27E125..

Signal Signal Relays Potter & Brumfield Sockets & Accessories, R10 Relays n Sockets for 2 - 6 pole relays or screw terminal sockets n Choice of grounding provision on sockets n Hold down springs n Plates and brackets permit various mounting options n Solder, PCB Ordering Code Approvals UL E59244, CSA LR15734 Technical data of approved types on request Technical Data Socket contact material Spring brass, tin plated Socket body material 2 and 4 pole models Polyester 6 and 8 pole models Phenolic Maximum current 10A Voltage drop 30mV max. at 10A Dielectric strength 1,000Vrms Insulation resistance 109 megΩ Solder and PC terminal sockets Rugged, molded socket body retains floating terminals of either solder or printed circuit pin configuration. PC terminal sockets are offered with pins in either 0.1” (2.54mm) grid or in-line arrangement. Grounding provisions Product Poles Code 27E125 27E126 27E127 27E162 27E163 27E164 27E128 27E129 27E130 27E212 27E213 27E271 27E193 27E194 27E636 27E637 2 4 6 2 4 6 2 4 6 2 4 6 2 4 2 4 27E342 27E629 27E630 2 4 6 Terminal type Grounding provision Part number solder terminals strip 1393143-8 1393143-9 1-1393143-0 1-1393143-6 1-1393143-7 1-1393143-8 1-1393143-1 1-1393143-2 1-1393143-3 2-1393143-4 2-1393143-5 3-1393143-1 2-1393143-1 2-1393143-2 5-1393143-0 5-1393143-1 none PCB terminals,.180” (4.57mm) long, staggered layout strip none terminal PCB terminals, 210” (5.33mm) long, staggered layout PCB terminals,.180” (4.57mm) long, in-line layout strip none 3-1393143-6 4-1393143-8 4-1393143-9 All accessories must be ordered separately. Pre-installed on sockets Not for use at 5A AC and above. Grounding Strip: Mounting stud of relay contacts grounding strip. Grounding strip is grounded with screw or rivet through round hole in socket. Grounding Terminal (PC sockets only): Mounting stud of relay contacts ground terminal through square hole in socket. Strip Caution: Printed circuit sockets are manufactured with “floating” (loose) terminals. This permits them to align with holes in the circuit board and with the relay terminals. During the mounting and soldering of the socket, vertical float should be eliminated and the terminals seated on the board. (This may be accomplished by inserting a dummy relay in the socket.) Failure to eliminate float may cause fracture of the solder joint or separation of the copper conductor from the printed circuit board when a relay is inserted in the socket after soldering. Terminal 10-2012, Rev. 1012 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. 161 Signal Signal Relays Potter & Brumfield Sockets & Accessories, R10 Relays (Continued) Dimensions PCB layout Solder and PC terminal sockets Sockets with staggered PC terminals 2 POLE .978 (24.84) 4 POLE 1.184 (30.07) 6 POLE 1.390 (35.31) .175 (4.45) .750 (19.05) .350 (8.89) .032 (.81) .330 (8.38) B .235 (5.97) CLEARANCE HOLE FOR RELAY MNTG. STUD & GROUND SPRING .312 (7.92) .519 4 POLE (13.18) .725 6 POLE (18.42) 2 POLE .120 DIA. HOLE .165 (3.05) (4.19) .100 (2.54) GRID .210 (5.33) A .065 (1.65) .090 (2.29) .625 (15.88) .500 (12.70) 6 4 POLE POLE .500 (12.70) .045 x .090 (1.14 x 2.28) PC Socket Dim. Term. Length A Dim. B .180 in .180 .115 (4.57) (2.92) .210 in .210 .156 (5.33) (3.96) ( HOLES + .004 DIA. .056 - .000 + .10 1.42 - .00 ) 2 POLE .100 .150 (2.54) (3.81) .450 HOLE FOR GROUND (11.43) TERMINAL (IF REQ’D.) ±.010 TOLERANCES ( ± .25 ) UNLESS OTHERWISE SH OW N Sockets with inline PC terminals .210 (5.33) .320 (8.13) PCB layout (top view) Sockets with solder terminals .110 (2.79) .530 .420 (13.46) (10.67) .400 .550 (10.16) (13.97) .450 (11.43) .281 (7.14) 2 POLE .343 (8.71) 4 POLE .562 (14.27) 6 POLE .781 (19.84) + .140 (3.56) .656 ± .015 (16.66 ± .38) 162 + .354 (8.99) 10-2012, Rev. 1012 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company. HOLES + .004 DIA. - .000 + .10 1.42 - .00 .056 ( ) 2 HOLES .109 DIA . (2.77) .281 ± .015 (7.14 ± .38) Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. Signal Signal Relays Potter & Brumfield Sockets & Accessories, R10 Relays (Continued) Ordering Code Product Poles Terminal Mount Grounding Code type type provision 27E317 27E152 27E446 27E447 27E448 27E460 27E461 27E462 2 4 2 4 6 2 4 6 solder bracket strip solder flange strip screw track/ chassis none Part number 3-1393143-4 1-1393143-5 4-1393143-1 4-1393143-2 4-1393143-3 1393837-1 4-1393143-4 4-1393143-5 All accessories must be ordered separately. Dimensions Track mount sockets 27E460, 27E461, 27E462 Bracket Mount socket 27E317 and 27E152 Provides front wiring, screw terminal connections for R10 family relays. No grounding provision. Allows solder terminal relay to mount flat on a chassis. 