Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors
True Hot-Plug, Blind-Mating Mixed Signal and Power Connectors
Cable Mounted Products
Product Facts
■
Wide variety of contact sizes
and styles from 1 Amp
signals up to power contacts
rated at up to 200 Amps each
■
Sequenced contacts for
“mate-first-break-last”
operation
■
Floating panel-mount
connectors float up to
+/- 2 mm
■
High durability specific
products ranging from
100 to 1000 mate/un-mate
cycles
■
Customizable products
allow the freedom to add or
remove power or signal
contacts to meet specific
application requirement
■
Most products recognized
to US and Canadian
requirements under the
Component Recognition
program of Underwriters
Laboratories File No.
E28476
AND
®
R
C
US
Typical Applications
■
Low noise power supplies
■
Switch-mode power
supplies (SMPS)
■
Power factor-correcting
(PFC) power supplies
■
Systems requiring mounting
to backplane or chassis
■
Redundant (N + 1) power
systems
■
“Live” hot-plug power
supplies
■
All ELCON drawer
connectors in this section
are RoHS compliant
Tyco Electronics offers a
wide selection of blindmateable “drawer” connectors to suit modular
equipment designs. The
term “drawer connector”
was created to describe a
cabinet drawer where the
connector is installed at the
back of the drawer and is
mated by closing the
drawer. Since the “drawer”
is often times made with a
somewhat loose fit — to
enable easy opening and
closing, the drawer connector must provide sufficient
self-alignment and ideally a
floating connection to the
cabinet or drawer to keep
the connection from binding.
The power drawer connectors in this catalog are
divided into two separate
categories: high power
drawers and low power
drawers. Specifically, the
Technical Documents
Product Specification
108-2285
Application Specification
114-13206
product line names in these
two categories are:
High Power Drawer Connectors
■ ELCON Drawer Series
Connectors
Low Power Drawer Connectors
■ AMP Drawer Series
Connectors
■ Mini Power Drawer
■ Blind-mate Drawer
Connectors
■ Hybrid Mini Drawer
Connectors
Some of the benefits of the
power drawer connectors
from Tyco Electronics are
the robustness of the
housing designs and the
durability of the contacts.
High-end applications such
as networking switches and
servers want the lowest
possible voltage drop
across the connector.
For these applications the
high conductivity screwmachined contacts with
either gold or silver plating
offer the best performance.
The contacts are the core
of the ELCON drawer
series connectors. For cost
sensitive applications the
different hybrid drawer
connectors offer a wide
variety of shapes and sizes
aimed at keeping cost minimized and still providing a
reliable separable interface.
Regardless of the application, Tyco Electronics offers
a wide variety of power &
signal blind-mateable
drawer connectors.
Need more information?
Call Technical Support at
the numbers listed below.
Technical Support is staffed
with specialists well versed
in all Tyco Electronics
products. They can provide
you with:
■ Technical Support
■ Catalogs
■ Technical Documents
■ Product Samples
■ Tyco Electronics
Authorized Distributor
Locations
62
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors
True Hot-Plug, Blind-Mating Mixed Signal and Power Connectors (Continued)
Probe-proof Double
CROWN BAND Contacts
The size #0 contacts used
in the Top Drawer, Double
Drawer, DualPower and
QuadPower connectors
are also available in a
probe-proof double
CROWN BAND version.
These contacts are specially suited for operatorserviced power supplies
that require extra safety
protection.
ELCON drawer connectors
support various termination
styles, including crimp for
cable, solder tail and compliant press-fit for mounting
Wide Array of
Standard Contacts
All signal and some power
contacts are available in
various lengths to allow
multiple levels of sequencing, thus giving the engineer
further design flexibility.
Mating Polarization
To provide for positive
housing mating of
connectors, polarization
is provided in the form of
molded-in guide posts or
pre-installed guide pins.
Regulatory Agency
Certifications
Tyco Electronics ELCON
drawer series connectors
have been evaluated and
found to comply with the
UL1977 standard and the
CSA standard C22.2 No.
182.3-M1987.
Cable Mounted Products
3 mm Diameter Test Probe in
Accordance with IEC 435
Protective Cap (insulator)
Signal/Power Sequencing
Tyco Electronics can also
work with the customer to
obtain application-specific
regulatory certifications if
needed.
®
C
US
to PCB, and internal/
external threads for termination to lugs and/or busbars.
See table below for details.
Termination
Contact Size
#20
#16
#12
#8
#4
#0
PC Tail
Press-fit
Crimp
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Threaded
Internal
External
•
•
•
•
•
•
Application-Specific Designs
If none of our standard
drawer connectors
satisfies your requirements,
Tyco Electronics can
develop an ELCON connector design specific to
your application. We will
work closely with your engineers to fully understand
the design requirements
and develop an interconnect solution that meets
your stated needs. After the
concept and design stages,
Tyco Electronics produces
prototypes that perform
both electrically and
mechanically the same as
production parts. These
machined parts are used
for testing, regulatory
agency evaluations and
even as pre-production
components, allowing the
shortest lead time from
concept to manufacturing
in the industry.
Concept
Design
Prototypes
Production
Tyco Electronics engineers
work closely with the customer to fully understand
the design requirements.
A sketch drawing of the
design concept is created
for customer review, and the
design is finalized only when
it fully meets the requirements of the customer.
The design is frozen and
work on the mold tools starts.
Meanwhile, Tyco Electronics
builds prototypes that are
identical to the production
parts.
By the time the customer
is ready for production, all
requirements for release
to production, such as
qualification and regulatory
agency approval, have
been cleared.
63
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
How to Tailor Your ELCON Drawer Connector
this purpose. Complete a form for the pin and socket side
of your connector as indicated in the instructions and fax it
to your Tyco Electronics sales engineer. We will issue a
unique part number specific to your configuration, which
you can then use to place orders. Samples and customer
drawings are also available upon request.
If you selected a standard drawer connector for your application, before placing an order you need to specify your
application-specific requirements, such as housing type,
contact loading, and termination style. Layout forms for all
standard drawer connectors, such as the one shown below,
are available online at http://www.tycoelectronics.com or
can be obtained from Tyco Electronics customer service for
Pin Assembly
ENTER CUSTOMER INFORMATION
Cable Mounted Products
1. Choose one housing from the Pin Housing Selection Menu table. Place
an X in the appropriate guide pin circles, if guide pins are required.
2. Write the total quantity of each pin contact you require for each pin
assembly in the Qty column of the Pin Contact Selection Menu table.
3. Crimp contacts are shipped uninstalled. Threaded and PCB tail
contacts are installed by Tyco Electronics; enter the letter reference
of the desired contact in the appropriate contact positions on the
drawing: e.g., if you need a size #20 premate PCB tail standard contact to be installed in contact position #10, write “Q” in circle #10.
4. Sign, date and send the completed form to your local Tyco Electronics
Sales Engineer.
Pin Connector (Rear Face)
Pin Contact Insertion Side
Pin Connector Rear Face Cavity Identification
G1
Company
Location
Contact Name
Title
Telephone
Fax
Email Address
I am: ❏ End user
❏ Contract manufacturer (end user:
Signature
Annual Quantity Required
Submit to your local Tyco Electronics Sales Engineer.
Pin Housing Selection Menu
G2
Part Number
1648183-1
1
)
Today’s Date
Description
Housing without guides
Housing with guides (#6-32 thread)
Housing with guides (M3 x 0.5 thread)
Check
One
2
Size #0
Pin Contact Selection Menu
Size
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Size #20
Size #16
47
48
49
Size #12 or
#12HP
50
G3
51
52
G4
Ref. Part Number
Termination Style & Pin Length
Qty.
A = 1766811-1
Crimp
B = 1766819-1
Probe Proof, crimp
C = 1766230-1
1/4-20 Internal Thread
D = 1766274-1
M6 x 1 Internal Thread
E = 1766269-1
Probe Proof, 1/4-20 Internal Thread
#0
F = 1766275-1
Probe Proof, M6 x 1 Internal Thread
G = 1766268-1
1/4-20 External Thread
H = 1766231-1
M6 x 1 External Thread
J = 1766270-1
Probe Proof, 1/4-20 External Thread
K = 1766276-1
Probe Proof, M6 x 1 External Thread
L = 1650155-1
Crimp, standard
M = 1650161-1
Crimp, premate
N = 1650162-2
Crimp, postmate
#20
P = 1650283-1
PCB tail, standard
Q = 1650065-1
PCB tail, premate
R = 1650226-1
PCB tail, postmate
S = 1766196-1
Crimp, standard
T = 1766198-1
Crimp, premate
U = 1766199-2
Crimp, postmate
#16
V = 1766222-1
PCB tail, standard
W = 1766223-1
PCB tail, premate
X = 1766818-1
PCB tail, postmate
Y = 1766193-1
Crimp, standard
Z = 1766195-1
Crimp, premate
AA = 1766196-1
Crimp, postmate
#12
AB = 1766245-1
PCB tail, standard
AC = 1766250-1
PCB tail, premate
AD = 1766249-1
PCB tail, postmate
AE = 1650153-2
Crimp, standard, Hot-Plug
AF = 1650156-2
Crimp, premate, Hot-Plug
#12 HotPlug
AG = 1650060-2
PCB tail, standard, Hot-Plug
AH = 1650074-3
PCB tail, premate, Hot-Plug
Crimp and Threaded contacts are removable. PCB tail contacts are non-removable.
