2203771-1

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION TE CONNECTIVITY CORPORATION. 6 5 4 3 2 1 20 REVISIONS ALL RIGHTS RESERVED. P ( 5.20 ) ( 3.40 ) ( 0.60 ) LTR ( 1.20 ) 1 DESCRIPTION DATE DWN APVD A RELEASED PER ECO-15-012149 21AUG2015 DLD MDB B REVISED PER ECO-16-010785 10NOV2016 DLD JLT C REVISED PER ECO-17-003504 14MAR2017 DLD JLT ISL AND CPA (WHEN APPLICABLE) ARE SHIPPED IN THEIR PRE-LATCHED POSITIONS. 2. TERMINALS SOLD SEPARATELY. FOR USE WITH TE MCON 1.2mm CLEAN BODY CONTACT WITH WIRE SEAL. SEE TABLE. 3. APPLICABLE INTERFACE DRAWINGS: EWCAP 120-S-003-1-Z01 AND 120-S-003-1-Z02. D 4 KEY CODE A SCALE 4:1 KEY CODE B 12 SCALE 4:1 KEY CODE C 12 SCALE 4:1 19.40 26.50 C KEY CODE D 12 SCALE 4:1 MINIMUM FEED THROUGH CONDITION WITH 1.0mm CLEARANCE ALL AROUND. 5. TRACEABILITY CODE (YY = TWO DIGIT YEAR, JJJ = 3 DIGIT JULIAN DAY, S = 1 DIGIT SHIFT). 12 6. FOR OPTIONAL TERMINAL CAVITY BLOCKING, CONTACT TE SALES REPRESENTIVE OR CUSTOMER SERVICE. 0.20 7 SEE INSTRUCTION SHEET 408-32103 FOR CONNECTOR SERVICE AND ISL OPERATION. ISL ACTUATION DISTANCE IS 2.0mm. 8 CONTACT PLATING AND APPLICABLE INDIVIDUAL WIRE SEAL ARE APPLICATION DEPENDENT. CONTACT TE SALES REPRESENTATIVE OR CUSTOMER SERVICE FOR DETAILS. 9 FOR WIRE CRIMP DETAILS, SEE TE APPLICATION SPECIFICATION 114-18464. 10 DOCUMENTED I.C.D. IS SPECIFIED TO MEET MOST WIRE SEAL APPLICATIONS. HOWEVER, I.C.D. IS HIGHLY DEPENDENT ON INSULATION TYPE AND OD. SUFFICIENT GRIP OF THE WIRE SEAL MUST BE OBTAINED SUCH THAT WIRE SEAL DOES NOT DISPLACE FROM INSULATION GRIP DURING CONTACT INSERTION INTO CONNECTOR HOUSING. THE WIRE SEAL SHALL NOT BE CRIMPED TOO TIGHTLY THAT THE WIRE SEAL TEARS DURING THE CRIMPING OPERATION. ISOMETRIC VIEW SCALE 3:1 0.20 D C 11. CONNECTOR VALIDATION PER USCAR-2 (REV6) T4,V4,S3 WITH THE FOLLOWING EXCEPTIONS: PRIMARY TERMINAL RETENTION FORCE > 25 NEWTONS. 12 KEY CODE DIMENSIONS ARE SHOWN WITH ISL IN PRE-LATCHED POSTION. FOR DIMENSION OF KEY WITH ISL IN FINAL POSITION, ADJUST SHOWN DIMENSIONS BY 2.0mm. 13. NOTE REMOVED 1 14 7 NOTE REMOVED ( 14.6 ) ( 4 22.92 ) 1 CPA, QTY:1 WHEN APPLICABLE COLOR: RED 1 ISL, QTY:1 COLOR SEE TABLE B 18.05 (4) TYP ISL SHOWN IN FINAL (LOCKED) POSITION SCALE 5:1 REF ONLY B 0.20 PLUG HOUSING, QTY:1 COLOR:BLACK PERIMETER SEAL, QTY:1 CPA (YES/NO) A THIS DRAWING IS A CONTROLLED DOCUMENT. I.C.D. WIRE CRIMP DIMENSIONS 4805 (3/13) INSULATION CRIMP DIMENSIONS 150 $ C 8 MAX TEMP 1418844 1670146 1418850 FEMALE TERMINAL P/N DIMENSIONS: 9 W.C.H 1-2203771-4 DK GRAY KEY CODE C 1-2203771-3 LT GRAY KEY CODE B 1-2203771-2 BLUE KEY CODE A 1-2203771-1 BLUE KEY CODE D 2203771-4 DK GRAY KEY CODE C 2203771-3 LT GRAY KEY CODE B 2203771-2 BLUE KEY CODE A 2203771-1 ISL COLOR KEY CONFIGURATION PART NUMBER NO W.C.W. W.C.H. KEY CODE D YES X-X SECTION SHOWN WITH CPA AND ISL IN PRE-LATCHED POSITION ISL SHOWN IN PRE-LATCHED (AS-SHIPPED) POSITION BLUE 9 W.C.W 10 I.C.D mm 8 WIRE SEAL PART NUMBER MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.3 0.15 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30MAY2013 CHK 30MAY2013 APVD 30MAY2013 VISHGNU.P MD BROWN MD BROWN TE Connectivity NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - CUSTOMER DRAWING A CAGE CODE A1 00779 PLUG ASSEMBLY, SEALED, 3 POSITION, MCON DRAWING NO 2203771 SCALE 5:1 SHEET RESTRICTED TO 1 OF - 1 REV C