2388600-1

Removable Q-Cee’s LabelsType QC, PM, MAM & MQC Technical Datasheet TTDS-249 Revision 3 – June 2023 Q-Cee Labels are a selection of popular pre-printed labels used in Inspection, Calibration, Inventory and Maintenance tasks. These kits are a selection of labels aimed at the relevant operator or worker for their daily use. These labels are a permanent label however they can be removed cleanly after use if required. The labels are all made from a vinyl base material for tough performance. Labels are supplied as individual sheets in the handy pocket sized kits as shown above. Some of the labels are designed with a write-on surface. This allows the user to add additional information e.g. date of test, operator I.D. etc. TE recommends use of a high performance, permanent marker pen with these labels. The kits come in a handy pocket size convenient booklet design with a cover to protect the labels inside. The booklet is designed to be easily stored or hung above the workshop bench. PAGE 1 INDUSTRIAL /// TTDS-249 – REMOVABLE Q-CEE’S LABELS TECHNICAL DATA SHEET Removable Q-Cee’s Labels-Type QC, PM, MAM & MQC Features Temperature Rating • Permanent adhesive but removable • Operating Temperature Range • Tough vinyl base material • Writable surface -40 to 80°C (-40°F to 176°F) • Minimum Application Temperature 10°C (50°F) • No adhesive residue on removal • Variety of label designs in the kit Applications Design for Environment • Ideal for identification of maintenance, calibration, • Does not contain any declarable or prohibited sub- stock control and inspection work. • Industrial, Automotive, Rail, Electrical, Laboratory and Warehouse. stances from the UNIFE Railway Industry Substances List • Further information and a downloadable declaration covering RoHS and REACH compliance can be found at the TE Product Compliance Support Centre: http://www.te.com/usa-en/utilities/productcompliance.html Shelf Life 2 years when following good commercial storage practice detailed below. Storage Product should be stored in the original packaging, with any plastic covers which were included during shipping. Store out of direct sunlight in a clean, dry, dust free, environment. Product should be stored at approximately 21°C and 50% relative humidity. PAGE 2 INDUSTRIAL /// TTDS-249 – REMOVABLE Q-CEE’S LABELS TECHNICAL DATA SHEET Removable Q-Cee’s Labels-Type QC, PM, MAM & MQC Typical Label Thickness • Label (including adhesive): 0.120 mm / 0.005 inch • Liner: 0.188 mm / 0.007 inch Technical Performance Requirement Results Marking of Electrical Insulating Materials, SAE AS 4952 Legible after 100 rubs 1kg weight with an eraser Pass Resistance to Solvents, MIL STD 202 Method 215 Legible after 30 wipes Pass Print Permanence Fluid Exposure • • • • • • • • Isopropyl alcohol IRM 902 reference oil Grease Engine Oil Diesel Fuel Tap water 5% Salt solution Detergent (1% solution) Adhesive/color Labels to remain on test plate, legible (TE doc 109-121012) and no change in pre-printed color Samples stuck to Aluminium plates. 24 hours immersion in fluid @ 23°C followed by 20 rubs, SAE AS5942 Adhesion to FTM1 (180°) Test surface: Pass Pass Pass Pass Pass Pass Pass Pass Printed legend Pass Pass Pass Pass Pass Pass Pass Pass Typical Peel force (N/25mm (oz/in.)) FTM1 (180°) 20min Dwell 72hr Dwell Stainless steel 20 (73) 22 (80) • Glass 27 (97) 28 (101) • Aluminium • Polypropylene • Epoxy painted surface • Weatherability Artificial weathering to ASTM G154 Thermal performance Heat Aging Thermal Cycling Labels to remain on plate, no discoloration and legible after 240hr, UVA and no discoloration 25 (90) 29 (105) 2.0 (7.5) 2.0 (7.5) 34 (126) 32 (116) Pass, samples remain legible and no discoloration Labels to remain on plate, no discol- Pass, samples remain legible and adhered oration and legible after 168hr at to test plate 100±2°C Labels to remain on plate, no discol- Pass, samples remain legible and adhered oration and legible after 10 cycles of to test plate 1hr @ -50°C then 1hr @ 90°C followed by 100rubs Note: write-on print performance is dependent on pen used. Where possible, TE have tested product as a finished item, including the print. Operational tests are followed by an assessment of mark adherence to validate fit, form and function. PAGE 3 INDUSTRIAL /// TTDS-249 – REMOVABLE Q-CEE’S LABELS TECHNICAL DATA SHEET Removable Q-Cee’s Labels-Type QC, PM, MAM & MQC Kit Label Details Label dimensions Packing Part No. Part Description No. of labels per Kit No. of labels per pack (10 Kits per bag) Label Image Label Quantity & description (w /h) mm in 50.8 x 12.7 2.0 x 0.5 105x "INVENTORY" 60x 2404300-1 INVENTORY-LABEL -BK-225 "SHELF LIFE" 225 2250 30x "SCRAP" 30x "FOR REFERENCE ONLY" 2404400-1 INSPECTIONLABEL-BK-222 222 2220 108x "INSPECTED OK" 50.8 x 19.1 2.0 x 0.75 60x "REJECTED" 50.8 x 12.7 2.0 x 0.5 54x "HOLD FOR 50.8 x 19.1 2.0 x 0.75 INSPECTION" 84x 50.8 x 15.9 2.0 x 0.625 “CALIBRATION” 2404500-1 CALIBATIONLABEL-BK-247 247 2470 108x “CAL.” Ø 15.9 Ø 0.625 55x “OUT OF CALLIB. DO NOT USE” Ø 12.7 Ø 0.5 PAGE 4 CLASS 1 DATA CLASSIFICATION - SEE POLICY TEC-02-04 INDUSTRIAL /// TTDS-249 – REMOVABLE Q-CEE’S LABELS TECHNICAL DATA SHEET Removable Q-Cee’s Labels-Type QC, PM, MAM & MQC Kit Label Details Label dimensions Packing Part No. Part Description No. of labels per Kit No. of labels per pack (10 Kits per bag) Label Image Label Quantity & description 150x "TESTED" 2388600-1 MAINTENANCELABEL-BK-282 282 2820 (w /h) mm in 50.8 x 12.7 2.0 x 0.5 72x "PREVENTATIVE 50.8 x 15.9 2.0 x 0.625 MAINTENANCE 30x "OUT OF SERVICE" 50.8 x 12.7 2.0 x 0.5 30x "DEFECTIVE DO 50.8 x 12.7 NOT USE" 2.0 x 0.5 www.te.com TE Connectivity, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2023 TE Connectivity Ltd. family of companies All Rights Reserved. CLASS 1 DATA CLASSIFICATION - SEE POLICY TEC-02-04 INDUSTRIAL /// TTDS-249 – REMOVABLE Q-CEE’S LABELS TECHNICAL DATA SHEET PAGE 5