2198722-1

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 20 LOC ALL RIGHTS RESERVED. BY - 2 1X4 CAGE SUB-ASSEMBLY D PCB GASKET 2198722-1 SCALE 5:1 00 MINIMUM PC BOARD THICKNESS: SINGLE SIDED = 1.45mm BELLY TO BELLY = 3mm 3 PADS AND VIAS CHASSIS GROUND 4 DATUM AND BASIC DIMENSION ESTABLISHED BY CUSTOMER 5. MATES WITH SFP MSA COMPLIANT TRANSCEIVERS 6. INTERPRETATION OF DATUM REFERENCE FRAME IN ACCORDANCE WITH SECT 4.4.1.1 OF ASME Y14.5M-1994 7 REFERENCE APPLICATION SPEC. 114-13120, HOLE A, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS 8 REFERENCE APPLICATION SPEC. 114-13120, HOLE B, FOR RECOMMENDED DRILL HOLE DIAMETER AND PLATING THICKNESS 9 HOLE PATTERN REPEATS FOR EACH PORT, SPACING BETWEEN PORTS IS 14.25mm 10. 11 REVISIONS DIST 2 GASKET RETENTION PLATE EMI GASKET GP 1. MATERIAL: CAGE ASSEMBLY: NICKEL SILVER ALLOY GASKET RETENTION PLATE: STAINLESS STEEL EMI GASKET: PLATED FILLED SILICONE PCB GASKET: RF ABSORBER 1 P LTR DESCRIPTION DATE DWN APVD A REVISED PER ECO-15-002647 05MAR2015 AP MS B REVISED PER ECO-16-014593 13FEB2017 JW SH D PRODUCT COMPLIES WITH SPECIFICATION SFF-8433, IMPROVED PLUGGABLE FORM FACTOR FOR SFP+ GANGED CAGES CONTACT STANDOFF WILL PIERCE GASKET WHEN PROPERLY PRESSED INTO PCB. ( 49.1 ) C C ( 10.08 ) 11 22X 4X 8.95 0.15 PORT OPENING ( 14.06 ) ( 9.83 ) ( 2.05 ) 4X 14 0.1 PORT OPENING ( 49.8 ) PCB GASKET ( 56.75 ) B B ( 59.28 ) PCB GASKET ( 61.85 ) 2198722-1 PART NUMBER A THIS DRAWING IS A CONTROLLED DOCUMENT. DWN M.E. COWHER 27DEC2012 01FEB2013 M.D. MORRISON APVD 01FEB2013 M.J. PHILLIPS TE Connectivity CHK DIMENSIONS: mm MATERIAL 4805 (3/11) SEE NOTE 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.25 0.25 0.25 0.25 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - NAME PRODUCT SPEC 108-2364 APPLICATION SPEC 1 $ 114-13120 WEIGHT - Customer Drawing A SIZE CAGE ASSEMBLY, ENHANCED, PRESS-FIT, 1X4, zSFP+ - CAGE CODE A1 00779 DRAWING NO 2198722 SCALE 4:1 SHEET RESTRICTED TO 1 OF - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY - 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR - DESCRIPTION SEE SHEET 1 2X 58.4 D DATE DWN APVD - - - GUIDE PINS D 8X R 0.3 MAX 2X 10.6 60.75 0.19 0.1 BEZEL CUT-OUT BELOW PCB SURFACE 2 ( 1.45 ) MIN RECOMMENDED BEZEL OPENING SINGLE SIDED APPLICATIONS SCALE 2:1 3.5 0.3 ( 35.4 ) MOUNTED ON PC BOARD SHOWN THRU RECOMMENDED BEZEL SCALE 5:1 C C GUIDE PINS 4X 58.4 16X 0.19 0.1 BEZEL CUT-OUT BELOW PCB SURFACE R 0.3 MAX 2 (3) 4X 10.6 13.22 0.19 0.1 BEZEL CUT-OUT ABOVE PCB SURFACE B B 60.75 MIN RECOMMENDED BEZEL OPENING BELLY TO BELLY APPLICATIONS SCALE 2:1 3.5 0.3 ( 35.4 ) MOUNTED BELLY TO BELLY ON PC BOARD SHOWN THRU RECOMMENDED BEZEL SCALE 5:1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DWN M.E. COWHER 27DEC2012 01FEB2013 M.D. MORRISON APVD 01FEB2013 M.J. PHILLIPS TE Connectivity CHK DIMENSIONS: mm MATERIAL 4805 (3/11) SEE NOTE 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.25 0.25 0.25 0.25 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - NAME PRODUCT SPEC 108-2364 APPLICATION SPEC 1 $ 114-13120 WEIGHT - Customer Drawing SIZE CAGE ASSEMBLY, ENHANCED, PRESS-FIT, 1X4, zSFP+ - CAGE CODE A1 00779 DRAWING NO 2198722 SCALE 5:1 SHEET RESTRICTED TO 2 OF - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. 