2266535-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION REVISION 2266535 -2 C 7-2266535-2 C 7- 2266535 -7 A 5 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. PART NUMBER 6 DESCRIPTION FEED TYPE FINE CRIMP HEIGHT ADJUST REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD A RELEASED 07JAN2015 MR TE B ECR-18-015356 26SEP2018 JAH CT C ECR-19-009012 08JUN2019 TB TE PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 2.03 mm [.080] 6.35 mm [.250] APPLICATOR INSTRUCTIONS 408-35042 - 1 - 1 - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION TAB 5.8 X 0.8 TERMINAL NAME: WIRE STRIP LENGTH 4.55-5.31 mm [.179-.209 IN] C TERMINAL APPLICATION SPECIFICATION 114-18052 - TERMINALS APPLIED TE TERMINAL 2-962917-2 1-962917-2 n C1__DWG_PN_1_1 - - - C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE SEAL 963243-1 C1__DWG_PN_3_0 TE SEAL C1__DWG_PN_4_0 1 - 1.00mm2 0.75mm2 0.50mm2 1 2 B 3 4 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.56+/-0.05 [.061+/-.002] 1.47+/-0.05 [.058+/-.002] 1.38+/-0.05 [.054+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 5.2 6.2 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 6 THIS APPLICATOR APPLIES TERMINAL WITH A SEAL. 2 2 2 1 1 1 - 1 1 - 1 1 - 1 2 - 2 1 - 1 1 - 1 1 - 1 1 1 1 - 1 1 1 2 - 1 - - - - - - 1 - 1 1 1 2 - A 1 2 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - 2 1 - 1 4 2 - 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 4 - 1 1 1 - AP PLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 2 1 - W1__FA_SETTING_3 1 2 - 7 W1__FA_SETTING_2 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 5 7 4.4 1 1 W1__FA_SETTING_1 1 1 - 4 1 1 - CRIMP HEIGHT REFERENCE SETTING 2 1 - CRIMP HEIGHT mm [INCH] 1 2 - WIRE SIZE 1 1 - C1__DWG_PN_2_2 1 1 - C1__DWG_PN_3_1 1 1 - CABLE DIAMETER 1 REF REF - 6 1 1 - - 1 1 - 5 1-962917-1 C1__DWG_PN_1_2 - TE TERMINAL 2-962917-1 C1__DWG_PN_1_0 6 1 1 - INSULATION DIAMETER RANGE 1 1 - 3 1 1 - 1803078-3 2119641-1 2119082-4 2079764-1 2119083-1 7-18023-7 2844940-1 994970-2 455888-2 2844908-1 2844907-1 455888-5 2079383-4 1803096-1 1803607-3 2119791-9 2119943-1 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338683-8 2168083-3 1-2168083-0 5018030-1 1-811242-0 690753-2 18023-9 1803583-9 1803515-2 1803602-2 1-1752356-2 2079383-5 2-2844962-3 2844992-2 455888-3 1320928-6 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1-318707-2 7-1803054-2 2-2119781-4 238011-9 5-1803018-0 1-455888-5 5-456405-6 1 1 1 1 2 1 -77 -72 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - SPACER, PRECISION FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 AIR FEED MODULE COUNTER, MAGNETIC SPACER, CRIMPER SCREW, LOCKING POST, LOCKING SPACER, CRIMPER SCR, BHSC, RoHS (M4 X 8) EXTENSION PLATE DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 40) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO DWN 21OTC2014 CHK 21OTC2014 APVD 21OTC2014 J.HOU Y.YIN U.GUO NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2079764 1 2119083 1 7-18023-7 1 2844940-1 1 COUNTER_994970 1 455888-2 1 2844908 1 2844907 1 455888-5 2 2079383-4 1 1803096-1 1 1803607_3 1 2119791-9 1 2119943-1 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338683-8 4 2168083-3 2 1-2168083-0 1 5018030-1 1 1-811242-0 1 690753-2 1 18023-9 1 1803583-9 1 1803515-2 1 1803602-2 1 1-1752356-2 2 2079383-5 2 2-2844962-3 1 2844992-2 1 455888-3 1 1320928-6 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1-318707-2 1 7-1803054-2 .. 1 ITEM_7 .. 1 ITEM_6 1 2-2119781-4 1 238011-9 1 5-1803018-0 1 1-455888-5 1 5-456405-6 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119082-4 259 248 244 243 242 241 238 164 120 99 98 82 79 78 71 70 69 67 66 60 59 57 56 54 53 52 51 50 49 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC - 1 1803078-3 Ocean Side Feed Applicator - DRAWING NO 2266535 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION SEE SHEET 1 - DWN APVD - - - REF 5 D DATE D FEED TYPE 44 PNEUMATIC 2.2 REF 2 57 REF SHEAR DEPRESSOR DETAIL 244 53 A 238 243 242 50 C SEE DETAIL A 82 1 1 120 70 69 2 3 51 1 4 28 5 41 44 REF 0.05 66 2 33 67 164 24 57 A RAM SET-UP 7 19 B B 20 79 21 78 9 29 1 ITEM 30 LOCATED AT REAR HOLES 12 241 CAM POSITION 30mm STROKE 0.5 TERMINAL SUPPORT LOCATION 44.25 30 5.1 C FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) DETAIL A REF 34 REF 52 56 3 8 259 59 2 13 30 REF 29 REF 1 11 20 46 98 99 34 54 8 1 60 54 10 1 248 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 