2266365-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 6 5 4 3 2 20 PART NUMBER REVISION DESCRIPTION FEED TYPE 2266365 -1 A FINE CRIMP HEIGHT ADJUST MECHANICAL A 2266365 -5 D FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST 2266365 -6 A NON-CRIMP HEIGHT ADJUST 2266365 -7 A FINE CRIMP HEIGHT ADJUST 7- 2266365 -7 A 4 SUPERSEDED BY 5-2266346-1 - CRIMP TOOLING KIT - - SUPERSEDED BY 5-2266346-2 - 4 SERVO LATCH PLATE 12 NONE - OBSOLETE - OBSOLETE - OBSOLETE 6 - CRIMP WIRE INSUL APPLICATOR DATA SIZE - TYPE - F F 1.17 mm [.046] 1.40 mm [.055] APPLICATOR INSTRUCTIONS 408-10389 - - - - MOLEX TERMINAL TERMINAL DATA: MOLEX CRIMP SPECIFICATION WIRE STRIP LENGTH n 1.30-1.80 mm [.051-.071 IN] C - 2.0 WIRE TO BOARD CONN CRIMP RECEPTACLE TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION 63862-8000 Rev B - - INSULATION DIAMETER RANGE - 0.95-1.40 mm [.037-.055 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 2113486-1 2113486-2 MOLEX TERMINAL 560085-0101 C1__DWG_PN_1_0 C1__DWG_PN_1_1 50372-8000 C1__DWG_PN_1_2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 2113486-3 C1__DWG_PN_3_0 C1__DWG_PN_3_1 - MOLEX TERMINAL 56161-8081 - C1__DWG_PN_4_0 6 C1__DWG_PN_4_1 C1__DWG_PN_2_2 - WIRE SIZE 22 AWG OR 0.35mm2 24 AWG OR 0.20mm2 26 AWG OR 0.12mm2 B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.725+/-0.025 [.029+/-.001] 0.645+/-0.025 [.025+/-.001] 0.595+/-0.025 [.023+/-.001] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY CRIMP HEIGHT REFERENCE SETTING - W1__FA_SETTING_2 7.1 W1__DWG_CRIMP_HT_3 W1__FA_SETTING_1 6.4 W1__DWG_CRIMP_HT_2 - 9 5.7 W1__DWG_CRIMP_HT_1 - W1__FA_SETTING_3 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 7 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2266365 2266365 2266365 2266365 - -4 -4 -5 -6 - 8 9 10 11 A 12 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37. GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 1 & 252. 1 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 13. THIS APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER SEAL TERMINATING UNIT. 1 - TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF - - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 1 1 1 1 - 1 1 1 1 1 1 1 - 1 REF 1 1 1 1 1 2 1 3 1 1 4 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 -77 -7 1 - - - 5.08 . 66 P LTR 1 - 1 - - - - 2 1 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 - 1 - 1 -6 1 1 1 1 - 1 1 - - - 1 1 1 - - 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 4 1 - 1 1 4 - - 1 1 4 - 1 1 - - 1 1 1 4 3 1 - - 1 3 1 1 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - 1 1 1 2 1 1 1 - - 1 1 1 - - 1 1 - - REF REF 1 - - 1 1 - 1 REF REF 1 - - 1 -5 -2 DIMENSIONS: ATLANTIC VERSION mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - TE ECR-18-015130 22SEP2018 TB TE APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM FEED FINGER ASSEMBLY,SF SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE PNT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM CRIMPER, WIRE DWN 25JUN2014 CHK 25JUN2014 APVD 25JUN2014 K.HUANG L.ZHANG U.GUO NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119640-1 1 2079988_GATD 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-5 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1_OLD 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 2119944-1 1 455888-5 1 SIMP_1962431-2 1 854769-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 21028-2 1 1338685-1 4 2168400-1 3 18023-9 1 2119652 1 2119653 1 2-2119656-1 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 1-2119644-4 1 2119085_PRE_REV_K 1 2119092-1 1 3-1752356-9 2 2079383-5 1 2161328 1 1320908-2 1 2119959-1 1 455888-3 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533-3 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-1 1 6-1633932-5 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-9 1 1-238011-7 1 2-1633962-8 .. 