Float-Mount Shoulder Screw
Top Assembly Part Number
Assigned by Tyco Electronics
Part Number
1650399-1
1650401-1
Description
Screw, No 10-32 UNC 2A
Screw, M5 x 0.8
Qty.
64
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Connector Mounting
All ELCON drawer series connectors can be fix-mounted or float-mounted using the designated shoulder screws to allow
improved gatherability for blind-mating of the connector. Panel cut out dimensions are shown on the customer drawing
specific to your ELCON drawer connector.
Panel Float Mounting
When float-mounting to a panel or chassis, use the stainless steel shoulder screws specified in the layout sheet or
customer drawing specific to your ELCON drawer connector. Shown in the sketch below is an example of how the
Top Drawer connector is float-mounted to a panel.
Cable Mounted Products
Float-Mount of Top Drawer (Example)
Mounting
Flange
Panel (Ref)
Shoulder
Screw
Screw Description
#10-32 UNF 2A Thread
M5 x 0.8 Metric Thread
#8-32 UNF 2A Thread
#6-32 UNF 2A Thread
M4 x 0.7 Metric Thread
Part Number
1650399-1
1650401-1
1650402-1
1650106-1
1650589-1
Guide Pin
Used On
Top and Double Drawer, Dual and QuadPower,
In-Line QuadPower, W5 Drawer
All Other Drawers
Panel Fix Mounting
As a rule of thumb, ELCON drawer connectors can be fix-mounted to a panel, in two ways: (1) by attaching a screw
through the top and bottom mounting flange of the housing; or (2) by attaching a screw into a threaded guide pin (for
those connectors that have one). An example of each case is shown in the sketches below.
Screw Through Mounting Flange of Housing
Screw Into Thread of Guide Pin (When Applicable)
Fix to the panel by attaching a commercially available
screw and a washer through the top and bottom mounting
flange of the housing.
You can optionally fix-mount housings that have a guide
pin by attaching a commercially available screw and
washer into the thread on the back of the guide pin, as
shown in the figures below.
Internally threaded
(6-32) guide pin
Commercially
available screw
and washer
Commercially
available screw
and washer
Guide pin
#6-32 or
M3 x 0.5 screw
.25
[6.35]
Note: All part numbers are RoHS compliant.
65
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Connector Mounting (Continued)
Strain Relief and Wire Dress
Cable Mounted Products
If required, wires can be bundled together and supported
with cable ties. Wires must not be stretched or confined in
any way that would restrict the floating action of the connectors. Therefore, the wires must remain perpendicular to
the connector and avoid an excessively sharp bend
radius. The minimum recommended distance for the cable
tie, and the minimum bend radius of a wire bundle are
shown in the figure to the right.
PCB Fix Mounting
When mounting to a PC board, the connector standoffs must be seated on the board. Hold-downs are recommended to
provide stability during the soldering procedure. PCB-mount hole patterns are shown on the customer drawing specific
to your ELCON drawer connector.
Flush PCB-Mount Drawer Connectors
Drawer Connectors with Cabled AC IN
.020 [0.51]
PC Board (Ref)
Wire
Connector
Standoffs
.020 [0.51]
Connector Engagement
To provide for proper mating of the connector when the power supply unit is fully engaged into the system, the gap
between the pin and socket (shown as dimension “A” in the sketch below) must be within the limit specified in the
customer drawing for your ELCON drawer connector. Failure to meet this requirement may compromise contact wipe.
Refer to the customer drawing for details. ELCON drawer connectors are polarized and will only mate in the correct
orientation (see sketch below).
Rib in Guide
Post Cavity
Notch in
Guide Post
66
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Connector Tooling
Insertion/Removal (I/R) Tools: Industry standard plastic I/R tooling is compatible with
all crimp contacts for pin and socket removal. The following tools are available from
Tyco Electronics.
I/R Tools
Size
Size #20 I/R tool
Size #16 I/R tool
Size #12 I/R tool
Size #8 removal tool
Size #4 removal tool
Size #0 removal tool
Color Code
Red/White
Blue/White
Yellow/White
Red
Blue
Light Yellow
Cable Mounted Products
Part Numbers
1643917-1
1643916-1
1643915-1
1643914-1
1643922-1
1643921-1
Note: PCB tail contacts are non-removable.
Wire strip length: If inserting stranded wire into crimp style contacts, please use the table
below to determine the proper strip length of the wire.
Contact Size
“L” + .020 [0.51]
Wire Size AWG
inches
0.210
0.270
0.270
0.500
0.500
0.600
#20
#24 - #20
#16
#20 - #16
#12
#14 - #12
#8
#10* - #8
#4
#6* - #4
#0
#2* - #0
*Ref: MS3348 “Contact Bushing, Electric, Wire Barrel”
mm
5.33
6.86
6.86
12.70
12.70
15.24
Crimp Tools: The following table lists applicable MIL-STD crimp tools for contacts
Size
Type
Crimp Tool
Turret head/locator
Crimp Tool
Indenter head
Locator
Crimp Tool
Indenter head
Locator
Crimp Tool
Indenter head
Locator
12 - 24
8 - 10
4
0
MIL-STD
M22520/1-01
M22520/1-02
M22520/23-01
M22520/23-02
M22520/23-09
M22520/23-01
M22520/23-04
M22520/23-11
M22520/23-01
M22520/23-05
M22520/23-13
Part Number
601967-1
601967-2
—
—
—
—
—
—
—
—
—
Crimp Termination Wire Sizes: The following table shows crimp rear release contacts and
their respective wire sizes when crimped with applicable industry standard terminal tools.
Contact Size
#20
#16
#12
#8
#4
#0
Note:
(1)
Wire Range
AWG
20 - 24
16 - 18
12 - 14
10 - 8
4 (1)
1/0
mm2
0.241 - 0.616
0.963 - 1.23
1.94 - 2.98
4.74 - 8.61
21.60
53.00
Consult Tyco Electronics for smaller wire sizes in #4 contacts
Note: All part numbers are RoHS compliant.
67
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Cable Mounted Products
ELCON Drawer Product Specifications
Materials
Housing
Crimp Contacts
PCB Tails
Socket Contact Hoods (when applicable)
Size #12 hoods, Hot-Plug
Crown contacts
Polyester, 30% glass-filled, UL 94V-0 black
High conductivity copper alloy
Brass
305 corrosion resistant steel
Beryllium copper
Beryllium copper
Plating
Size #20 and #12HP
Sizes #0, #4, #8, #16 and non-HP #12
Hot-Plug hoods and pin contacts
Socket Contact Hoods (when applicable)
Gold plated over nickel
Silver plated over nickel
Gold plated over nickel
Passivated
Mechanical
Size #20
Size #16
Size #12
Size #12 Hot-Plug
Size #8
Size #4
Size #0
Size #0 w/double Crown
Size #20
Size #16
Size #12
Size #12 Hot-Plug
Size #8
Size #4
Size #0
Size #0 w/double Crown
Typical
Insertion Forces
of individual
contacts
Typical
Extraction Forces
of individual
contacts
0.2
2.3
2.9
2.9
4.4
3.8
4.7
4.8
0.1
0.7
1.9
1.9
2.4
3.0
3.0
3.5
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
lb.
0.09
1.04
1.32
1.32
2.00
1.72
2.13
2.18
0.05
0.32
0.86
0.86
1.07
1.36
1.36
1.59
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
Electrical
Size #20
Size #16
Size #12
Size #12 Hot-Plug
Size #8
Size #4
Size #0
Size #0 w/double Crown
Typical
Voltage drop
of individual
contacts
Insulator dielectric strength
1.7 mV at 5A
3 mV at 15A
4.2 mV at 35A
4.7 mV at 35A
6.5 mV at 75 A
8.4 mV at 125A
6.3 mV at 200A
5.6 mV at 200A
1,500 VDC for 1 minute, per MIL-STD 1344, Method 3001
Regulatory Agency Evaluations
Contacts
AWG
AWG
AWG
AWG
AWG
#20
#16
#12 Top Drawer
#12 Others
#12 with sockets
CSA-22.2 No. 0-M91 182.30
M1987 (CNR)
4A / 250V
10A / 250V
25A / 600V
25A / 250V
25A / 250V
Size #12 hot-plug
25A / 250V
Size
Size
Size
Size
55A / 250V
150A / 250V
—
100A / 250V
#8
#0 with single or double Crown
#0 using bus bar
#4
UL 498 and UL 1977 (USR)
5A / 250V
15A / 250V
35A / 600V
35A / 250V
35A / 250V
25A / 250VAC
35A / 120V
75A / 250V
200A / 250V
200A / 250V
125A / 250V
68
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors
Mini Drawer
Cable Mounted Products
Dimensions —
2.99" x 0.79" (75.9 x 20.1 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 12 / 16 x 6 contacts
Size 20 x 16 contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 12: Crimp and PCB tail
Size 16: Crimp and PCB tail
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
Size 12 + Size 20 + Size 12
Size 16 + Size 20 + Size 16
Size 12 + Size 20 + Size 16
1648110-1
1648111-1
1648112-1
1648115-1
1648116-1
1648117-1
Socket Housing
Size 12 + Size 20 + Size 12
Size 16 + Size 20 + Size 16
Size 12 + Size 20 + Size 16
1648206-1
1648207-1
1648208-1
Socket Housing
Size 12 + Size 20 + Size 12
Size 16 + Size 20 + Size 16
Size 12 + Size 20 + Size 16
Lower Drawer
Dimensions —
3.26" x 1.34" (82.8 x 34.0 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 12 / 16 x 8 contacts
Size 20 x 21 contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 12: Crimp and PCB tail
Size 16: Crimp and PCB tail
Size 20: Crimp and PCB tail
Base Housing Part Numbers
1648203-1
1648204-1
1648205-1
Pin Housing
Size 12 + Size 20 + Size 12
Size 16 + Size 20 + Size 16
Size 12 + Size 20 + Size 16
Note: All part numbers are RoHS compliant.