2 pole terminal wiring code X= 2 POLE .978 (24.84) 4 POLE 1.184 (30.07) .210 TYP. (5.33) .85 MAX. (21.6) (2) MTNG. HOLES .187 DIA. (4.75) 6 7 5 1 2 X .075 (1.91) .437 (11.10) .150 (3.81) .484 (12.29) + +++ +++ +++ +++ #6-32 SCREWS 10 8 9 4 3 A .156 (3.96) TAPPED #6-32 THREAD .058 (1.47) MATERIAL THICKNESS .437 (11.10) .062 ± .0 07 (1.57 ± .178) Solder terminal socket with tin-plated terminals and grounding strip pre-assembled on .065” (1.65mm) steel mounting plate. Requires only one chassis cutout. .175 REF. (4.45) SUGG CHASSIS CUTOUT .065 (1.65) .045 x .090 (1.14 x 2.28) SLOT IN TERMINAL S A B .187 ± .010 (4.75 ± .25) .320 REF. (8.13) Socket Poles Dim A Dim B Dim C 2 1.437 (36.50) 1.822 (46.27) .937 (23.80) 27E447 4 1.687 (42.85) 2.072 (52.63) 1.125 (28.58) 27E448 6 1.875 (47.63) 2.260 (57.40) 1.343 (34.11) 4 pole terminal wiring code 9 10 8 7 5 6 1 2 2 HOLES .147 DIA . (3.73) .687 (17.45) C .25 (6.35) + 6 pole terminal wiring code 9 12 + 13 21 11 22 10 + + + 20 + + 19 8 + ++ + ++ 7 + + + + 17 5 16 ++ + 6 14 18 15 1 + 4 2 3 15 16 14 13 + + + 11 12 4 + 3 ++ + ++ + ++ + ++ + Suggested track mounting .187 MIN . (4.75) Suggested chassis mounting 27EXXX PC BOARD 24A110 40G432 1.375 TRACK INSULATOR (34.93) 1.12L x .41W x .26H 24A071 (28.4 x 10.4 x 6.60) MOUNTING CLIP 10-2012, Rev. 1012 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. .530 MAX. (13.46) 27E446 .210 (5.33) 2 MTG. HOLES .147 DIA . (3.73) C 1.375 ± .010 (34.93 ± .254) 2.75 ± .015 (69.85 ± .381) Flange mount socket 27E446, 27E447, 27E448 .780 MAX. (19.81) B + + .045 x .090 TYP. (1.14 x 2.28) .100 (2.54) Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions 27EXXX PC BOARD .187 MIN . (4.75) CHASSIS SUGGESTED STANDOFF .375 (9.53) DIA. MIN; .625 (15.88) DIA. MAX. (CUSTOMER SUPPLIED) OR INSULATOR (40G432) Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. 163 Signal Signal Relays Potter & Brumfield Sockets & Accessories, R10 Relays (Continued) Ordering Code Product Code Description Part number 20C249 20C250 20C251 20C266 20C259 20C300 20C301 37D645 24A110 24A071 Hold down spring for 2 pole R10 relays Hold down spring for 4 pole R10 relays Hold down spring for 6 pole R10 relays Hold down spring for 8 pole R10 relays Hold down strap for R10 relays in PC sockets Hold down spring for 2 pole R10S relays Hold down spring for 4 pole R10S relays Mounting strip - accepts 10 relays or sockets Mounting track Steel mounting clip with #6-32 screw use with 27E46_ sockets on 24A110 track Plastic insulator - use with use with 27E46_ sockets on chassis or with 24A071 clip on 24A110 track 3-1393159-5 3-1393159-6 3-1393159-7 4-1393159-1 4-1393159-0 4-1393159-4 4-1393159-5 7-1393143-3 1419111-6 1419111-5 40G432 Hold down spring Hold down strap (PC sockets only) 9-1393159-5 All accessories must be ordered separately. Dimensions 24A110 – Mounting track 37D645 – Mounting Strip Strip of .060” (1.52mm) aluminum contains ten pre-punched, breakaway mounting plates. Each plate accomodates a 2, 4, 6 or 8 pole solder terminal R10 relay or socket to facilitate chassis- or rack mounting. 1.205 .535 (13.59) .25 (6.4) 2.50 (63.5) Mounting track is designed to accept snap-mount sockets, as well as other P&B screw terminal sockets. Track is made of lightweight, sturdy extruded aluminum and is shipped in three-foot (914cm) lengths with mounting holes on six-inch (152mm) centers. Track can be cut to shorter lengths or used end-to-end. .13 (3.3) 1.205 (30.61) (30.61) .090 R. (2.29) 3.00 (76.2) 6.00 (152.4) 36.00 ± .060 (914.4 ± 1.52) 1.375 ± .010 (34.93 ± .254) “A” = .109 DIA . (2.77) 2.000 (50.80) “A” + + “A” 1.135 (28.83) + + .32 (8.1) .090 (2.29) .750 (19.05) .187 (4.75) .405 ± .0 07 (10.29 ± .178) .180 (4.57) .16 (4.1) 24A110 40G432 24A071 164 10-2012, Rev. 1012 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change.