2266768-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION 4 3 2 LOC DESCRIPTION C FINE CRIMP HEIGHT ADJUST MECHANICAL 5-2266768-1 C SEAL STRIPPER CRIMPER TERMINATING UNIT MECHANICAL 5-2266768-2 C 7-2266768-1 C 7-2266768-2 C 7- 2266768 -7 A FINE CRIMP HEIGHT ADJUST PNEUMATIC AND CRIMP TOOLING KIT APPLICATOR INSTRUCTIONS 408-35042 - - 1 - 1 - TYPE 1 - 3 1 - 1 - - - 1 - MOLEX TERMINAL MX 150 BLADE CABLE SEAL TERMINAL NAME: WIRE STRIP LENGTH n 4.70-5.60 mm [.185-.220 IN] C TERMINAL APPLICATION SPECIFICATION ATS-639017300 Rev B - TERMINALS APPLIED TE TERMINAL 2113007-1 2113007-2 2113007-3 C1__DWG_PN_1_1 340801104 C1__DWG_PN_1_2 340801204 C1__DWG_PN_1_3 3 MOLEX CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - - - - - - - - - - - - 7 - - C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 TE SEAL 2113681-1 C1__DWG_PN_3_0 C1__DWG_PN_3_1 2113614-1 C1__DWG_PN_3_2 QSR SEAL E-1644-00 C1__DWG_PN_4_0 1 - 1 1 - CABLE DIAMETER 1 - 1 - C1__DWG_PN_4_1 E-1644-01 1 - 2 - C1__DWG_PN_2_3 1 - WIRE SIZE 1.00mm2 0.75mm2 18 AWG 20 AWG CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 1.30+/-0.05 [.051+/-.002] 1.25+/-0.05 [.049+/-.002] 1.25+/-0.05 [.049+/-.002] 1.15+/-0.05 [.045+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 5.1 5.6 5.6 6.7 5 4 1 - 1 - 1 - W1__FA_SETTING_1 4 - W1__FA_SETTING_2 2 - W1__FA_SETTING_3 1 - W1__FA_SETTING_4 1 - 1 - 1 - - - - 1 2 B 3 4 5 1 - 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 - 2 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242 2 - 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 - 1 - 1 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 - 2 1 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 1 - RECOMMENDED SPARE PARTS 1 - 1 - 1 - TERMINAL LUBRICANT IS RECOMMENDED. 1 - 1 1 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 1 2 - 1 - - - 1 - A 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 - - 1 1 1 1 20MAY2015 KH GB A1 ECR-15-010123 07JUL2015 YY CT B ECR-19-014096 10SEP2019 LG TE C ECR-22-136626 21APR2022 FJ GB 1 2 - Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 1 2 DIMENSIONS: mm & 4 of 4) MATERIAL PART NO - - - 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 2 1 1 1 1 1 1 2 2 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 - 1 1 1 1 - 1 1 - 1 1 1 1 - 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 - 1 1 - - - 2 - 1 - 1 1 1 - 1 1 2 - 1 1 1 1 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. ATLANTIC VERSION -1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 - -77 -72 -71 -52 -51 -2 AMP 4805 REV 31MAR2000 APVD RELEASED 1803515-3 2-1803583-1 2119641-1 2119082-3 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 4-1722335-3 1-5018030-0 1-1752354-9 993111-1 5-22280-0 1752353-3 1901680-2 994970-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 1-2168083-0 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 3-1752356-4 2079383-5 3-2844962-0 2844992-4 455888-3 240792-1 1320928-6 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 4-1803171-2 3-240641-8 2-2119781-4 238011-4 7-1803018-0 455888-9 6-1490019-2 - REF REF REF REF REF REF - 7 MOLEX TERMINAL 340801002 C1__DWG_PN_1_0 DWN D - TERMINAL DATA: DATE - F O 3.50 mm [.138] DESCRIPTION PNEUMATIC CRIMP TOOLING KIT 2.07 mm [.082] LTR MECHANICAL - WIRE INSUL P PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT SIZE 66 A - CRIMP REVISIONS PNEUMATIC SEAL STRIPPER CRIMPER TERMINATING UNIT APPLICATOR DATA 1 DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE 2266768 -1 C 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2266768 -2 D 6 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - RAM ASSEMBLY, SF ATLANTIC APPLICATOR BASIC ASSEMBLY, SF FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER DRAG, TERMINAL STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 23APR2015 CHK 23APR2015 APVD 23APR2015 K.HUANG L.ZHANG U.GUO NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119082-3 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 4-1722335-3 1 1-5018030-0 1 1-1752354-9 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 1 COUNTER_994970 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 1-2168083-0 1 5018030-1 1 811242-5 1 690753-2 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 3-1752356-4 2 2079383-5 2 3-2844962-0 1 2844992-4 1 455888-3 1 240792-1 1 1320928-6 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 4-1803171-2 1 3-240641-8 .. 