69
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
75A Middle Drawer
Cable Mounted Products
Dimensions —
3.31" x 1.31" (84.1 x 33.3 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 8 x 4 contacts
Size 12 x 9 contacts
Size 20 x 24 contacts
Current Rating — Up to 75 Amps
per size 8 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 8: Crimp, internal/external thread
and PCB tail
Size 12: Crimp and PCB tail
Size 20: Crimp and PCB tail
Float-Mount
Part Number 1648162-1
PCB-Mount
Part Number 1648163-1
Float-Mount
Part Number 6648167-1
PCB-Mount
Part Number 1648168-1
Base Housing Part Numbers
Pin Housing
1648162-1
Float-Mount
1648163-1
PCB-Mount
Socket Housing
Float-Mount w/
reinforced housing
1648168-1
PCB-Mount
6648167-1
Note: All part numbers are RoHS compliant.
70
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
125A Middle Drawer
Cable Mounted Products
Dimensions —
3.15" x 1.31" (80.0 x 33.3 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 4 x 2 contacts
Size 12 x 6 contacts
Size 20 x 32 contacts
Current Rating — Up to 125 Amps
per size 4 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 4: Crimp and internal/external
thread
Size 12: Crimp and PCB tail
Size 20: Crimp and PCB tail
Float-Mount
Part Number 1648151-1
PCB-Mount
Part Number 1648152-1
Float-Mount
Part Number 1648156-1
PCB-Mount
Part Number 1648157-1
Base Housing Part Numbers
Pin Housing
1648151-1
Float-Mount
1648152-1
PCB-Mount
Socket Housing
1648156-1
Float-Mount
1648157-1
PCB-Mount
Note: All part numbers are RoHS compliant.
71
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
200A Middle Drawer
Cable Mounted Products
Dimensions —
3.31" x 1.31" (84.1 x 33.3 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 4 x 2 contacts
Size 8 x 6 contacts
Size 12 x 3 contacts
Size 20 x 14 contacts
Current Rating — Up to 125 Amps
per size 4 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 4: Crimp and internal/external
thread
Size 8: Crimp, internal/external thread
and PCB tail
Size 12: Crimp and PCB tail
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
1648134-1
Socket Housing
1648135-1
Square Drawer
Dimensions —
2.76" x 1.24" (70.1 x 31.5 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 12 x 4 contacts
Size 20 x 36 contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 12: Crimp and PCB tail
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
1648132-1
Socket Housing
1648133-1
Note: All part numbers are RoHS compliant.
72
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
Top Drawer
Pin Side
Cable Mounted Products
Dimensions —
4.24" x 1.60" (107.8 x 40.7 mm)
Housing Variations — Various
guide pin configurations available.
Guides and Polarization —
Optional Steel Guide Pins with either
#6-32 or M3 internal thread
Available Contacts —
Size 0 x 2 contacts
Size 12 x 6 contacts
Size 16 x 12 contacts
Size 20 x 32 contacts
Current Rating — Up to 200 Amps
per size 0 contact
Contact Features — Hot-Plug size 12
contact option
Probe-proof size 0 contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 0: Crimp and internal/external
thread
Size 12: Crimp and PCB tail
Size 16: Crimp and PCB tail
Size 20: Crimp and PCB tail
Socket Side
Base Housing Part Numbers
Pin Housing
1648183-1
Socket Housing
1648186-1
Optional guide posts are available for improved alignment. Consult Customer
Service for details.
Double Drawer
Dimensions — 4.24" x 1.60" (107.8 x
40.7 mm)
Housing Variations — Various guide
pin configurations available.
Guides and Polarization — Optional
Steel Guide Pins with either #6-32 or
M3 internal thread
Available Contacts —
Size 0 x 4 contacts
Size 12 x 11 contacts
Size 20 x 24 contacts
Current Rating — Up to 200 Amps
per size 0 contact
Contact Features — Hot-Plug size 12
contact option
Probe-proof size 0 contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 0: Crimp and internal/external
thread
Size 12: Crimp and PCB tail
Size 20: Crimp and PCB tail
Pin Side
Socket Side
Base Housing Part Numbers
Pin Housing
1648552-1
Socket Housing
1648578-1
Optional guide posts are available for improved alignment. Consult Customer
Service for details.
Note: All part numbers are RoHS compliant.
73
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
DualPower Drawer
Cable Mounted Products
Dimensions —
1.80" x 1.60" (45.7 x 40.7 mm)
Housing Variations — Various
guide pin configurations available.
Guides and Polarization —
Optional Steel Guide Pins with either
#6-32 or M3 internal thread
Available Contacts — Size 0 x 2
contacts
Current Rating — Up to 200 Amps
per contact
Contact Features — Probe-proof
size 0 contact option
Contact Sequencing — Standard only
Contact Terminations —
Size 0: Crimp and internal/external
thread
Front Views
Side Views
Pin Side
Socket Side
Base Housing Part Numbers
Pin Housing
1648549-1
Socket Housing
1648575-1
Optional guide posts are available for improved alignment. Consult Customer
Service for details.
QuadPower Drawer
Dimensions —
2.50" x 1.60" (63.5 x 40.7 mm)
Housing Variations — Various
guide pin configurations available.
Guides and Polarization —
Optional Steel Guide Pins with either
#6-32 or M3 internal thread
Available Contacts — Size 0 x 4
contacts
Current Rating — Up to 200 Amps
per contact
Contact Features — Probe-proof
size 0 contact option
Contact Sequencing — Standard only
Contact Terminations —
Size 0: Crimp and internal/external
thread
Front
Views
Side Views
Pin Side
Socket Side
Base Housing Part Numbers
Pin Housing
1648548-1
Socket Housing
1648574-1
Optional guide posts are available for improved alignment. Consult Customer
Service for details.
Note: All part numbers are RoHS compliant.
74
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
In-Line QuadPower Drawer
Front View
Cable Mounted Products
Dimensions —
4.84" x 1.21" (122.8 x 30.7 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts — Size 0 x 4
contacts
Current Rating — Up to 200 Amps
per contact
Contact Features — Probe-proof
size 0 contact option
Contact Sequencing — Standard only
Contact Terminations —
Size 0: Crimp and internal/external
thread
Front View
Base Housing Part Numbers
Pin Housing
6651493-1
Socket Housing
6651494-1
W5 Power Drawer
Dimensions —
3.00" x 1.18" (76.2 x 30.0 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts — Size 4 x 5
contacts
Current Rating — Up to 100 Amps
per contact
Contact Features — Probe-proof
size 0 contact option
Contact Sequencing — Standard only
Contact Terminations —
Size 4: Crimp and internal/external
thread
Front View
Front View
Base Housing Part Numbers
Pin Housing
6651457-1
Socket Housing
6651458-1
Note: All part numbers are RoHS compliant.
75
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
P3S0 Drawer
Cable Mounted Products
Dimensions —
0.99" x 0.95" (25.0 x 24.0 mm)
Housing Variations — See Part
Numbers
Cable Socket to Panel-Mount Pin
Guides and Polarization —
Polarization only
Available Contacts — Size 12 x 3
contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power
Contact Terminations —
Size 12: Crimp only
Base Housing Part Numbers
Pin Housing
1766447-1
Socket Housing
1766448-1
P4S0 Drawer
Dimensions —
1.34" x .76" (34.0 x 19.4 mm)
Housing Variations — See Part
Numbers
Cable Pin to PCB-Mount Socket
Guides and Polarization —
Polarization only
Available Contacts — Size 12 x 4
contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Sequencing — Standard only
Contact Terminations —
Size 12: Crimp Pin and PCB tail Socket
Note: Supplied as kit, including
contacts
Base Housing Part Numbers
Pin Side Kit
6766014-1
Socket Side Kit
6766015-1
Note: All part numbers are RoHS compliant.
76
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
HV8P Drawer
Cable Mounted Products
Dimensions —
2.50" x 1.11" (63.5 x 28.2 mm)
Housing Variations — See Part
Numbers
600 V High Voltage Design
Guides and Polarization — Built in
Available Contacts — Size 12 x 8
contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power
Contact Terminations —
Size 12: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
1648127-1
Socket Housing
1648128-1
P10S0 Drawer
Dimensions —
2.96" x 1.00" (75.0 x 25.4 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts — Size 12 x 10
contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power
Contact Terminations —
Size 12: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
1648568-1
Socket Housing
1648596-1
Note: All part numbers are RoHS compliant.
