29-511-12

KISSLING SINGLE POLE POWER RELAYS Series 29 / 500A - from TE Connectivity (TE) The economical 29 series single coil relays with 500 amps (A) are developed using our competence and expertise gathered over decades of manufacturing to meet even the most demanding operating requirements. This single coil system relay features high shock and vibration resistance predominantly from its careful design and an optimized magnetic circuit. The sealing technology used in these relays meets both the IP67 and IP6K9K (Steam pressure cleaning) protection standard. This relay series is well suited for various applications in severe conditions. Other important advantages are low heat generation in the contact area based on low contact voltage drop, a compact design, low holding current, silver alloy contact material and the use of mechanical and high thermal stability insulating compounds. Both the terminals and the housing are protected against corrosion. Features • Sealed housing conforms to IP6K9K • Robust design • Minimized coil current • Variety of configuration options • 6G shock and 4G vibration resistant • Main contact current rated for continuous current and 100% duty cycle • Efficient coil and magnetic circuit design with switching properties and holding current requirements By equipping these relays with blow-out magnets, contact voltages are also achievable up to 250VDC. The use of blow-out magnets are also recommended for contact voltages over 40VDC and for inductive load applications to maintain long contact life at all voltages. Also available are various bracket styles to meet your installation conditions and suppression devices to eliminate electromagnetic interference at the coil and optional auxiliary contacts. Applications • Truck • Bus • Ground support vehicles • Construction and agricultural vehicles • Fork lift applications Circuits NO-Contact/Auxiliary-Contact NO-Contact 88 1 88a 2 86 A1 85 A2 Suppression diode 87y 87b 88y 88b 88 1 88a 2 86 A1 85 A2 Suppression diode Industrial & Commercial Transportation / Series 29 - 500A Page 1 SERIES 29 500A Specification Technical Data Temperature range -40°C to +85°C Protection IEC 60529 & DIN 40050-9 - IP67 (0,2bar, 1min) and IP6K9K Shock 6g / 11msec Vibration 4g / 50-2000Hz Thread sizes / Torque M4 = 2.0 - 2.2Nm | M12 = 18 - 22Nm Electrical Characteristics Min. Insulation resistance 100MΩ After live or environment 50MΩ Dielectric withstanding voltage 1050VAC / 1min at 50Hz Max. Contact drop, initial 150mV Contact drop after life test 175mV Continuous current 500A Overload 4000A - 1sec / 1800A - 20sec Rated contact load 12 / 24 / 28VDC 80VDC Resistive load 500A 300A Cycles 100.000 100.000 Mechanical life 2.000.000 cycles 2.000.000 cycles Coil Data 12VDC 24 / 28VDC 36VDC 48VDC 60VDC 80VDC Voltage range 9-16VDC 18-32VDC 27-48VDC 36-54VDC 45-68VDC 60-90VDC Nominal voltage 12VDC 28VDC 36VDC 48VDC 60VDC 80VDC Pick up voltage max. 9VDC 18VDC 27VDC 36VDC 45VDC 60VDC Drop out voltage min. ≤ 2VDC ≤ 4VDC ≤ 5 VDC ≤ 8VDC ≤ 10VDC ≤ 10VDC Coil resistance 9Ω ± 10% 36Ω ± 10% 97Ω ±10% 166Ω ± 10% 195Ω ± 10% 350Ω ± 10% Coil current approx. 1.33A 0.78A 0.40A 0.30A 0.30A 0.23A Coil power approx. 22W 22W 15W 16W 18W 19W Operating times NO-Contact relay Operate max. 60msec Bounce max. 5msec Release max. 30msec Wire Section min. 240mm2 / 0.372 sq.inch / MCM 500 Mounting position optional Industrial & Commercial Transportation / Series 29 - 500A Page 2 SERIES 29 500A Technical drawings Side mounting Bottom mounting 37 37 M12 25 25 M12 DIN439 B12 DIN137 8 34.5 38 52 8.5 130 122 6.5 M4 ISO1207 68 60 - 78 68 94 89 86 A1 88a 68 1 2 88a 1 85 A2 A1 88 2 A2 85 Options: Auxiliary contact 53 34.5 140.5 122 Options: Magnetic blowout 6.8 86 88 50 2.5 42.5 76 68 60 - 78 M4 ISO1207 68 86 A1 1 88a 88 2 1 85 A2 A1 88a 42.5 86 88 2.5 2.5 42.5 60 - 78 2 A2 85 88 Industrial & Commercial Transportation / Series 29 - 500A Page 3 SERIES 29 500A Ordering Information Part Number example: 29.511.02 29.5_ _._ _ _ Current 5 Options Current 500A Contacts 1 Make Contact NO Mounting 1 Standard side mounting 3 Bottom mounting A Auxiliary contacts* B Magnetic blowout (required over 40VDC) * Not possible for bottom mounting and NO/NC relay Coil voltage 1 12V 2 24 / 28V 3 36V 4 48V 6 60V 8 80V Suppression 0 Without suppression 1 With suppression te.com TE Connectivity, TE, TE connectivity (logo), KISSLING (logo) and KISSLING (word) are trademarks owned or licensed by the TE Connectivity family of companies. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2020 TE Connectivity | All Rights Reserved. K1166703 | Version 08/2020 Industrial & Commercial Transportation / Series 29 - 500A Page 4