2266237-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 6 5 4 3 2 20 PART NUMBER REVISION 2266237 -1 DESCRIPTION C FINE CRIMP HEIGHT ADJUST C 2266237 -5 MECHANICAL D FINE CRIMP HEIGHT ADJUST C SUPERSEDED BY 5-2266755-1 PNEUMATIC SERVO LATCH PLATE FINE CRIMP HEIGHT ADJUST 2266237 -6 C NON-CRIMP HEIGHT ADJUST 2266237 -7 C FINE CRIMP HEIGHT ADJUST 7- 2266237 -7 A - 4 CRIMP TOOLING KIT SUPERSEDED BY 5-2266755-2 - 4 SERVO LATCH PLATE 11 NONE - - OBSOLETE 6 OBSOLETE - OBSOLETE - - - CRIMP WIRE INSUL APPLICATOR DATA SIZE - - TYPE - F F 0.66 mm [.026] 0.69 mm [.027] APPLICATOR INSTRUCTIONS 408-10389 - - - JST TERMINAL TERMINAL DATA: JST CRIMP SPECIFICATION WIRE STRIP LENGTH 0.80-1.50 mm [.031-.059 IN] C - AMP MCP 2.8K FLAT TYPE RECEPTACLE TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION n CHM-1-165 - - INSULATION DIAMETER RANGE - 0.53-0.77 mm [.021-.030 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 2113441-1 JST TERMINAL SSHL-003T-PO.2 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 2113441-2 C1__DWG_PN_3_0 C1__DWG_PN_3_1 6 JST TERMINAL SSHL-003GA1-P0.2 C1__DWG_PN_4_0 - C1__DWG_PN_4_1 - WIRE SIZE 28 AWG 30 AWG 32 AWG B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.45+/-0.02 [.018+/-.001] 0.42+/-0.02 [.017+/-.001] 0.40+/-0.02 [.016+/-.001] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY CRIMP HEIGHT REFERENCE SETTING 7.9 W1__DWG_CRIMP_HT_2 8.2 W1__DWG_CRIMP_HT_3 - 9 7.5 W1__DWG_CRIMP_HT_1 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 7 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 8 9 10 11 A 12 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37. GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 2266237 2266237 2266237 2266237 - -4 -4 -5 -6 - & 180. - & 252. - MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF THIS APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER TERMINATING UNIT. 6 5.35 . - 1 1 1 1 1 1 - -77 -7 1 1 1 1 1 2 -6 1 1 1 1 1 1 2 -5 1 1 1 1 1 1 1 1 1 - -2 - 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-1 2079764-1 2119083-1 2168400-6 -1 PART NO 1 1 1 1 1 1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 16 DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 1 2119640-1 1 2079988_GATD 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-1 1 2079764 1 2119083 2 2168400-6 260 252 250 249 248 247 246 245 244 243 242 240 ITEM NO 1 1 1 Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 1 - 1 1 1 1 - A 1 1 1 1 1 1 1 1 REF - - 1 1 2 1 1 1 1 1 1 2 1 3 2 1 1 4 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - - 66 P LTR - 1 1 1 1 1 1 2 1 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 1 1 1 1 -6 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 4 1 - 1 1 4 - - 1 1 4 - 1 1 - - 1 1 1 4 2 1 - - 3 2 1 1 1 3 2 - 2 1 3 1 1 2 1 2 1 1 2 - 1 1 - - 1 1 1 2 1 1 1 - 1 1 1 1 2 1 1 1 1 2 1 1 - 1 2 1 1 - 1 1 - 1 REF REF 2 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 -5 -2 mm MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - GH TE B ECR-15-004376 14APR2015 YY UG C ECR-17-011047 31JUL2017 MZ KZ C1 ECR-19-002643 19FEB2019 TB CT MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPRING, COMPRESSION FEED FINGER ASSEMBLY,SF FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE PNT, M3 x 4.0 SCR, SET, FLT PNT, M5 X 20.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 WASHER, FLAT, REG M4 SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 30MAR2014 CHK 31MAR2014 APVD 31MAR2014 HOFFNER T.ELBIN T.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119740-2 .. 1 1901094-3 1 1803237 1 1-5018030-0 1 1-1752354-2 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 SIMP_1-22281-8 1 2119944-1 1 1-690438-0 2 2168083-1 1 2168083-6 1 2-455888-1 1 SIMP_1962431-2 1 854769-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 2 2-18032-5 1 2079383-4 1 5-18022-5 1 21028-2 1 1338685-1 4 2168400-1 3 18023-9 1 2119652 1 2119653 1 2-2119656-1 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 1-2119644-4 1 2119085_PRE_REV_K 1 2119092-1 1 2-1752356-6 2 2079383-5 1 2161328 1 1320908-2 1 2-1901086-0 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-1 1 1320928-2 1 980371-4 1 1-18028-2 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-1 