77
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
P6S18 Drawer
Cable Mounted Products
Dimensions —
5.45" x 1.35" (138.4 x 34.3 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 4 x 6 contacts
Size 20 x 18 contacts
Current Rating — Up to 100 Amps
per size 4 contact
Contact Features — Standard
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 4: Crimp and internal/external
thread
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
6766615-1
Socket Housing
6651810-1
P10S22 Drawer
Dimensions —
4.12" x 0.79" (104.5 x 20.1 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 12 x 10 contacts
Size 20 x 22 contacts
Current Rating — Up to 35 Amps
per size 12 contact
Contact Features — Hot-Plug size 12
contact option
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 12: Crimp and PCB tail
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
1648211-1
Socket Housing
1648212-1
Note: All part numbers are RoHS compliant.
78
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Series Connectors (Continued)
P12S12 Drawer
Cable Mounted Products
Dimensions —
4.31" x 0.70" (109.5 x 17.8 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts —
Size 16 x 12 contacts
Size 20 x 12 contacts
Current Rating — Up to 15 Amps
per size 16 contact
Contact Features — Standard only
Contact Sequencing — Multi-level
for power and signal
Contact Terminations —
Size 16: Crimp and PCB tail
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
1651202-1
Socket Housing
1651203-1
P0S30 Drawer
Dimensions —
3.22" x 0.70" (81.8 x 17.8 mm)
Housing Variations — See Part
Numbers
Guides and Polarization — Built in
Available Contacts — Size 20 x 30
contacts
Current Rating — Up to 5 Amps per
size 20 contact
Contact Features — Standard only
Contact Sequencing — Multi-level
for signal
Contact Terminations —
Size 20: Crimp and PCB tail
Base Housing Part Numbers
Pin Housing
6651204-1
Socket Housing
6651205-1
Note: All part numbers are RoHS compliant.
79
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Standard Contacts
The ELCON drawer series connectors use standard
contacts across the product line. This section shows the
standard contacts available in different sizes and various
lengths and termination styles, with their respective
part numbers.
Cable Mounted Products
Pin Side Contacts
Contact Size #20 — For use in most drawer connectors
Contact Size #20
Termination
Type
Contact
Part Number
Crimp, standard
Crimp, premate
Crimp, postmate
PCB tail, standard
PCB tail, premate
PCB tail, postmate
1650155-1
1650161-1
1650162-2
1650283-1
1650065-1
1650226-1
A
Dimensions
in
0.32
0.47
0.27
0.32
0.47
0.27
mm
[8.12]
[11.93]
[6.85]
[8.12]
[11.93]
[6.85]
Contact Size #16 — For use in Mini Drawer, Lower Drawer, Top Drawer, and P12S12
Contact Size #16
Termination
Type
Contact
Part Number
Crimp, standard
Crimp, premate
Crimp, postmate
PCB tail, standard
PCB tail, premate
PCB tail, postmate
1766194-1
1766198-1
1766199-1
1766222-1
1766223-1
1766818-1
A
Dimensions
in
0.33
0.48
0.29
0.33
0.48
0.29
mm
[8.38]
[12.19]
[7.36]
[8.38]
[12.19]
[7.36]
Contact Size #12 — For use in Mini Drawer, Lower Drawer, 75A, 125A and 200A Middle Drawer;
Square Drawer, TOP Drawer & Double Drawer; P3S0 and P4S0, HV8P, P10SO, P10S22
Contact Part Number
Gold Plated
Silver Plated
1650153-2
1766193-1
1650156-2
1766195-1
1650158-2
1766196-1
1650060-2
1766245-1
1650074-3
1766250-1
1650073-3
1766249-1
Termination
Type
Crimp, standard
Crimp, premate
Crimp, postmate
PCB tail, standard
PCB tail, premate
PCB tail, postmate
Contact Size #12
A
Dimensions
in
0.43
0.46
0.39
0.43
0.46
0.39
mm
[10.92]
[11.68]
[9.90]
[10.92]
[11.68]
[9.90]
Note: For applications using the #12 hot-plug socket use of gold plated pins are recommended.
Contact Size #8 - For use in 75A and 200 A Middle Drawer
Contact Size #8
Termination
Type
Contact
Part Number
Crimp, standard
Crimp, premate
Crimp, postmate
A
Dimensions
1766192-1
1766197-1
1766821-1
in
0.43
0.48
0.33
mm
[10.92]
[12.19]
[8.38]
PCB tail, standard
1766262-1
0.43
[10.92]
PCB tail, premate
1766263-1
0.48
[12.19]
Contact Size #4 - For use in 125A and 200A Middle Drawer. P6S18 Drawer, W5 Power Drawer
Termination
Type
Contact
Part Number
Crimp, Standard
Dimensions
A
in
mm
1766232-1
0.51
[12.95]
1/4 - 20 x .050 DP
External Thread
1766812-1
0.51
[12.95]
M5 x 0.8 x 9.6 mm DP
M5 Internal Thread
1766283-1
0.51
[12.95]
Contact Size #4
Note: All part numbers are RoHS
compliant.
80
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Standard Contacts (Continued)
Pin Side Contacts (Continued)
Contact Size #0
Probe-proof
Termination
Type
Contact
Part Number
Crimp
Dimensions
A
in
mm
1766811-1
0.495
[12.57]
Probe-proof crimp2
1766819-1
0.430
[10.92]
1/4 - 20 x .050 DP
Internal thread
1766230-1
0.495
[12.57]
M6 x 1 x 12.7 mm DP
Internal thread
1766274-1
0.495
[12.57]
1/4 - 20 x .050 DP
Probe-proof/internal thread2
1766269-1
0.430
[10.92]
M6 x 1 x 12.7 mm DP
Probe-proof/Internal thread2
1766275-1
0.430
[10.92]
1/4 - 20 x .050 DP
External thread
1766268-1
0.495
[12.57]
M6 x 1 x 12.7 mm DP
External thread
1766231-1
0.495
[12.57]
1/4 - 20 x .050 DP
Probe-proof/external thread 2
1766270-1
0.430
[10.92]
M6 x 1 x 12.7 mm DP
Probe-proof/external thread2
1766276-1
0.430
[10.92]
Notes:
Cable Mounted Products
Contact Size #0
Contact Size #01 - For use in Top Drawer, Double Drawer, DualPower & QuadPower, In-Line QuadPower
1Contact
2Use
Tyco Electronics for alternate contact terminations.
only with probe-proof socket contacts.
and threaded contact are insertable/removable.
3Crimp
Socket Side Contacts
Contact Size #20
Contact Size #20
Termination
Type
Contact
Part Number
Crimp
1648325-1
PCB Tail
1648382-1
Contact Size #16
Termination
Type
Contact
Part Number
Crimp
6648319-1
PCB Tail
6648383-1
Contact Size #16
Contact Size #12
Contact Size #12
Termination
Type
Contact
Part Number
Crimp
Hot-Plug Crimp
PCB Tail
Hot-Plug PCB Tail
6648318-1
1648384-1
6648374-1
1648387-1
Note: For applications using the #12 hot-plug socket, the use of gold plated
pins are recommended (see page 80).
Note: All part numbers are RoHS compliant.
81
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ELCON Drawer Standard Contacts (Continued)
Socket Side Contacts
Cable Mounted Products
Contact Size #8
Termination
Type
Contact
Part Number
Crimp
6648317-1
PCB Tail
6648400-1
Contact Size #8
Contact Size #4
Contact Size #4
Termination
Type
Contact
Part Number
Crimp, Standard
6648434-1
1/4 - 20 x .050 DP
External Thread
6648435-1
M5 x 0.8 x 9.6 mm DP
M5 Internal Thread
6648335-1
Contact Size #01
Termination
Type
Contact
Part Number
Crimp
6648405-1
Probe-proof crimp2
6648418-1
1/4 - 20 x .050 DP
Internal thread
M6 x 1 x 12.7 mm DP
Internal thread
1/4 - 20 x .050 DP
Probe-proof/internal thread2
M6 x 1 x 12.7 mm DP
Probe-proof/Internal thread2
1/4 - 20 x .050 DP
External thread
M6 x 1 x 12.7 mm DP
External thread
1/4 - 20 x .050 DP
Probe-proof/external thread2
M6 x 1 x 12.7 mm DP
Probe-proof/external thread2
Contact Size #0
Contact Size #0
Probe-proof
6648416-1
6648428-1
6648419-1
6648429-1
6648417-1
6648430-1
6648420-1
6648431-1
Notes: 1Contact Tyco Electronics for alternate contact terminations.
2Use only with probe-proof Pin contacts.
3Crimp and threaded contact are insertable/removable.
Non-Standard Contacts
Contacts with pin lengths
and terminations other than
standard are available.
Consult customer service
if your design requires
contacts different from the
ones shown in this catalog.
Note: All part numbers are RoHS compliant.
82
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP Miniature Power Drawer (MPD) Connectors
Product Facts
High mating cycle life
Low Mating and Un-mating
force (< 0.2lbs per contact)
■ Single-piece molded
housing
■ Molded-in guide pins
provide generous
blind-mateability
■ Sizes: 3 – 10 positions
■ Compact size is ideal for
distributed DC power
applications
■ Two Levels of contact
sequencing
■ One contact for either solder
or press-fit termination
■ Hardware — Less or
traditional shoulder bolt
mounting
■ Minimum of 3 mm contact
wipe on shortest power
contact
■ All MPD connectors in this
section are RoHS compliant
■
■
Up to 16 Amps per contact
250 mating cycle durability
+/- 1.25 mm radial mis-alignment
capability. (Total float is 2.5 mm!)
