2266165-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION 2266165 -2 F 7-2266165-1 F 7-2266165-2 F 7- 2266165 -7 A 4 3 2 LOC DESCRIPTION F 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2266165 -1 6 FEED TYPE REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR MECHANICAL FINE CRIMP HEIGHT ADJUST FINE CRIMP HEIGHT ADJUST PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD D1 ECR-19-007996 20MAY2019 FJ MP E ECR-19-005769 27JUN2019 FJ TE F ECR-20-003599 10MAR2020 JWC GB F1 ECR-21-003488 22MAR2021 FJ RK MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 1.40 mm [.055] 1.83 mm [.072] APPLICATOR INSTRUCTIONS 408-35042 - 3 TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 3.05-3.35 mm [.120-.132 IN] TERMINAL APPLICATION SPECIFICATION C 1801528-1 114-15077 - TERMINALS APPLIED TE TERMINAL n 5-1379419-1 - - - 1.25-1.70mm [.049-.067 IN] - - - - - - 7 1801528-2 C1__DWG_PN_1_1 - INSULATION DIAMETER RANGE - TE TERMINAL C1__DWG_PN_1_0 - TE CRIMP SPECIFICATION MICRO QUADOCK SYSTEM TERMINAL NAME: - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 5-1379419-2 C1__DWG_PN_3_0 1379419-1 TE TERMINAL 1379419-2 C1__DWG_PN_3_1 - C1__DWG_PN_4_0 - C1__DWG_PN_4_1 - WIRE SIZE 0.50mm2 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 0.83+/-0.03 [.033+/-.001] 0.74+/-0.03 [.029+/-.001] - CRIMP HEIGHT 4 REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 4.6 5.5 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - 1 2 B 3 4 5 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. REFER TO APPLICATION SPECIFICATION,114-18021,PAGE 8,NOTE 3 2 CONCERNING CRIMPING 0.50mm WIRE. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 - POSITION THE HOLD DOWN, ITEM 18, IN ORIENTATION 1 REFER TO SHEET 2. - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE.CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - 7 - 1 - 1 1 1 - A 1 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 2 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL - 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SPACER, CRIMPER SCR, SKT HD CAP, RoHS, M3 X 8.0 FENCE DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 6.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED TERMINAL HOLD DOWN INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .055 SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE, F DWN 13JAN2014 CHK 13JAN2014 APVD 13JAN2014 BOB HIGMAN G.BAILEY M.CLIFFORD - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 1-18028-2 1 2844908 1 2844907 1 1-690438-0 2 2168083-1 1 455888-5 2 2168083-1 1 1633782-2 1 1803607_3 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 2 2-18032-5 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 2 2168083-5 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1752356-6 2 2079383-5 2 2-2844962-4 1 2844992-3 1 455888-3 2 22283-1 1 356835-1 1 240792-1 1 1320928-2 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 2217529 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-1 1 1-1338690-2 1 4-240641-2 1 2119757-4 1 238011-8 1 2119784-2 1 455888-1 1 1-562108-5 248 244 243 242 241 239 238 164 119 99 98 96 95 82 79 78 71 70 69 67 66 61 60 59 56 54 53 49 48 47 46 44 41 34 33 30 29 28 27 26 25 24 23 21 20 19 18 13 12 11 10 9 8 7 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119082-5 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH PART NO 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. mm -1 1 -77 -72 -71 -2 DIMENSIONS: 1 1 1 1 2 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 2 1 1 2 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 2 1 1 - 4 2 2 - 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 2 1 2 1 1 2 1 2 1 1 2 1 1 1 1 2 1 1 1 1 - REF REF 1 1 1 1 REF 1 1 - - REF 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-5 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-18028-2 2844908-1 2844907-1 1-690438-0 2168083-1 455888-5 2168083-1 1633782-2 1803607-3 2119791-5 2119943-1 2119740-1 2168078-1 2-18032-5 2168083-2 5-18022-5 1338685-1 2168083-3 2168083-5 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1752356-6 2079383-5 2-2844962-4 2844992-3 455888-3 22283-1 356835-1 240792-1 1320928-2 980371-4 2168083-2 1-18028-2 2119533-1 2217529-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-1 1-1338690-2 4-240641-2 2119757-4 238011-8 2119784-2 455888-1 1-562108-5 - Ocean Side Feed Applicator - DRAWING NO 2266165 SCALE 5:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 44 56 2 244 PNEUMATIC 243 53 7 18 242 3 8 REF 4.3 0.5 7 82 A 2 1 238 34 REF 1 70 69 TERMINAL SUPPORT LOCATION 2 3 59 1 4 C 28 5 C 41 SEE DETAIL A 56 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 44.99 0.05 66 33 2 164 67 24 30 DETAIL A POSITION TOP EDGE OF HOLD DOWN AGAINST BOTTOM SURFACE OF RAM A 95 RAM SETUP 19 96 20 78 B 21 29 B 9 1 12 241 13 1 30 REF 29 REF CAM POSITIONS 79 25 27 61 26 23 46 98 99 34 54 8 1 60 54 10 1 119 11 30mm STROKE 30mm STROKE 30mm STROKE ITEM 30 