21OTC2014 CHK 21OTC2014 APVD 21OTC2014 J.HOU Y.YIN U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266535 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV C 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2266535 -2 C FINE CRIMP HEIGHT ADJUST PNEUMATIC 7- 2266535 -7 A CRIMP TOOLING KIT - REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - D D APPLICATOR DATA CRIMP SIZE WIRE INSUL TYPE F O 2.03 mm [.080] 6.35 mm [.250] APPLICATOR INSTRUCTIONS 408-35042 - TE TERMINAL TERMINAL DATA: TAB 5.8 X 0.8 TERMINAL NAME: WIRE STRIP LENGTH 4.55-5.31 mm [.179-.209 IN] C TERMINAL APPLICATION SPECIFICATION 2-962917-2 1-962917-2 114-18052 - TERMINALS APPLIED TE TERMINAL n 2-962917-1 1-962917-1 C1__DWG_PN_1_1 C1__DWG_PN_1_2 C1__DWG_PN_2_1 TE SEAL 963243-1 TE SEAL 1 - REF - 1 - 1 - - C1__DWG_PN_3_0 1 - 4 - 5 C1__DWG_PN_2_0 1 - - - TE TERMINAL C1__DWG_PN_1_0 - 1 - 3 INSULATION DIAMETER RANGE 6 1 - TE CRIMP SPECIFICATION 1 - CABLE DIAMETER C1__DWG_PN_4_0 1 - 6 1 - C1__DWG_PN_3_1 1 - C1__DWG_PN_2_2 1 - 1 - WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.56+/-0.05 [.061+/-.002] 1.47+/-0.05 [.058+/-.002] 1.38+/-0.05 [.054+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 4.4 5.2 6.2 2 - CRIMP HEIGHT 4 REFERENCE SETTING 1 - 1 - 1 - W1__FA_SETTING_1 1 - W1__FA_SETTING_2 1 - W1__FA_SETTING_3 2 - 1 2 B 3 4 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 6 THIS APPLICATOR APPLIES TERMINAL WITH A SEAL. 1 - 2 - 1 - 1 - 1 - 1 - 1 - 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 5 7 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 - 7 2 - 2 - 1 - 1 - 1 - 1 - AP PLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 2 - 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 - 1 1 - 1 1 - 1 1 1 1 - 1 1 1 - - - - - 1 1 1 1 1 1 1 - A 1803078-3 2119082-4 2079764-1 2119083-1 7-18023-7 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 1-1803583-0 1803516-2 455888-2 2844908-1 2844907-1 455888-5 2079383-4 1803096-1 1803607-3 2119791-9 2119943-1 2119740-1 2168078-1 5-18022-5 985575-3 1338683-8 1-2168083-0 5018030-1 1-811242-0 690753-2 18023-9 1803602-2 1-1752356-2 2079383-5 2-2844962-3 2844992-2 455888-3 1320928-6 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1-318707-2 7-1803054-2 2-2119781-4 238011-9 5-1803018-0 1-455888-5 5-456405-6 1 1 1 PART NO -77 -22 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - SPACER, PRECISION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC SPACER, CRIMPER SCREW, LOCKING POST, LOCKING SPACER, CRIMPER SCR, BHSC, RoHS (M4 X 8) EXTENSION PLATE DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 SCR, BHSC, RoHS (M8 X 40) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 21OTC2014 CHK 21OTC2014 APVD 21OTC2014 J.HOU Y.YIN U.GUO NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 1-1803583-0 1 1803516-2 1 455888-2 1 2844908 1 2844907 1 455888-5 2 2079383-4 1 1803096-1 1 1803607_3 1 2119791-9 1 2119943-1 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338683-8 2 1-2168083-0 1 5018030-1 1 1-811242-0 1 690753-2 1 18023-9 1 1803602-2 1 1-1752356-2 2 2079383-5 2 2-2844962-3 1 2844992-2 1 455888-3 1 1320928-6 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1-318707-2 1 7-1803054-2 .. 1 ITEM_7 .. 1 ITEM_6 1 2-2119781-4 1 238011-9 1 5-1803018-0 1 1-455888-5 1 5-456405-6 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764 259 244 243 242 241 238 164 151 144 143 141 140 120 99 98 82 79 78 71 70 69 67 66 59 57 56 53 52 51 50 49 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-4 DESCRIPTION PRODUCT SPEC - 1 1803078-3 Ocean Side Feed Applicator - DRAWING NO 2266535 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - 140 FEED TYPE 2 REF D 57 243 53 A 242 REF SHEAR DEPRESSOR DETAIL 2 3 50 238 5.1 REF 8 82 52 C SEE DETAIL A 56 1 REF TERMINAL SUPPORT LOCATION 1 120 C 70 69 51 2 3 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 1 4 28 5 140 41 35.22 REF 0.05 66 164 2 DETAIL A 0.5 34 59 259 - 2.2 REF 244 PNEUMATIC APVD - - 5 D DWN 67 33 19 A 24 20 7 RAM SET-UP 21 30 B 57 B 79 9 78 1 12 29 241 13 CAM POSITION ITEM 30 LOCATED AT REAR HOLES 1 30 REF REF 29 30mm STROKE 151 141 98 99 34 143 8 1 144 143 10 1 20 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 AIR FEED PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 21OTC2014 CHK 21OTC2014 APVD 21OTC2014 J.HOU Y.YIN U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266535 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C