1.6 mm sequencing distance — ideal
for modular sheet metal construction
applications
Minimum of 3 mm contact wipe on
shortest power contact
Maximum continuous operating
temperature — 105°C
UL 94 V-0 High-temperature thermoplastic housings
Cable Mounted Products
Specifications
The miniature power drawer
connector combines a high
density power interface in
a blind-mateable wire-toboard connector. The MPD
contact interface has been
previously qualified to
requirements similar to
BellCore GR-1217 in boardto-board applications. Now
available in a crimp-to-wire
version, the contacts are
rated for up to 15 Amps on
14 AWG wire. In addition,
the MPD contacts are
designed to meet UL 1977
hot-plug requirements for
up to 7.8 Amps at 48VDC.
The connection consists of
a vertical pcb mountable
receptacle and a panelmounted floating plug. The
vertical receptacle pcb tails
are designed for use in
either through hole solder
or press-fit applications.
The float-mount plug is easily installed from the inside
of the chassis without any
additional hardware, lending
itself to easy assembly of
pre-made cable assemblies.
Additionally, the staggered
wire exit pattern permits
the maximum number of
contact interfaces in the
least amount of connector
volume.
The compact design is
ideal for bringing power
to small rack-mounted
devices such as 1U
computer servers and
telecommunications
switches. The 3 mm centerline satisfies UL 1977 safety
requirements for 48 VDC
distributed power applications. For higher voltage
applications such as AC
input, the contacts can be
selectively loaded to handle
up to 300 V AC or DC.
Technical Documents
Product Specification
108-1998
Application Specification
114-13067
83
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP Miniature Power Drawer (MPD) Connectors (Continued)
Crimp Contacts
Insulation Barrel
Current Ratings
Plug Contact
Standard Power — 10 Amps
High Power — 16 Amps
Material and Finish
Cable Mounted Products
Standard Power:
Crimp Blade Contacts — Brass
Receptacle Contacts —
Phos. Bronze.
Finish — 0.38µm Gold over 1.27µm
Nickel
High Power:
Blades — High Conductivity Cu Alloy
Receptacle — High Conductivity Cu
Alloy
Finish — 1.27µm Gold over 1.27µm
Nickel
Contact Mating Length (Min.) —
Type A — 4.6 mm
Type B — 3.0 mm
Hot-Pluggability (With High
Current Contacts only) —
250 Cycles — 7.8 Amps @ 48VDC
Note: All contacts are Sn plated in the
crimp barrel or Sn in pcb interface
Plugs and Receptacles
Wire Barrel
PRO-CRIMPER Hand Tool
Part Number 91363-1
Locking Lance
Crimp Blade Contacts
Wire
Size
16-20
AWG
Type
Cycles
Standard
Power
100
High
Power
250
Mating
Length
A
B
A
B
Part Number
Strip Form
1489128-8
1489128-7
1-1489128-0
1489128-9
Applicator
Hand Tool
1385248-3
91363-1
Heavy Duty Miniature (HDM) Applicator for AMP-O-LECTRIC Model G Machine - #1385248-3.
PRO-CRIMPER Hand Tool #354940-1, Die set # 91363-2
Back of Plug
Assembly
Terminated
Plug Contacts
Plug
Housing
Materials
PC Board
Receptacle
Assembly
UL 94V-0 Thermoplastic
105°C Max. Operating temperature
Locking Lance
Note: Vertical PCB Mt. Receptacles
supplied with press-fit ACTION PIN
contacts.
Polarization
Feature
Number of
Positions
3
4
5
6
7
8
9
10
Part Number
Panel-Mount Plug
PCB-Mount Receptacles
Snap-In
Shoulder Bolt
Standard Power
High Current
1489127-1
—
1489715-1
1-1489715-1
1489127-2
1489701-1
1489715-2
1-1489715-2
1489127-3
—
1489715-3
1-1489715-3
1489127-4
—
1489715-4
1-1489715-4
1489127-5
—
1489715-5
1-1489715-5
1489127-6
—
1489715-6
1-1489715-6
1489127-7
—
1489715-7
1-1489715-7
1489127-8
—
1489715-8
1-1489715-8
Note: All part numbers are RoHS compliant.
84
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Blind-Mate Drawer Connectors
Product Facts
High current circuits and
signal circuits can be mixed
in the same connector
■
High current circuits use
MIC connector contacts
located at four corners of
the housing
■
Signal circuits use Standard
Drawer Connector contacts
■
24 positions
■
Hermaphroditic housing
can be mated with top and
bottom turned while
maintaining polarity
Cable Mounted Products
■
Hybrid Drawer Connectors
offer high current and
signal circuits mixed in the
same connector system.
hermaphroditic crimp snapin contacts that are used
in the Standard Drawer
Connector.
High current circuits use
MIC connector contacts
which are located at the
four corners of the housing.
The hermaphroditic housings are available in a popular 24-position size. These
housings can be mated
with top and bottom turned
while maintaining polarity.
Signal circuits use the same
Performance Specifications
Voltage Rating — 250 VAC
Current Rating (Max.) —
Signal Circuit (Drawer);
4 Amps — 24 AWG [0.2 mm2] Wire
5 Amps — 22 AWG [0.3-0.4 mm2] Wire
7 Amps — 20 AWG [0.5-0.6 mm2] Wire
Power Circuit (MIC);
10 Amps
Low Level Resistance —
Signal Circuit (Drawer);
10 milliohms max. (Initial)
20 milliohms max. (Final)
Power Circuit (MIC);
3 milliohms (Initial)
6 milliohms (Final)
Dielectric Withstanding Voltage —
5000 milliohms (Initial)
2000 milliohms (Final)
Operating Temperature —
–20°C to +120°C
85
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Blind-Mate Drawer Connectors (Continued)
Housings
(Hermaphroditic),
24 Positions
Signal Circuits
Power Circuits
(4 corners)
Housing — Glass-filled polybutylene
terephthalate (PBT), blue
Bushing — Brass, zinc-plated
B13
Material
A2
A1
A11
B14
.441
[11.22]
B23
2.756
[70.00]
1.181
[30.00]
.197 Pitch
[5.00]
1.771
[45.00]
A13
A14
B1
.440
[11.80]
2.394
[60.80]
A23
B2
Performance Specifications —
page 85
MIC Contacts — page 87
Crimp Snap-In Contacts — page 87
B11
Note: Reverse figures show circuit numbers.
Technical Documents
A1
(Example =
Product Specification
108-5371
The hole used for No. 1 circuit is
B13
Cable Mounted Products
Related Product Data
used for No. 13 on the reverse side.)
0.24
[6.10] 0.70
[17.9]
1.15
[29.1]
Panel Mounting Position
(Front Mounting)
Housing
Part Numbers
Floating of Bushing
Up- and downward = 0.05 [.002]
Circumferential = 0.14 [.006]
Up- and downward = 0.30 [.012]
Circumferential = 0.80 [.031]
5176916-1
5176916-2
Upward and downward = Axial clearance
Circumferential = Floating
Recommended Panel Cutout
2.835
[72.00]
2.394
[60.80]
2.157
[54.80]
.481
[12.22]
.130 Dia.
[3.300]
.378
[9.60]
1.953
[49.60]
1.260
[32.00]
.480
[12.18]
.197*
[5.00]
.197*
[5.00]
.098
R*
[2.50]
R1
All Corners
*Dimensions applicable for rear mounting.
Note: All part numbers are RoHS compliant.
86
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Blind-Mate Drawer Connectors (Continued)
MIC Contacts
(Used for Power Circuits)
Material and Finish
.827
[21.00]
Phosphor bronze, plated .000030
[0.00076] gold in contact area, remainder of contact gold flash, with entire
contact underplated nickel
Performance Specifications—
page 85
Housings—page 86
Technical Documents
Wire Size Range
AWG
mm2
Insulation
Diameter
20-14
.087-.134
2.20-3.40
0.5-2.0
Part Numbers
Receptacle Contact
Hand
Tool
Strip Form
Loose Piece
755338-1*
170286-4
170289-3
755339-1
Cable Mounted Products
Related Product Data
Applicator
567151-X**
*Part Number 755338-1 is used on wire for automotive application; Part Number 755339-1 is used on other types of
wire.
**Call Tyco Electronics for applicators.
Extraction Tool Part Number 723735-1
Instruction Sheets
408-089J, 408-369J, 408-370J
.126
[3.20]
Crimp Snap-In Contacts
(Hermaphroditic, Used for
Signal Circuits)
.791
[20.10]
Material and Finish
Phosphor bronze, plated gold in contact
area (for length of .236 [6.0] from tip),
with entire contact underplated nickel
Related Product Data
Performance Specifications—
page 85
Housings—page 86
Technical Documents
Instruction Sheets
408-097J, 408-151J
.146
[3.700]
Wire Size Range
AWG
mm2
Insulation
Diameter
24-20
0.2-0.6
20-16
0.5-1.4
.060-.077
1.50-1.95
.071-.130
1.80-3.30
Part Numbers
Applicator for
AMP-O-LECTRIC
Machine*
Contact
Strip Form
Loose Piece
Hand
Tool
170311-1
170313-1
567324-2
91591-1
170484-1
170485-1
567241-2
91590-1
*Applicators are for Model “K” machines. Consult Tyco Electronics for applicators for other bench machines and
lead-making machines.
