3-1618394-1

KILOVAC High Voltage DC Contactors KILOVAC EV200P Series Latching Contactor With 1 Form X (SPST Latch) Contacts Rated 500+ Amps, 12-900 Vdc Product Facts Pick Up/Latch (Max) @ 25°C — 9 Vdc Hold (Min) — N/A Reset (Max)/Dropout (Min) — 9 Vdc Duty Cycle, Max 7 — 20% Coil Resistance @ 25°C — 2.5 Ω Operate Specs @ 25°C — Operate Time (Typ) — 15 ms Operate Bounce (Max) — 7 ms Release Time (Max) — 15 ms n Latching version of popular EV200 Series n Designed to be the smallest, lowest cost, lightest weight sealed contactor in the industry at its current rating n Optional auxiliary contacts for monitoring position of power contacts n Hermetically sealed — operates in explosive/ harsh environments with no oxidation or contamination of coil or contacts during long periods of non-operation n Not position sensitive, can be mounted in any orientation n RoHS versions available Physical Data Contact Arrangements — Main Contacts — SPST, Latching Auxiliary Contacts 1 — Up to 2 Form A Dimensions — See drawing Weight, Nominal — .95 lb. (.43 kg) Environmental Data Shock, 11ms 1/2 Sine (Operating) — 30 Gpeak Sine Vibration, 20 Gpeak — 55-2000 Hz Random Vibration, 14.06 Grms — 15 Hz (.002 G2/Hz), 100 Hz (.002 G2/Hz), 450 Hz (.12 G2/Hz), 900 Hz (.12 G2/Hz), 2000 Hz (.083 G2/Hz) Operating Temperature Range — -40°C to +85°C Electrical Data Coil Data 5 Nominal Coil Voltage 6 — 12 Vdc Ordering Information Typical Part Number EV200 P 4 A N A Series: EV200 = 500+ Amp, 12-900VDC Contactor 7 Contact Form: P = Latching F = Latching with 1 SPDT Aux. Coil Voltage: 4 = 12 Vdc 5 = 24 Vdc 6 = 48 Vdc KILOVAC High Voltage DC Contactors For factory-direct application assistance, dial 800-253-4560, ext. 2055, or 805-220-2055. Voltage Rating — Main Contacts (Max) — 750 Vdc Current Rating, Continuous — Main Contacts 2 — 500A Contact Resistance — Main Contacts 3 — 0.2 mΩ max above 300A 0.3 mΩ max between 50 and 300A Hot Switching Performance (Positive Polarity) 4 — 200A make/ break @ 270Vdc — 10,000 cycles 600A make/ break @ 360Vdc — 100 cycles 800A break only @ 360Vdc — 15 cycles 2000A break only @ 360Vdc — 1 cycle Mechanical Life (Min) — 75,000 cycles Dielectric Withstand Voltage — Terminal to Terminal/ Terminals to Coil — 1mA max @ 2,200 Vrms Insulation Resistance — Terminal to Terminal/ Terminals to Coil — 100MΩ min @ 500Vdc new 50MΩ min @ 500Vdc end of life Notes: 1 Product can be configured alternately with form B or C auxiliary switches if required. This changes the product part number, depending on specific auxiliary configuration. Consult TE for availability and part number 2 Ambient conditions and conductor design affect rating. Terminal temperature rise should be 75°C max above ambient. Keep relay terminals below 150°C max continuous, 175°C max for two hours, and 200°C for 1 minute. 3 Stabilized reading. Contact resistance may exceed spec in the first 10 minutes of current carry. 4 Units are polarity sensitive. Approximately 50% de-rating for reverse polarity switching. Consult factory for review of specific requirements. 5 Over temperature range unless noted. Suggested coil pulse = 50-100 ms. 6 24V and 48V coils available on request — consult factory. 7 Intermittent Duty Coil. Coil overheating can occur if duty cycle Coil Terminations: A = 15.3 in. (300 mm) Coil Termination Connector: N = None Mounting & Power Terminals: A = Bottom Mount & Male 10mm x M8 Threaded Terminals PAGE 39 KILOVAC High Voltage DC Contactors KILOVAC EV200P Series Latching Contactor (Continued) Outline Dimensions For factory-direct application assistance, dial 800-253-4560, ext. 2055, or 805-220-2055. AEROSPACE, DEFENSE & MARINE /// HIGH PERFORMANCE RELAYS