION OF DATUM REFERENCE FRAME IN ACCORDANCE WITH SECT 4.4.1.1 OR ASME Y14.5M-1994. 2198225 FINISHED ASSEMBLY SCALE 4:1 GP MATERIAL: CAGE ASSEMBLY: 0.25mm THICK NICKEL SILVER ALLOY GASKET RETENTION PLATE: STAINLESS STEEL EMI GASKET: PLATED FILLED SILICONE HEATSINK/LIGHTPIPE CLIP: STAINLESS STEEL HEATSINK: ALUMINUM LIGHTPIPE: POLYCARBONATE, CLEAR 7 HOLE PATTERN REPEATS FOR EACH PORT, SPACING BETWEEN PORTS IS 14.25mm. 8 REFERENCE APPLICATION SPEC. 114-13120, HOLE A, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 9 REFERENCE APPLICATION SPEC. 114-13120, HOLE B, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS. 1 REVISIONS DIST 00 P LTR DESCRIPTION DATE DWN APVD A RELEASED PER ECO-12-013192 06SEP2012 BMM MRS A1 REVISED PER ECR-19-000118 04JAN2018 IT SH MINIMUM PC BOARD THICKNESS: SINGLE SIDED: 1.5mm 11. CERTAIN MATING TRANCEIVERS MAY REQUIRE ADDITIONAL PCB THICKNESS THAT WOULD NEED TO BE DETERMINED BY THE CUSTOMER. D 12. PRODUCT COMPLIES WITH SPECIFICATION SFF-8433 IMPROVED PLUGGABLE FORM FACTOR FOR SFP+ GANGED CAGES. 13 DIMENSION APPLIES PRIOR TO INSERTION OF SFP MODULE. 14 HEATSINK, HEATSINK CLIP, AND LIGHTPIPE SHIPPED UNASSEMBLED TO CAGE ASSEMBLY. CAGE ASSEMBLY TO BE PRESSED INTO PCB PRIOR TO ATTACHING HEATSINK, HEATSINK CLIP, AND LIGHTPIPE TO THE CAGE ASSEMBLY. 15 PACKAGED AS A COMPLETE ASSEMBLY. 2X 14 0.1 PORT OPENING 2X ( 54.8 ) 4X ( 2.7 ) C C 13 A MAX 2X ( 15.9 ) 2X ( 15 ) 2X 8.95 0.15 PORT OPENING ( 9.7 ) ( 1.7 ) ( 2.05 ) TYP 4X ( 3.5 ) B B 4X ( 2.5 ) ( 7.125 ) ( 14.25 ) ( 33.85 ) ( 28.75 ) MEASURED ACROSS CAGE SIDES 15 ( 3.25 ) 15 14 ( 3.25 ) 14 22.5 NETWORKING, TALL 2198225-4 SAN 2198225-2 18.1 NETWORKING, SHORT 13.2 PCI 15.5 A MAX A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES MATERIAL 0.13 0.1 0.08 .05 .05 FINISH 1 4805 (3/11) TOLERANCES UNLESS OTHERWISE SPECIFIED: 2 DWN 14OCT2011 CHK 14OCT2011 APVD 14OCT2011 B. MATTHEWS M. SCHMITT M. SCHMITT PRODUCT SPEC 108-2364 APPLICATION SPEC 1 114-13120 WEIGHT - RESTRICTED CUSTOMER 2198225-3 2198225-1 PART NUMBER APPLICATION A TE Connectivity NAME SFP+ ENHANCED 1X2 CAGE ASSEMBLY, PRESS-FIT, EMI GASKET WITH HEATSINK AND LIGHTPIPE SIZE CAGE CODE A1 00779 DRAWING NO 2198225 SCALE 6:1 SHEET 1 RESTRICTED TO OF 3 REV A1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. BY - 1 REVISIONS DIST 00 P LTR - 38.9 29.7 DESCRIPTION