LOCATED AT FRONT HOLES 6.4 47 248 48 0.5 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 13JAN2014 CHK 13JAN2014 APVD 13JAN2014 BOB HIGMAN G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266165 SCALE 5:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2266165 -1 F FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2266165 -7 A CRIMP TOOLING KIT - F 3 2 LOC PART NUMBER 2- 2266165 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 1.40 mm [.055] 1.83 mm [.072] APPLICATOR INSTRUCTIONS 408-35042 - 1 - 1 - 3 TE TERMINAL MICRO QUADOCK SYSTEM TERMINAL NAME: WIRE STRIP LENGTH 3.05-3.35 mm [.120-.132 IN] TERMINAL APPLICATION SPECIFICATION TE TERMINAL 1801528-1 114-15077 - TERMINALS APPLIED C n 1801528-2 C1__DWG_PN_1_1 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_3_0 1379419-1 TE TERMINAL - 1379419-2 C1__DWG_PN_3_1 0.50mm2 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 0.83+/-0.03 [.033+/-.001] 0.74+/-0.03 [.029+/-.001] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 4.6 5.5 - REFER TO APPLICATION SPECIFICATION,114-18021,PAGE 8,NOTE 3 2 CONCERNING CRIMPING 0.50mm WIRE. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 POSITION THE HOLD DOWN, ITEM 18, IN ORIENTATION 1 REFER TO SHEET 4. 1 2 2 1 1 1 1 1 1 1 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 1 - 1 1 1 1 - A 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 1 1 1 - 1 2 - - 1 2 1 - 7 1 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE.CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 5 2 1 - - 2 2 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 2 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 - - 1 1 - 3 1 1 - B 2 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 2 - 2 2 1 - RECOMMENDED SPARE PARTS 1 2 - 1 1 1 - W1__FA_SETTING_2 1 1 - W1__FA_SETTING_1 1 1 - CRIMP HEIGHT 4 REFERENCE SETTING 1 1 - WIRE SIZE 1 1 C1__DWG_PN_4_1 1 1 - C1__DWG_PN_4_0 4 - C1__DWG_PN_2_0 1 4 - - - 1 - - - 1 - 7 TE TERMINAL C1__DWG_PN_1_0 - - REF REF - 1.25-1.70mm [.049-.067 IN] 1 1 - INSULATION DIAMETER RANGE 1 - - TE CRIMP SPECIFICATION 1 1 - TERMINAL DATA: 1 1 - 2119082-5 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2844908-1 2844907-1 1-690438-0 2168083-1 455888-5 2168083-1 1633782-2 1803607-3 2119791-5 2119943-1 2119740-1 2168078-1 2-18032-5 5-18022-5 1338685-1 2168083-5 18023-9 2119652-1 1803602-1 1752356-6 2079383-5 2-2844962-4 2844992-3 455888-3 22283-1 356835-1 240792-1 1320928-2 980371-4 2168083-2 1-18028-2 2119533-1 2217529-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-1 1-1338690-2 4-240641-2 2119757-4 238011-8 2119784-2 455888-1 1-562108-5 1 1 1 1 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 13JAN2014 CHK 13JAN2014 APVD 13JAN2014 BOB HIGMAN G.BAILEY M.CLIFFORD - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2844908 1 2844907 1 1-690438-0 2 2168083-1 1 455888-5 2 2168083-1 1 1633782-2 1 1803607_3 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 2 2-18032-5 1 5-18022-5 1 1338685-1 2 2168083-5 3 18023-9 1 2119652 1 1803602-1 1 1752356-6 2 2079383-5 2 2-2844962-4 1 2844992-3 1 455888-3 2 22283-1 1 356835-1 1 240792-1 1 1320928-2 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 2217529 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-1 1 1-1338690-2 1 4-240641-2 1 2119757-4 1 238011-8 1 2119784-2 1 455888-1 1 1-562108-5 244 243 242 241 239 238 164 151 144 143 142 141 140 119 99 98 96 95 82 79 78 71 70 69 67 66 61 59 56 53 49 48 41 34 33 30 29 28 27 26 25 24 23 21 20 19 18 13 12 11 10 9 8 7 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2079764_APP TE Connectivity APPLICATION SPEC - 1 2119082-5 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SPACER, CRIMPER SCR, SKT HD CAP, RoHS, M3 X 8.0 FENCE DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 6.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED TERMINAL HOLD DOWN INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .055 SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE, F Ocean Side Feed Applicator - DRAWING NO 2266165 SCALE 5:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL 140 A D 244 239 4.3 243 59 242 56 PNEUMATIC 53 8 REF TERMINAL SUPPORT LOCATION 7 238 82 1 59 1 70 69 2 3 C 1 4 28 SEE DETAIL A REF 3 2 D 0.5 34 7 18 A 2 56 35.96 5 0.05 C 41 POSITION TOP EDGE OF HOLD DOWN AGAINST BOTTOM SURFACE OF RAM FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) RAM SETUP 66 164 2 33 67 24 30 DETAIL A A 95 19 20 96 21 78 B 9 29 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 13 CAM POSITIONS 30mm STROKE 79 27 30mm STROKE 30mm STROKE 142 25 61 26 23 141 98 99 34 143 8 1 144 143 10 1 29 B 30 REF REF 1 119 6.4 11 0.5 FEED TRACK POSITION GUIDE BY INSULATION BARREL 151 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 13JAN2014 CHK 13JAN2014 APVD 13JAN2014 BOB HIGMAN G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266165 SCALE 5:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F1