20 4 3 2 20 LOC GP ALL RIGHTS RESERVED. BY - 4X 4X 7.125 9 2.325 9 4X 12.25 9 1 REVISIONS DIST 00 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 4X 6.5 11.925 COPYRIGHT 5 20X ( 4X C RELEASED FOR PUBLICATION 6 0.95 ) 3 PLATING REQUIRED 8 4X 2.88 3X ( 2 ) F SEE DETAIL D D 32.1 30 THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) 27.5 25.9 22.5 CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) 20 17.8 15 3 7 ( 42.3 10 1.05 ) -CPLATING REQUIRED 21.6 13X ( 9.5 MAX 5 0.03 9X o2 57 1 B 0.8 1.4 2 7 RECOMMEND PCB CONFIGURATION WITH KEEP-OUT AREAS FOR SINGLE SIDED APPLICATIONS SCALE 5:1 B 20X 42.75 0 -B- 22X 28.5 BSC MIN 14.25 3.75 1 4 4 3 1.05 ) PLATING REQUIRED -A- 0.5 C 26.8 0 20X G SEE DETAIL 5 C 41.3 12.05 0.05 20 11 1.55 4.1 0.05 2 -D1.55 0.05 -E- 1 10 CROSS-HATCHED AREA DENOTES EXPOSED CHASSIS GROUND 4.1 1.1 A 1 9X 0.8 DETAIL G 4X INDIVIDUALLY SCALE 10:1 A THIS DRAWING IS A CONTROLLED DOCUMENT. 4805 (3/11) M.E. COWHER 27DEC2012 01FEB2013 M.D. MORRISON APVD 01FEB2013 M.J. PHILLIPS TE Connectivity CHK DIMENSIONS: ( 9.6 ) DETAIL F 4X INDIVIDUALLY SCALE 10:1 DWN mm MATERIAL SEE NOTE 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 0.08 0.05 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - NAME PRODUCT SPEC 108-2364 APPLICATION SPEC 1 $ 114-13120 WEIGHT - Customer Drawing SIZE CAGE ASSEMBLY, ENHANCED, PRESS-FIT, 1X4, zSFP+ - CAGE CODE A1 00779 DRAWING NO 2198722 SCALE 5:1 SHEET RESTRICTED TO 3 OF - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY - 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 11.925 9 4X 28X ( 0.95 ) 3 8 PLATING REQUIRED D D 32.1 30 27.5 22.5 20 17.8 C C 15 10 5 3 7 ( 1.05 ) -CPLATING REQUIRED 0 28X ( 1.05 ) 3 7 PLATING REQUIRED 5 B 57 42.75 14.25 MIN 0 3.75 28.5 B RECOMMEND PCB CONFIGURATION WITH KEEP-OUT AREAS FOR BELLY TO BELLY APPLICATIONS SAME AS SINGLE SIDE APPLICATION, EXCEPT AS SHOWN SCALE 6:1 A A THIS DRAWING IS A CONTROLLED DOCUMENT. DWN M.E. COWHER 27DEC2012 01FEB2013 M.D. MORRISON APVD 01FEB2013 M.J. PHILLIPS TE Connectivity CHK DIMENSIONS: mm MATERIAL 4805 (3/11) SEE NOTE 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.1 0.08 0.05 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - NAME PRODUCT SPEC 108-2364 APPLICATION SPEC 1 $ 114-13120 WEIGHT - Customer Drawing SIZE CAGE ASSEMBLY, ENHANCED, PRESS-FIT, 1X4, zSFP+ - CAGE CODE A1 00779 DRAWING NO 2198722 SCALE 5:1 SHEET RESTRICTED TO 4 OF - 4 REV B