DATE SEE SHEET 1 DWN - - APVD - 0.3 D D 2X 10.375 14.25 8X 4X 6.5 2.54 GUIDE PINS 10.0275 10.4 C 4X R 0.3 MAX +0.10 0.23 -0.14 TOP OF PCB TO INSIDE OF BEZEL CUTOUT 34.25 C ( 35.4 ) ( 1.5 ) MIN PCB THICKNESS 10 MIN RECOMMENDED BEZEL CUTOUT SCALE 4:1 2198225 MOUNTED ON PC BOARD SHOWN THRU RECOMMENDED BEZEL B B 2198225 MOUNTED ON PCB SHOWN THRU RECOMMENDED BEZEL A A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.13 0.1 0.08 .05 .05 DWN 14OCT2011 CHK 14OCT2011 APVD 14OCT2011 B. MATTHEWS M. SCHMITT M. SCHMITT PRODUCT SPEC 108-2364 APPLICATION SPEC 1 114-13120 WEIGHT - RESTRICTED CUSTOMER 4805 (3/11) TE Connectivity NAME SFP+ ENHANCED 1X2 CAGE ASSEMBLY, PRESS-FIT, EMI GASKET WITH HEATSINK AND LIGHTPIPE SIZE CAGE CODE A1 00779 DRAWING NO 2198225 SCALE 5:1 SHEET 2 RESTRICTED TO OF 3 REV A1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC BY - 2X 7 4X 4X q FOR LED PLACEMENT AND LIGHTPIPE COVERAGE AREA 7 2X 11.925 7 7.125 2X 6.5 4X 2.875 2.325 20X LTR DESCRIPTION DATE SEE SHEET 1 0.5 DWN APVD - - - 0.03 18X 3X 2 12X ( 0.95 ) 4 0.8 1.4 9 20X PLATING REQUIRED SEE DETAIL P 2X 12.25 D THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) 00 - 3.875 2X REVISIONS DIST GP ALL RIGHTS RESERVED. 1 2 0.05 D E 1.55 SEE DETAIL 4X 4.1 0.05 D F 1.55 4X 4.1 0.05 E 1 4X 32.1 ( 9.6 ) 2X 30 C DETAIL F SCALE 10:1 27.5 1.1 4X 25.9 CROSS-HATCHED AREA DENOTES EXPOSED CHASSIS GROUND 4X 44.55 22.5 C 3X 42.3 2X 20 2X 17.8 4X 41.3 15 2X 2 2X 10 2X 26.8 5 2X 12.05 G DETAIL SCALE 10:1 2X 21.6 B B 6.5 2X 5 9.5 MAX 4X 3.56 0.1 -B2.5 MIN A ( 1.05 ) PLATING REQUIRED 4 8 3 A BCS C 3 SEE DETAIL G 4 1 14X 4X 2.54 o2 1 4X 13X ( 1.05 ) 4 0.1 8 DETAIL E SCALE 10:1 PLATING REQUIRED 14.25 5X A 28.5 RECOMMENDED PCB CONFIGURATION WITH KEEP-OUT AREAS SINGLE SIDED APPLICATIONS SCALE 8:1 10 THIS DRAWING IS A CONTROLLED DOCUMENT. CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) DIMENSIONS: mm MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 0.13 0.1 0.08 .05 .05 DWN 14OCT2011 CHK 14OCT2011 APVD 14OCT2011 B. MATTHEWS M. SCHMITT M. SCHMITT PRODUCT SPEC 108-2364 APPLICATION SPEC 1 114-13120 WEIGHT - RESTRICTED CUSTOMER 4805 (3/11) TE Connectivity NAME SFP+ ENHANCED 1X2 CAGE ASSEMBLY, PRESS-FIT, EMI GASKET WITH HEATSINK AND LIGHTPIPE SIZE CAGE CODE A1 00779 DRAWING NO 2198225 SCALE 5:1 SHEET 3 RESTRICTED TO OF 3 REV A1