Notes: For applicable wire, use wire specified in UL 1015 or 1007.
Extraction Tool Part Number 723986-1
Tab Contacts
Material and Finish
.118
[3.00]
Brass, plated .000030 [0.00076] gold in
contact area, with entire contact underplated nickel
.984
[25.00]
Related Product Data
Performance Specifications—
page 85
Housings—page 86
Wire Size Range
AWG
mm2
Insulation
Diameter
20-14
.087-.134
2.20-3.40
Technical Documents
Instruction Sheets
408-144J, 408-369J, 408-370J
0.5-2.0
Part Numbers
Tab Contact
Strip Form
Loose Piece
170221-4
170222-3
Hand
Tool
755338-1*
755339-1
*Part Number 755338-1 is used on wire for automotive application; Part Number 755339-1 is used on other types of
wire.
Extraction Tool Part Number 724763-1
Note: All part numbers are RoHS compliant.
87
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Special Blind-Mate Drawer Connectors (uses AMP-LEAF Contacts)
Cable Mounted Products
Product Facts
■
Blind-mate connectors
accept AMP-LEAF crimp
snap-in and solder dip
contacts
■
Contacts are phosphor
bronze, gold-over-nickel
plated
■
6 and 10 positions
■
Housings made of polybutylene terephthalate (PBT)
Special blind-mate drawer
connectors are available
in 6- and 10-position
configurations and provide
wire-to-board and wire-towire connection capabilities.
These connectors offer
the integrity of AMP-LEAF
contacts with maximum
travel wiping action.
Housings feature molded-in
guide pins and diagonally
aligned sockets for correct
polarization and to facilitate
blind-mating. The PC
header guide pins extend
through the PC board to
secure the header to the
board prior to soldering.
6-Position Socket Housing
(Accepts AMP-LEAF
Crimp Snap-In Contacts)
6-Position PC Board Header Housing
(Fully loaded with AMP-LEAF
Solder Dip Contacts)
Performance Specifications
Current Rating —
4 Amps (max.) — 26-22 AWG
[0.12-0.4 mm2] wire
10-Position Header Housing
(Accepts AMP-LEAF
Crimp Snap-In and
Solder Dip Contacts)
10-Position Socket Housing
(Accepts AMP-LEAF
Crimp Snap-In Contacts)
Voltage Rating — 50 VDC
Temperature Rating —
–10°C to +80°C
Mounting Screw
(2 Required per Socket
Housing)
2.17
[5.50]
.102
[2.60]
.220
[5.60]
Part Number 343404-1
.354
[9.00]
Material and Finish
Steel, plated bright zinc chromate
M 3 x 0.5
Thread
.197
[5.00]
Note: All part numbers are RoHS compliant.
88
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Special Blind-Mate Drawer Connectors (Continued)
Socket Housing,
6 Positions
.354
[9.00]
Part Number 343886-1
.177
[4.50]
1.009
[25.62]
.670
[17.00]
Accepts the following AMP-LEAF
Crimp Snap-In Contacts:
Part Number 583990-3 (loose piece)
Part Number 583204-2 (strip form)
.630
[16.00]
Cable Mounted Products
Contacts must be ordered
separately.
.187
[4.75]
Recommended Panel Cutout
.413
[10.50]
Material
Glass-filled polybutylene terephthalate
(PBT), black
1.441
[36.60]
.965
[24.50]
.187
[4.75]
.693
[17.60]
.728
[18.50]
.594
[15.10]
.354
[9.00]
.496
[12.60]
1.009
[25.62]
PC Board Header Housing,
6 Positions with Board
Retention
.482
[12.25]
.632
[16.06]
.322
[8.44]
.052 Dia.
[1.32]
.300
[7.62]
.450
[11.43]
Part Number 343887-1
.160
[4.06]
Accepts AMP-LEAF Crimp Snap-In
Contact Part Number 343371-1
and Solder Dip Contact
Part Number 583294-2
Contacts must be ordered
separately; refer to contact
specification pages for details.
.965
[24.50]
.157 Dia.
[4.00]
Recommended PC Board Layout
.150
[3.80]
.343
[8.70]
.965
[24.50]
.850
[21.60]
Material
Glass-filled polybutylene terephthalate
(PBT), black
.450
[11.43]
.150
[3.80]
Position No. 1
.039
[1.00]
.965
[24.50]
.559
[14.20]
.701
[17.80]
.150
[3.80]
Note: All part numbers are RoHS compliant.
89
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Special Blind-Mate Drawer Connectors (Continued)
Socket Housing,
10 Positions
.156
[3.96]
.929
[23.60]
.413
[10.50]
.130 Dia.
[3.30]
Part Number 343348-1
R3
Accepts the following AMP-LEAF
Crimp Snap-In Contacts:
Cable Mounted Products
1.240
[31.50]
.354
.807 [9.00]
[20.50]
Part Number 343371-1 (strip form)
Part Number 583204-2 (strip form)
Contacts must be ordered
separately.
R5
1.299
[33.00]
Recommended Panel Cutout
.748
[19.00]
Material
Glass-filled polybutylene terephthalate
(PBT), black
1.240
[31.50]
.874
[22.20]
.217
[5.50]
.413
.591
[15.00] [10.50]
.315
[8.00]
.850
[21.60]
.313
[7.95]
.205
[5.20]
.728
[18.50]
.374
[9.50]
.276
[7.00]
.772
[19.60]
1.299
[33.00]
1.732
[44.00]
R4
.354
[9.00]
.787
[20.00]
Header Housing,
10 Positions
.187
[4.75]
.965
[24.50]
.412
[10.47]
Part Number 343347-1
.433
[11.00]
Accepts AMP-LEAF Crimp Snap-In
Contact Part Number 343371-1
and Solder Dip Contact
Part Number 583294-2
.272
[6.92]
.290
[7.37]
Contacts must be ordered
separately: refer to contact
specification pages for details.
Material
Glass-filled polybutylene terephthalate
(PBT), black
.619
[15.71]
.419
[10.63]
.126
[3.20]
Recommended Panel Cutout
1.240
[31.50]
1.008
[25.60]
.590
[15.00]
.211
[5.35]
.720
[18.30]
.160
[4.00]
.850
[21.60]
.984
.413
[10.50] [25.00]
1.181
[30.00]
.126 x .433
[3.20 x 11.00]
1.535
[39.00]
.709
[18.00]
.118
[3.00]
.354
[9.00]
Note: All part numbers are RoHS compliant.
90
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Special Blind-Mate Drawer Connectors (Continued)
Crimp, Snap-In Contacts
Material and Finish
Wire Barrel Crimp
Insulation Support
Cable Mounted Products
Phosphor bronze, plated as follows:
Plating A — .000100-.000200
[0.00254-0.00508] tin (lubricant must
be used)
Plating B — .000030 [0.00076] min.
gold in mating area, gold flash on
remainder of contact, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating C — .000015 [0.00038] min.
gold in mating area, gold flash on
remainder of contact, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating D — .000030 [0.00076] min.
gold over .000050 [0.00127] min. nickel
in mating area, remainder of contact
gold flash over .000015 [0.00038] min.
nickel
Plating E — .000030 [0.00076] min.
gold in mating area, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating F — .000015 [0.00038] min.
gold in mating area, with entire contact
underplated .000050 [0.00127] min.
nickel
Terminal Stop
Locking Lance
Part Numbers
Wire
Range
AWG/mm2
Insulation Range
Single
Double
Wire
Wire
26-22
0.12-0.4
.050-.064
1.27-1.63
—
22-18
0.3-0.9
.055-.080
1.40-2.03
.120
3.05
Max.
16
1.25-1.40
.108
2.74
Max.
.080-.160
2.03-4.06
Contact
Loose
Strip
Piece
Form
583990-3
583204-2
—
343371-1
—
583361-2
583989-3
583361-3
583989-4
583361-4
—
583555-4
—
583555-6
583991-3
60151-6
Applicator for
Contact AMP-O-LECTRIC
Finish
Machine*
B
D
A
B
C
E
F
B
Hand
Tool
466366-2
90028-3
466367-2
90017-3 (1 #22-20)
90028-3 (2 #22)
90101-3 (1 #20)
466368-2
90031-8 (2 #18)
90101-3 (2 #20)
90101-3 (1 #16)
*Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench
machines and lead-making machines.
Notes: 1. Shorting contacts are available, consult Tyco Electronics.
Notes: 2. Contacts and housings to accommodate .093 [2.36] thick PC boards can be made available, consult
Tyco Electronics.