1 8-1633927-1 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-3 1 3-238011-6 1 1803167-1 1 455888-4 1 1-1633713-4 239 238 213 198 182 181 180 177 176 175 174 172 166 164 163 137 136 135 133 121 117 96 95 93 82 77 74 71 67 66 63 62 61 60 59 58 56 54 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 27 26 25 24 23 20 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2063440-1 TE Connectivity APPLICATION SPEC - 1 2119580-1 DESCRIPTION PRODUCT SPEC - APVD 11JUN2014 PART NO - DWN RELEASED -1 1 DATE A 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 - - DESCRIPTION 2119580-1 2063440-1 2119740-2 1901094-3 1803237-1 1-5018030-0 1-1752354-2 993111-1 5-22280-0 1752353-3 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-22281-8 2119944-1 1-690438-0 2168083-1 2168083-6 2-455888-1 1962431-2 854769-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2-18032-5 2079383-4 5-18022-5 21028-2 1338685-1 2168400-1 18023-9 2119652-1 2119653-1 2-2119656-1 2119370-1 2079383-7 2119645-1 2119957-1 1-2119644-4 2119085-1 2119092-1 2-1752356-6 2079383-5 2161328-1 1320908-2 2-1901086-0 455888-3 22283-1 356835-1 240792-1 1320928-2 980371-4 1-18028-2 3-22280-3 1-356885-4 2119805-1 1633861-1 8-1633927-1 2119780-3 3-238011-6 1803167-1 455888-4 1-1633713-4 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) - -77 -7 ATLANTIC VERSION AMP 4805 REV 31MAR2000 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 REVISIONS DIST FEED TYPE - 2266237 -2 LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 1 Ocean Side Feed Applicator - DRAWING NO 2266237 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV C1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL 6 6 A D - - - 62 247 246 39 56 2 260 44 7 252 245 35 244 7 249 63 A APVD 37 38 59 250 DWN 40 239 PNEUMATIC DATE 238 D 2 2 2 2 243 166 8 242 2 6 0.0 163 8 59 82 177 136 1 REF 1 34 REF 137 C C 2 172 2 176 56 SERVO LATCH PLATE 240 2 2 TERMINAL SUPPORT LOCATION 1 174 4 175 28 5 41 181 133 4 135 182 198 6 A SERVO FEEDER NOT INCLUDED 66 2 67 11 213 77 A 30 117 REF 180 164 33 24 B 3 58 10 B 74 95 96 9 1 ITEM 30 LOCATED AT FRONT HOLES 12 29 CAM POSITIONS 47 29 REF 25 11 30mm STROKE 30mm STROKE 30mm STROKE 20 27 61 26 23 121 93 32 46 34 54 8 1 60 54 10 1 248 48 30 REF FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30MAR2014 CHK 31MAR2014 APVD 31MAR2014 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266237 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV C1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 6 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2266237 -1 C FINE CRIMP HEIGHT ADJUST MECHANICAL D C FINE CRIMP HEIGHT ADJUST OBSOLETE PNEUMATIC 2- 2266237 -5 C FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 2- 2266237 -7 C FINE CRIMP HEIGHT ADJUST NONE 7- 2266237 -7 A CRIMP TOOLING KIT - - OBSOLETE - 6 4 OBSOLETE - OBSOLETE - - CRIMP WIRE INSUL APPLICATOR DATA SIZE - - TYPE - F F 0.66 mm [.026] 0.69 mm [.027] APPLICATOR INSTRUCTIONS 408-10389 - JST TERMINAL TERMINAL DATA: JST CRIMP SPECIFICATION WIRE STRIP LENGTH 0.80-1.50 mm [.031-.059 IN] C - AMP MCP 2.8K FLAT TYPE RECEPTACLE TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION n CHM-1-165 - - INSULATION DIAMETER RANGE - 0.53-0.77 mm [.021-.030 IN] - - - - - TERMINALS APPLIED TE TERMINAL 2113441-1 JST TERMINAL C1__DWG_PN_1_0 SSHL-003T-PO.2 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_3_0 2113441-2 C1__DWG_PN_3_1 JST TERMINAL - C1__DWG_PN_4_0 SSHL-003GA1-P0.2 - C1__DWG_PN_4_1 - WIRE SIZE 28 AWG 30 AWG 32 AWG CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.45+/-0.02 [.018+/-.001] 0.42+/-0.02 [.017+/-.001] 0.40+/-0.02 [.016+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 - 9 7.5 7.9 8.2 - 6 W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - 1 B 2 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2266237 -4 2266237 -4 2266237 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 A 11 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 - & 62. - & 152. - MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. THIS APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER TERMINATING UNIT. 6 - 1 1 1 1 1 - 1 1 1 1 1 2 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - -77 -27 -25 -22 -21 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-1 2079764-1 2119083-1 2168400-6 2119580-1 2063440-1 PART NO FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE DESCRIPTION 1 2119782 1 2119640-1 1 2079988_GATD 1 1-22279-3_SIMP 1 2119082-1 1 2079764 1 2119083 2 2168400-6 1 2119580-1 1 2063440-1 Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 - 1 251 250 249 246 244 243 242 240 239 238 - 1 1 1 - A 66 1 1 1 1 - 1 - - P LTR 1 1 - 1 1 1 1 1 2 1 REF 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 - 1 1 REF REF REF - - 1 1 1 - - 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 - - 2 1 1 - 3 2 - 1 1 3 2 - 2 1 3 2 1 2 1 3 1 1 2 1 1 1 - 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 - 1 2 1 1 - 1 2 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 1 mm MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DESCRIPTION DWN 30MAR2014 CHK 31MAR2014 APVD 31MAR2014 T.ELBIN T.ELBIN NAME A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 1803237 1 1-5018030-0 1 1-1752354-2 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 2-2119656-2 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 SIMP_1-22281-8 1 2119944-1 1 1-690438-0 2 2168083-1 1 2168083-6 1 2-455888-1 1 SIMP_1962431-2 1 854769-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 2 2-18032-5 1 5-18022-5 1 21028-2 1 1338685-1 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 1-2119644-4 1 2-1752356-6 2 2079383-5 1 2161328 1 1320908-2 1 2-1901086-0 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-1 1 1320928-2 1 980371-4 1 1-18028-2 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-1 1 8-1633927-1 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-3 1 3-238011-6 1 1803167-1 1 455888-4 1 1-1633713-4 213 198 182 181 180 177 176 175 174 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 121 117 96 95 93 82 77 74 71 67 66 63 62 61 59 58 56 49 48 41 40 39 38 34 33 32 30 29 28 27 26 25 24 23 20 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 SIZE - .. 1 1901094-3 TE Connectivity - WEIGHT - 1 2119740-2 DESCRIPTION APPLICATION SPEC - APVD - TAG,IDENTIFICATION SPACER, FEEDER STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPRING, COMPRESSION FEED FINGER ASSEMBLY,SF FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE PNT, M3 x 4.0 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 WASHER, FLAT, REG M4 SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM PRODUCT SPEC - DWN - PART NO HOFFNER DATE SEE SHEET 1 2119740-2 1901094-3 1803237-1 1-5018030-0 1-1752354-2 993111-1 5-22280-0 1752353-3 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 2-2119656-2 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-22281-8 2119944-1 1-690438-0 2168083-1 2168083-6 2-455888-1 1962431-2 854769-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2-18032-5 5-18022-5 21028-2 1338685-1 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 1-2119644-4 2-1752356-6 2079383-5 2161328-1 1320908-2 2-1901086-0 455888-3 22283-1 356835-1 240792-1 1320928-2 980371-4 1-18028-2 3-22280-3 1-356885-4 2119805-1 1633861-1 8-1633927-1 2119780-3 3-238011-6 1803167-1 455888-4 1-1633713-4 - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 2 of 4) - -77 -27 -25 -22 -21 ITEM NO PACIFIC VERSION AMP 4805 REV 31MAR2000 REVISIONS DIST - - 2- 2266237 -2 LOC 1 Ocean Side Feed Applicator - DRAWING NO 2266237 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE - - - 40 145 38 239 246 39 59 140 152 7 56 2 D 2 2 244 7 139 243 PNEUMATIC 250 2 8 63 249 166 242 2 6 238 A 163 34 59 82 177 1 137 C 2 56 2 SERVO LATCH PLATE 2 2 133 4 176 198 182 A A 30 SERVO FEEDER NOT INCLUDED 41 66 2 67 77 213 58 10 95 117 REF 4 5 11 24 1 28 6 180 33 3 175 181 164 C 174 135 9 96 74 B 1 12 ITEM 30 LOCATED AT FRONT HOLES 29 25 CAM POSITIONS REF 30 29 REF 30mm STROKE 30mm STROKE 142 REF TERMINAL SUPPORT LOCATION 1 172 240 0.0 REF 8 136 30mm STROKE APVD 62 6 A B DWN 251 MECHANICAL D DATE 27 151 61 26 23 121 93 32 141 34 143 8 1 144 143 10 1 20 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30MAR2014 CHK 31MAR2014 APVD 31MAR2014 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266237 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C1