1 ITEM_6 1 2-2119781-4 1 238011-4 1 7-1803018-0 1 455888-9 1 6-1490019-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119641-1 293 292 248 244 243 242 241 239 238 182 181 180 177 176 175 174 164 113 99 98 82 71 67 66 60 59 57 56 54 53 52 51 50 49 48 47 46 44 41 34 33 30 29 28 25 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2-1803583-1 DESCRIPTION PRODUCT SPEC - 1 1803515-3 Ocean Side Feed Applicator - DRAWING NO 2266768 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 5 REF D 59 56 44 PNEUMATIC 293 2.0 REF 2 57 REF SHEAR DEPRESSOR DETAIL 244 243 A 53 238 242 2 3 50 59 C 8 7 82 1 REF 3.2 1 0.5 34 REF 52 SEE DETAIL A 2 51 C 3 177 56 TERMINAL SUPPORT LOCATION 1 4 2 176 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 2 28 5 41 174 44 293 175 44.58 181 182 DETAIL A 164 33 0.05 66 180 2 67 A 24 B 3 REF 57 19.0 5 180 REF RAM AND HOLD DOWN SET-UP 19 30 0.5 B 20 21 29 9 1 ITEM 30 LOCATED AT REAR HOLES 12 25 CAM POSITIONS 13 47 1 11 30mm STROKE 30mm STROKE 30mm STROKE 30 REF 29 REF 241 113 7 46 292 98 99 34 54 8 1 60 54 10 20 1 248 48 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 23APR2015 CHK 23APR2015 APVD 23APR2015 K.HUANG L.ZHANG U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266768 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV C 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2266768 -1 C FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2266768 -7 A CRIMP TOOLING KIT - C 3 2 LOC PART NUMBER 2- 2266768 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 2.07 mm [.082] 3.50 mm [.138] APPLICATOR INSTRUCTIONS 408-35042 - MOLEX TERMINAL TERMINAL DATA: MX 150 BLADE CABLE SEAL TERMINAL NAME: WIRE STRIP LENGTH n 4.70-5.60 mm [.185-.220 IN] C TERMINAL APPLICATION SPECIFICATION ATS-639017300 Rev B - TERMINALS APPLIED TE TERMINAL 2113007-1 2113007-2 2113007-3 WIRE SIZE 1.00mm2 0.75mm2 18 AWG 20 AWG 340801002 340801104 C1__DWG_PN_1_1 C1__DWG_PN_1_2 340801204 C1__DWG_PN_1_3 - - - C1__DWG_PN_2_1 C1__DWG_PN_2_2 TE SEAL C1__DWG_PN_3_0 2113681-1 2113614-1 C1__DWG_PN_3_1 C1__DWG_PN_3_2 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 1 - CABLE DIAMETER E-1644-00 E-1644-01 1.30+/-0.05 [.051+/-.002] 1.25+/-0.05 [.049+/-.002] 1.25+/-0.05 [.049+/-.002] 1.15+/-0.05 [.045+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 5.1 5.6 5.6 6.7 - 5 7 TERMINAL LUBRICANT IS RECOMMENDED. 2 1 1 1 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 - - - 1 - A 1 2 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 2 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 2 2 - 1 1 2 - 1 1 1 - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - 1 2 - - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242 2 1 - 3 1 2 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 2 1 - 1 1 2 - B 1 1 - W1__FA_SETTING_4 1 1 5 1 1 - W1__FA_SETTING_3 1 1 - W1__FA_SETTING_2 1 1 - W1__FA_SETTING_1 1 1 - 4 1 1 - CRIMP HEIGHT REFERENCE SETTING 1 1 - 7 4 - - C1__DWG_PN_4_1 1 4 - C1__DWG_PN_4_1 - 1 - QSR SEAL - REF REF - C1__DWG_PN_4_0 1 1 - C1__DWG_PN_2_3 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 - C1__DWG_PN_4_0 1 - C1__DWG_PN_2_0 1 1 - INSULATION DIAMETER RANGE 1 1 - 1 1 1 1 - 1 1 1 1 1 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER DRAG, TERMINAL STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: 2119082-3 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 1-2168083-0 5018030-1 811242-5 690753-2 18023-9 2119652-1 1803602-1 3-1752356-4 2079383-5 3-2844962-0 2844992-4 455888-3 240792-1 1320928-6 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 4-1803171-2 3-240641-8 2-2119781-4 238011-4 7-1803018-0 455888-9 6-1490019-2 1 1 - 3 7 MOLEX TERMINAL C1__DWG_PN_1_0 - MOLEX CRIMP SPECIFICATION - 1 DWN 23APR2015 CHK 23APR2015 APVD 23APR2015 K.HUANG L.ZHANG U.GUO NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 1-2168083-0 1 5018030-1 1 811242-5 1 690753-2 3 18023-9 1 2119652 1 1803602-1 1 3-1752356-4 2 2079383-5 2 3-2844962-0 1 2844992-4 1 455888-3 1 240792-1 1 1320928-6 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 4-1803171-2 1 3-240641-8 .. 1 ITEM_6 1 2-2119781-4 1 238011-4 1 7-1803018-0 1 455888-9 1 6-1490019-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119083 244 243 242 241 239 238 164 151 144 143 142 141 140 113 99 98 82 71 67 66 59 57 56 53 52 51 50 49 48 41 34 33 30 29 28 25 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079764_APP DESCRIPTION PRODUCT SPEC - 1 2119082-3 Ocean Side Feed Applicator - DRAWING NO 2266768 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 D 2.0 REF 2 244 57 56 PNEUMATIC 243 242 A 238 2 3 3.2 34 7 82 1 REF TERMINAL SUPPORT LOCATION 1 C 52 56 0.5 REF 8 50 SEE DETAIL A REF SHEAR DEPRESSOR DETAIL 53 59 C REF 5 2 3 51 1 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 4 28 5 140 41 35.55 164 DETAIL A 67 33 B A 30 0.05 66 2 24 REF 57 5 RAM SET-UP 19 B 20 21 9 29 1 ITEM 30 LOCATED AT REAR HOLES 12 CAM POSITIONS 30mm STROKE 142 241 25 13 30mm STROKE 30 REF 29 1 REF 30mm STROKE 151 113 48 7 141 98 99 34 143 8 1 144 143 10 1 20 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 23APR2015 CHK 23APR2015 APVD 23APR2015 K.HUANG L.ZHANG U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266768 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C