Hand Crimping Tool
Contact Extraction Tool
Technical Documents
Product Specifications
108-9013, 108-9043
Application Specification
114-9003
Instruction Sheets
408-6591, 408-7045, 408-7622,
408-7623, 408-7624, 408-7625,
408-7626
Crimp Inspection Sheet
CI 8050-33
Dummy Contact
Plain Finish—
Part Number 66084-1
Tin Finish—
Part Number 66084-2
Gold Finish—
Part Number 66084-3
Material
Phosphor bronze
Part Number
Extraction
Used with
Tool
Housings
480110-2, -5
480142-2, -3
582140-5
582147-5
582264-2
582500-2
582963-2
583167-3
465195-1
583280-1
583617-1
583680-1
583685-1
583722-1
583723-1
583724-1
583725-1
583726-1
465195-2
480133-2
Technical Documents
Instruction Sheet 408-7037
Note: All part numbers are RoHS compliant.
91
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Standard Blind-Mate Drawer Connectors
Cable Mounted Products
Product Facts
■
Designed for rack and panel
applications
■
Durable—withstands
multiple mating/unmating
■
Low insertion and
withdrawal force
■
Hermaphroditic contacts
■
Accepts signal and power
contacts
■
Provides excellent creep
distance
■
Mated connectors
dust-proof
■
Configurations available
in 8, 12, 16, 20 and 24
positions
■
Contacts accept wire sizes
24-14 AWG [0.2-2.0 mm2]
■
Accept wire insulation
diameter — .059-.154
[1.5-3.9]
■
Recognized under the
Component Program
of the Underwriters
Laboratories Inc.
R
Drawer connectors are
designed as an economical
rack and panel connector.
They are used in copying
machines, control panels,
power distribution boards,
industrial equipment, power
supplies and other electronic equipment.
Blind-mate drawer connectors feature excellent
durability and provide low
insertion and withdrawal
force. Leaf-type hermaphroditic contacts ensure
reliable, positive contact.
Contacts are on .197 [5.00]
centerlines for signal circuits, and .260 [6.60] centerlines for power circuits
(2-circuits at each end of
the double row of contacts)
for a total of 4. Row-to-row
spacing is .390 [9.90].
Housings are made of UL
94V-0 rated thermoplastic
and feature molded-in
guide pins and sockets for
positive connector mating.
Other features include wire
outlets which provide for
sufficient creep distance,
plus mated assemblies are
completely dust-proof.
Additional economies are
achieved through the use of
strip-form contacts suitable
for high-speed automatic
machine terminations. For
prototype, maintenance and
repair applications, contacts are available in loose
piece for easy termination
with Tyco Electronics hand
crimping tools.
Performance Specifications
Voltage Rating — 250 VAC
Current Rating —
4 Amps — 24 AWG [0.2 mm2] Wire
5 Amps — 22 AWG [0.3-0.4 mm2] Wire
7 Amps — 20 AWG [0.5-0.6 mm2] Wire
8 Amps — 18 AWG [0.8-0.9 mm2] Wire
12 Amps — 16 AWG [1.25-1.4 mm2]
Wire
15 Amps — 14 AWG [2.0 mm2] Wire
Contact Resistance —
10 milliohms max. (Initial)
20 milliohms max. (Final)
Insulation Resistance —
5000 milliohms min. (Initial)
2000 milliohms min. (Final)
Dielectric Withstanding Voltage —
2000 VAC/1 minute
Operating Temperature —
–20°C to +120°C (Includes T-Rise)
Insertion/Extraction Force —
Insertion—4 kg max. (Initial) —
16-position
Extraction—0.7 kg min. (Initial) —
16-position
Durability —
Tested to 1000 Mate/Unmate cycles
92
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Standard Blind-Mate Drawer Connectors (Continued)
Plug Connectors,
PCB-Mount
.524
[13.30]
Material and Finish
Circuit No.
.260
[6.60]
1.280
[32.5]
.984
[25.0]
Last Circuit No.
5.0xE=D
.197
[5.00]
C
B
A
Cable Mounted Products
Housing — Glass-filled polybutylene
terephthalate (PBT), blue, 94V-0 rated
Contacts — Phosphor bronze, plated
gold in contact area over nickel underplating; board-mount tails are brass,
plated tin over steel underplating
1.035
[26.3]
Related Product Data:
Performance Specifications —
page 92
Mating Receptacles — page 94
.260
[6.60]
Technical Documents
Product Specification
108-5125
Application Specification
114-5044
No. of
Pos.
8
12
16
Dimensions
B
C
1.500
1.055
38.0
26.8
1.890
1.449
48.0
36.8
2.283
1.843
58.0
46.8
A
2.016
51.2
2.409
61.2
2.803
71.2
D
.197
5.00
.591
15.0
.984
25.0
E
Plug Connector
Part Numbers
1
172653-2
3
172653-3
5
172653-1
Note: To ensure proper contact alignment, connectors must be mated during
the soldering process.
.027±.003
[0.68±0.08]
.169±.012
.197±.003
[5.00±0.08]
.315±012
[8.00±0.30]
[4.30±0.30]
Dia.
(2 Plcs.)
.390±.003
[9.90±0.08]
.390±.003
[9.90±0.08]
.524±.012
[13.3±0.30]
.260±.003 .059±.005
[6.60±0.08] [1.50±0.13]
Dia. (Typ.)
.260±.003
[6.60±0.08]
.197±.003
[5.00±0.08]
Recommended PC Board Layout
Note: All part numbers are RoHS compliant.
93
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Standard Blind-Mate Drawer Connectors (Continued)
Housings for Crimp
Snap-In Contacts
.756
[19.2]
.984
[25.0]
Material
.260
[6.60]
.524
[13.3]
.559
[14.2]
Polybutylene terephthalate (PBT), blue,
94V-O rated
D
Related Product Data
A
Performance Specifications —
page 92
Crimp Snap-In Contacts — page 95
Panel Cutout—page 95
Cable Mounted Products
1.035
[26.3]
C
B
5xE=F
.260
[6.60]
.886
[22.5]
Technical Documents
Product Specification
108-5125
Application Specification
114-5044
.197 Pitch
[5.60]
Floating
Bushing
Receptacle
.984
[25.0]
.886
[22.5]
.559
[14.2]
D
.756
[19.2]
C
A
B
.524
[13.3]
1.035
[26.3]
Plug
Dimensions
C
D
No. of
Pos.
A
B
8
1.858
47.20
1.055
26.80
2.016
51.20
2.252
57.20
1.449
36.80
16
2.657
67.20
Receptacle
E
F
1.500
38.00
1
.197
5.00
2.410
61.20
1.890
48.00
3
1.843
46.80
2.803
71.20
2.283
58.00
5
.984
25.00
20
3.039
77.20
2.236
56.80
3.197
81.20
2.677
68.00
7
1.378
35.00
24
3.433
87.20
2.630
66.80
3.591
91.20
3.071
78.00
9
1.772
45.00
12
.591
15.00
Floating
Bushing Size
.118
3.00
.157
4.00
.118
3.00
.157
4.00
.118
3.00
.157
4.00
.157
4.00
.118
3.00
.157
4.00
Plug
Part
Panel-Mount
Numbers Hole Diameter
.130
5172070-1
3.30
.169
5172070-3
4.30
.130
5172069-1
3.30
.169
5172069-3
4.30
.130
5172068-1
3.30
.169
5172068-3
4.30
.169
5173033-3
4.30
.130
5172625-1
3.30
.169
5172625-3
4.30
Part
Numbers
172063-1
172063-3
172061-1
172061-3
172059-1
172059-3
173032-3
172624-1
172624-3
Note: All part numbers are RoHS compliant.
94
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Standard Blind-Mate Drawer Connectors (Continued)
Crimp Snap-In Contacts
(Hermaphroditic)
.126
[3.20]
Material and Finish
Phosphor bronze, plated gold in contact
area (for length of .236 [6.0] from tip),
with entire contact underplated nickel
.791
[20.1]
Performance Specifications —
page 92
Housings — page 94
.146
[3.70]
Cable Mounted Products
Related Product Data
CERTI-CRIMP Hand Tool
Part Number 91591-1
Technical Documents
Instruction Sheets
408-097J, 408-098J, 408-151J
Wire Size Range
Insulation
Dia. Range
AWG
mm2
24-20
0.2-0.6
20-16
0.5-1.4
18-14
0.8-2.0
Part Numbers
Applicator for
AMP-O-LECTRIC
Loose Piece
Machine*
Contact
Strip Form
.059-.077
1.50-1.95
.071-.130
1.80-3.30
.091-.154
2.30-3.90
Hand Tool
Numbers
170311-1
170313-1
567324-2
91591-1
170484-1
170485-1
567241-2
91590-1
170312-1
170314-1
567325-2
2063849-1
*Applicators are for Model “K” machines. Consult Tyco Electronics for applicators for other bench machines and leadmaking machines.
Notes: 1. For applicable wire, use wire specified in UL 1015 or 1007.
Notes: 2. Contacts for 18-14 AWG [0.8-2.0 mm2] wire are used at the four corners of the connector as power contacts (8 required per assembly).
Extraction Tool Part Number 723986-1
Recommended Panel Cutout
.209±.012
[5.30±0.30]
(2 Plcs.)
.106±.012
[2.70±0.30]
(2 Plcs.)
No. of
Pos.
8
±.012
L[±.0.30]
J
±.012
K[±.0.30]
12
.008
[0.20R]
Max.
16
20
.169±.012
[4.30±0.30] or
.209±.012
[5.30±0.30] Dia.
(2 Plcs.)
