2352906-1

12-Port GIGABIT MANAGED RACK MNT PoE SWITCH QUICK INSTALLATION GUIDE INTRODUCTION The 2352906 series is a managed 10G/2.5G redundant PoE Ethernet switch with 8x 10/100/1000 Base-T(X) P.S.E. and 4x 1G/2.5G/5G/10GBase-T ports, specifically designed for the toughest environment and fully compliant with EN50155. The switch supports Ethernet Redundancy protocols such as TE-Ring (recovery time < 30ms over 250 units), TE-Chain, MRP and MSTP (RSTP/STP compatible) which can protect your mission critical applications from network interruptions or temporary malfunctions. 2352906 also support Power over Ethernet, a system to transmit electrical power up to 30 watts per port, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. The series can also be managed centralized and convenient by TE-Vision, Telnet and console (CLI) configuration. PACKAGE CONTENTS The device is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance. • 2352906 series Ethernet switch • Rack monting kit (Left + Right) • CD Containing software • Quick Installation Guide PREPARATION Before you begin installing the device, make sure you have all of the package contents available and a PC with Microsoft Internet Explorer 6.0 or later, for using web-based system management tools. Safety & Warnings Elevated Operating Ambient: If installed in a closed environment, make sure the operating ambient temperature is compatible with the maximum ambient temperature (Tma) specified by the manufacturer. Reduced Air Flow: Make sure the amount of air flow required for safe operation of the equipment is not compromised during installation. Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous condition due to uneven mechanical loading. Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. DIMENSIONS (in mm) EN 50155 SWITCH 24-Port GIGABIT MANAGED PoE SWITCH QUICK INSTALLATION GUIDE WIRING PANEL LAYOUTS For pin assignments please refer to the instructions below: 32 6 7 8 12 16 Grounding Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the grounding pin on the power connector to the grounding surface prior to connecting devices. 14 15 Power port pinouts The 2352906 series uses the M12 S-coded 4-pin female connector on the front panel for the power input. 1 9 45 10 11 13 1 Reset Button 9 PoE enabled Gigabit ethernet ports 2 Power status LED 10 Link/ACT LED for PoE enabled Gigabit ports 3 R.M. Status LED 11 PoE indicator for PoE enabled Gigabit ports 4 Ring Status LED 12 Speed LED for PoE enabled Gigabit ports 5 Fault LED 13 1G/2.5G/5G/10GBase-T Ethernet ports with bypass 6 Power Connector 14 Link/ACT LED for non-PoE Gigabit ports 7 Relay output port 15 LED for 5G/2.5Gbps Ethernet speed indicator 8 Console port 16 LED for 10G/1Gbps Ethernet speed indicator Step 1: Insert a power cable to the power connector on the device. Step 2: Rotate the outer ring of the cable connector until a snug fit is achieved. Make sure the connection is tight. Console port pinout The switch has one RS-232 (M12 A-Code 5pin) console port, located on the front panel. Use a M12-to-DB9 console cable to connect the console port to your PC‘s COM port. Relay output ports pinouts The switch uses the M12 A-coded 5-pin female connector on the front panel for relay output. Use a cable with an M12 A-coded 5-pin male connector to connect the relay. The relay contacts will detect user-configured events and form an open circuit when an event is triggered. M12 X-Code Ethernet ports INSTALLATION Rack mounting Step 1: Install left and right front mounting brackets to the switch using 4 M3 screws on each sideprovided with switch. Step 2: With front brackets orientated in front of the rack, nest front and rear brackets together. Fasten together using remaining M4 screws into counter sunk holes. Step 3: Fasten the front mounting bracket to the front of the rack. Pin No. Description Pin No. Description 1 BI_DA+/Vout+ 5 BI_DD+ 2 BI_DA-/Vout+ 6 BI_DD- 3 BI_DB+/Vout- 7 BI_DC- 4 BI_DB-/Vout- 8 BI_DC+ NC Relay NC NC 24-Port GIGABIT MANAGED PoE SWITCH QUICK INSTALLATION GUIDE LED INDICATORS PoE power budget Partnumber 2352906-1 2352906-2 Input Power After installing the switch and connecting cables, the green power LED should turn on. Please refer to the following table for LED indication. PoE power budget per group 72-110VDC 60W NETWORK CONNECTION The device provides Ethernet ports in M12 connector type. According to the link type, the switchuses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers, switches,routers, or hubs). Please refer to the following table for cable specifications Pin No. Type Max Length Connector 10BASE-T Cat. 3, 4, 5 100Ω UTP 100m M12 X-Coding Connector 100BASE-T Cat. 5 100Ω UTP UTP 100m M12 X-Coding Connector 1000BASE-T Cat. 5/5e 100Ω UTP UTP 100m M12 X-Coding Connector LOGIN Default IP adress: 192.168.10.1 Default username: admin Default password: admin Refer to the user manual for further instructions RESET To restore the device configurations back to the factory defaults, press the Reset button for 5 seconds. Once the power indicator starts to flash, release the button. The device will then reboot and return to factory defaults. LED Color Status PWR Green On DC power module activated R.M Green On Device operating in Ring master mode Ring Green On Ring enabled Fault Amber Blink On Description Ring structure is broken Errors occur (i.e. power failure or port malfunction) 10/100/1000Base-T(X) P.S.E. Ethernet ports On Port is linked LNK/ACT Green PoE Green On Power supplied over Ethernet Green On Port is running at 1Gbps Amber On Port is running at 100 Mbps - Off Port is running at 10Mbps Speed Blink Transmitting data 1G/2.5G/5G/10GBase-T Ethernet ports LNK/ACT 5G/2.5G 10G/1G Green Amber On Blink On Port is linked Transmitting data Port is running at 2.5Gbps Green On Port is running at 5Gbps Amber On Port is running at 1Gbps Green On Port is running at 10Gbps Revision 1_0, 29 August 2019