1 ITEM_2 1 4-1633860-2 260 252 250 249 248 247 246 245 244 243 242 241 240 239 238 213 198 172 166 164 163 137 136 135 133 117 82 77 74 71 67 66 63 62 60 59 58 56 54 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 8-21084-0_GATD TE Connectivity APPLICATION SPEC - 1 2119957-2 DESCRIPTION PRODUCT SPEC - APVD KH PART NO - DWN 21AUG2014 -1 - DATE RELEASED 1 - - - 1 - - 1 - 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 1 - 1 1 - - 1 - - 1 1 DESCRIPTION 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-5 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 2119944-1 455888-5 1962431-2 854769-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 21028-2 1338685-1 2168400-1 18023-9 2119652-1 2119653-1 2-2119656-1 2119370-1 2079383-7 2119645-1 2119957-1 1-2119644-4 2119085-1 2119092-1 3-1752356-9 2079383-5 2161328-1 1320908-2 2119959-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-3 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-1 6-1633932-5 2119780-9 1-238011-7 2-1633962-8 4-1633860-2 - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 A A1 PNEUMATIC SERVO LATCH PLATE REVISIONS DIST A - 2266365 -2 LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 1 Ocean Side Feed Applicator - DRAWING NO 2266365 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL 6 6 A D - - - 62 247 246 39 56 2 260 44 7 252 245 35 244 7 249 63 A APVD 37 38 59 PNEUMATIC DWN 40 239 250 DATE 238 D 2 2 2 2 243 166 8 242 2 6 163 8 59 82 1 136 REF 2.28 0.50 [ 0.090 0.019 ] 1 34 REF 137 C C 172 3 56 TERMINAL SUPPORT LOCATION 1 4 SERVO LATCH PLATE 240 133 4 5 41 135 198 66 A 2 164 33 24 SERVO FEEDER NOT INCLUDED B 28 67 11 213 A 58 74 19 10 30 117 REF 77 B 20 21 9 29 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 13 47 1 11 11 30mm STROKE 30mm STROKE 30mm STROKE 30 REF 29 REF 20 46 32 34 54 8 1 60 54 10 1 248 48 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 25JUN2014 CHK 25JUN2014 APVD 25JUN2014 K.HUANG L.ZHANG U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266365 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2266365 -1 A FINE CRIMP HEIGHT ADJUST MECHANICAL 2- 2266365 -2 D 6 A FINE CRIMP HEIGHT ADJUST 2- 2266365 -5 A FINE CRIMP HEIGHT ADJUST 2- 2266365 -7 A FINE CRIMP HEIGHT ADJUST NONE 7- 2266365 -7 A CRIMP TOOLING KIT - CRIMP WIRE INSUL SIZE - OBSOLETE - 4 - OBSOLETE - OBSOLETE - 6 - TYPE - F F 1.17 mm [.046] 1.40 mm [.055] APPLICATOR INSTRUCTIONS 408-10389 - - - MOLEX TERMINAL TERMINAL DATA: MOLEX CRIMP SPECIFICATION WIRE STRIP LENGTH n 1.30-1.80 mm [.051-.071 IN] C - 2.0 WIRE TO BOARD CONN CRIMP RECEPTACLE TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION 63862-8000 Rev B - - INSULATION DIAMETER RANGE - 0.95-1.40 mm [.037-.055 IN] - - - - - TERMINALS APPLIED TE TERMINAL 2113486-1 2113486-2 - MOLEX TERMINAL C1__DWG_PN_1_0 560085-0101 50372-8000 C1__DWG_PN_1_1 C1__DWG_PN_1_2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL C1__DWG_PN_3_0 2113486-3 MOLEX TERMINAL C1__DWG_PN_3_1 - C1__DWG_PN_4_0 56161-8081 - C1__DWG_PN_4_1 - C1__DWG_PN_2_2 - WIRE SIZE 22 AWG OR 0.35mm2 24 AWG OR 0.20mm2 26 AWG OR 0.12mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.725+/-0.025 [.029+/-.001] 0.645+/-0.025 [.025+/-.001] 0.595+/-0.025 [.023+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 5.7 6.4 7.1 - 9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 6 W1__FA_SETTING_3 - 1 B 2 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2266365 -4 2266365 -4 2266365 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 A 11 - 1 & 152. - 1 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 12. THIS APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER SEAL TERMINATING UNIT. - MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 66 P 1 1 1 1 - 1 1 - 1 LTR DESCRIPTION DATE SEE SHEET 1 - - 1 - 1 1 - 2 1 REF - - - 1 - - 1 - 1 1 1 - - - - - 1 - - - 1 1 2 - 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-5 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 2-2119656-2 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 2119944-1 455888-5 1962431-2 854769-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 21028-2 1338685-1 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 1-2119644-4 3-1752356-9 2079383-5 2161328-1 1320908-2 2119959-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-3 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-1 6-1633932-5 2119780-9 1-238011-7 2-1633962-8 4-1633860-2 1 - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 - 1 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 - - 3 1 1 - 1 3 - 1 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 - - REF 1 - - 1 - - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 - 1 - 1 1 DWN APVD - - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM FEED FINGER ASSEMBLY,SF SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE PNT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM CRIMPER, WIRE PART NO -77 -27 -25 -22 -21 Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 - 1 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 A - OBSOLETE - APPLICATOR DATA REVISIONS DIST - PNEUMATIC SERVO LATCH PLATE LOC 1 DWN 25JUN2014 CHK 25JUN2014 APVD 25JUN2014 K.HUANG L.ZHANG U.GUO NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 1-22279-3_SIMP 1 2119082-5 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1_OLD 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 2-2119656-2 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 2119944-1 1 455888-5 1 SIMP_1962431-2 1 854769-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 21028-2 1 1338685-1 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 1-2119644-4 1 3-1752356-9 2 2079383-5 1 2161328 1 1320908-2 1 2119959-1 1 455888-3 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533-3 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-1 1 6-1633932-5 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-9 1 1-238011-7 1 2-1633962-8 .. 1 ITEM_2 1 4-1633860-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079988_GATD 251 250 249 246 244 243 242 241 240 239 238 213 198 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 117 82 77 74 71 67 66 63 62 59 58 56 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119640-1 DESCRIPTION PRODUCT SPEC - 1 2119782 Ocean Side Feed Applicator - DRAWING NO 2266365 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE DWN APVD - - - 251 MECHANICAL 62 6 40 A D DATE 145 38 239 246 39 59 152 7 56 140 2 D 2 2 244 7 139 243 PNEUMATIC 250 2 8 63 249 166 242 2 6 238 A 8 2.28 0.50 [ 0.090 0.019 ] REF 163 34 59 82 136 1 137 C 1 REF TERMINAL SUPPORT LOCATION C 172 3 56 1 4 SERVO LATCH PLATE 28 41 240 133 4 135 198 164 66 2 11 A 67 33 SERVO FEEDER NOT INCLUDED 58 19 74 20 10 30 77 213 A 24 B 5 9 21 117 REF B 1 12 29 241 13 1 ITEM 30 LOCATED AT FRONT HOLES 11 30 CAM POSITIONS 30mm STROKE REF 29 30mm STROKE 30mm STROKE 142 REF 141 151 32 34 143 8 1 144 143 10 1 20 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 25JUN2014 CHK 25JUN2014 APVD 25JUN2014 K.HUANG L.ZHANG U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266365 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A1