.524±.012
[13.30±0.30]
24
Rear Panel-Mount Dimensions
J
K
L
1.913
1.500
1.110
48.60
38.00
28.20
2.307
1.890
1.504
58.60
48.00
38.20
2.701
2.283
1.898
68.60
58.00
48.20
3.094
2.677
2.291
78.60
68.00
58.20
3.488
3.071
2.685
88.60
78.00
68.20
.209
[5.30]
.941±.012
[23.90±0.30]
Rear Panel-Mount
Note: Mounting holes of .209 [5.30] dia. are used when mounting receptacle housings with .157 [4.0] long floating
bushings and the mating plug housings. Panel thickness is .063 [1.60]. Panel cutout shown above is for use
with plug housings. For receptacle housings, use the mirror-image cutout.
Note: All part numbers are RoHS compliant.
95
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Mini-Drawer Connectors
Cable Mounted Products
Product Facts
■
Combine signal circuits and
power circuits into one
connector
■
Power circuits can be used
for high current of up to 15A
■
Signal circuits accept CT
connector in the back,
reducing harnessing costs
■
Power circuits use crimptype tab and receptacle
contacts
■
Meet requirements for
creepage distance and
spatial distance for
primary power supply as
set forth in IEC-950,
safety specifications
for business machines
and OA equipment.
Creepage distance on active
power side: 5 mm
Spatial distance on active
power side: 4.5 mm
Technical Documents
Product Specification
108-60022
Application Specification
114-5182
Hybrid mini-drawer
connectors are designed
for use in rack and panel
application to serve as an
I/O connector for copying
machines, laser-beam
printers and other OA
equipment. They provide
an economical means of
combining into one
connector signal circuits
and power circuits which
were packaged separately
in the past.
A major design feature of
these hybrid mini-drawer
connectors is that minidrawer connectors mate
with one another on the
connector mating side and
in the back, signal circuits
accept a pre-terminated CT
receptacle connector.
Also, for power circuits,
crimp-type power contacts
are used by inserting them
into the four corners of the
mini-drawer connector.
The housing has an
integrated guide-pin and
socket to facilitate mating
of the connector halves.
Provision is also made to
prevent dust from entering.
This product line includes:
■ 12-position connector
(4 positions for power
and 8 positions for
signal circuits)
■ 24-position connector
(4 positions for power
and 20 positions for
signal circuits)
■ 32-position connector
(4 positions for power
and 28 positions for
signal circuits)
Performance Data
Voltage Rating —
250V AC (power)
30V AC (signal)
Current Rating —
15A max. (power)
2A max. (signal)
Contact Resistance —
10 mm Ω max. (power)
40 mm Ω max. (signal)
Insulation Resistance —
100M Ω max.
Dielectric Withstanding Voltage —
1.8KV AC/min. (power)
1.0KV AC/min. (signal)
Durability — 3,000 cycles min.
Drawer connectors are
available in the following
types depending on
application: (For details
contact our sales
department)
■ Mini-drawer connectors
■ Standard drawer
connectors
■ High current drawer
connectors
96
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Mini-Drawer Connectors (Continued)
Standard Width
Plugs
Cable Mounted Products
Receptacles
Type
Plug
Receptacle
Plug
Receptacle
Part
Number
292180-1
292184-1
1-292183-2
1-292186-2
Number of
Power Contacts
2
2
6
6
Number of
Signal Contacts
4
4
12
12
1.299
1.299
2.638
2.638
Part
Number
1-292187-2
2-292190-2
3-292187-2
4-292190-2
2-292189-3
1-292192-3
Number of
Power Contacts
3
3
4
4
3
3
Number of
Signal Contacts
5
5
5
5
7
7
1.870
1.713
2.146
1.988
2.028
1.870
L
[33.00]
[33.00]
[67.00]
[67.00]
W
.646
.646
.748
.748
[16.40]
[16.40]
[19.00]
[19.00]
Slim Width
Plugs
Receptacles
Type
Plug
Receptacle
Plug
Receptacle
Plug
Receptacle
L
[47.50]
[43.50]
[54.50]
[50.50]
[51.50]
[47.50]
W
.591
.472
.531
.472
.591
.472
[15.00]
[12.00]
[13.50]
[12.00]
[15.00]
[12.00]
Note: All part numbers are RoHS compliant.
97
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Mini-Drawer Connectors (Continued)
Power Contacts
Material
Copper alloy
For finish, see table below.
Finish Codes
Cable Mounted Products
1) Over nickel underplated, contact area:
gold plated, crimp area: tin plated
2) Tin plated all over.
Hand Tool AWG #20-24
Part No. 934199-1 (411-5662)
AWG #16-20
Part No. 934198-1 (411-5661)
Receptacle
Wire Range
AWG
mm2
Tab
Wire
Ins. Dia.
24-20
0.2-0.5
1.4-2.6
20-16
0.5-1.25
1.6-2.8
Plating
Code
1
2
1
2
Receptacle Part Number
Strip Form
179317-2
1-179317-2
179316-2
1-179316-2
Tab Part Number
Strip Form
179322-2
1-179322-2
179321-2
1-179321-2
Receptacle Assembly
Material and Finish
Housing — Thermoplastic, black
Contact — Copper alloy, gold plated
on mating side over nickel underplate,
tin plated on CT mating side over nickel
underplate.
Section X-X
Section Y-Y
No. of Pos.
(Power/
Signal)
A
B
C
D
E
F
G
H
Mini-Drawer
Receptacle
Assembly Part No.
Required
Number of
Power Contact
Required
Number of
CT Connector
12 (4-8)
24 (4-20)
32 (4-28)
56.0
68.0
76.0
47.0
59.0
67.0
6.0
18.0
26.0
24.1
36.1
44.1
31.8
43.8
51.8
31.4
43.4
51.4
38.0
50.0
58.0
32.4
44.4
52.4
292185-8
2-292185-0
2-292185-8
4
4
4
4 Pos. x 2
10 Pos. x 2
14 Pos. x 2
Dimensions
Note: All part numbers are RoHS compliant.
98
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Mini-Drawer Connectors (Continued)
Plug Assembly
Material and Finish
Housing — Thermoplastic, black
UL94V-0
Contact — Copper alloy, gold plated
on mating side over nickel underplate,
tin plated platen on CT mating side over
nickel underplate.
Cable Mounted Products
No. of Pos.
(Power/
Signal)
A
B
C
D
E
F
G
12 (4-8)
24 (4-20)
32 (4-28)
56.0
68.0
76.0
47.0
59.0
67.0
6.0
18.0
26.0
24.1
36.1
44.1
36.0
48.0
56.0
31.4
43.4
51.4
33.4
45.4
53.4
H
Mini-Drawer
Receptacle
Assembly Part No.
Required
Number of
Power Contact
Required
Number of
CT Connector
38.0
50.0
58.0
292182-8
2-292181-0**
2-292181-8
4
4
4
4 Pos. x 2
10 Pos. x 2
14 Pos. x 2
Dimensions
*12-Position connector is provided with sequential feature in one power circuit position. Other connector sizes have sequential feature in power circuits and
signal circuits.
**Optional part numbers offer sequential mating – see customer drawings for details.
Note: All part numbers are RoHS compliant.
99
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Mini-Drawer Connectors (Continued)
CT Receptacle Connectors
to Mate with Signal Circuit
Terminator with Insulation
Displacement Contacts
Receptacle Assemblies
(Wire Application Side)
Material and Finish
Cable Mounted Products
Housing — UL94V-0 rated, glassfilled P.B.T. see chart below for color.
Contact — Pre-tinned phosphor
bronze
Wire Size — AWG #28-26
(0.08-0.15 mm2)
Insulation Dia. — 0.85-1.05 mm
Wire Size — AWG #24
(0.20-0.22 mm2)
Insulation Dia — 0.95-1.05 mm2
(For AWG #24 wire, see notes under the
table)
4-15 Positions
Dimensions
No. of
Positions
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
B
4.8
6.8
8.8
10.8
12.8
14.8
16.8
18.8
20.8
22.8
24.8
26.8
28.8
30.8
C
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
30.0
32.0
3 Position
2 Position
Part Number
Receptacle Assembly**
AWG #28-26*
AWG #24***
173977-2
2-179694-2
173977-3
2-179694-3
173977-4
2-179694-4
173977-5
2-179694-5
173977-6
2-179694-6
173977-7
2-179694-7
173977-8
2-179694-8
173977-9
2-179694-9
1-173977-0
3-179694-0
1-173977-1
3-179694-1
1-173977-2
3-179694-2
1-173977-3
3-179694-3
1-173977-4
3-179694-4
1-173977-5
3-179694-5
* The color of housing is natural. Other colors available include blue, yellow and black. For details contact our Sales
Department
** For wire to be used, contact our Sales Department as there are wires that have been tested by Tyco Electronics
and can be recommended for your use.
*** The color of housing is gray.
Note: All part numbers are RoHS compliant.
100
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Hybrid Mini-Drawer Connectors (Continued)
CT Receptacle Contacts to
Mate with Signal Circuit
Termination with Crimp
Type Contacts
Receptacle Contact
Wire Size
AWG (mm2)
Insulation Dia.
(mm)
30-26
(0.05-0.12)
26-22
(0.12-0.35)
0.65-1.35
0.93-1.5
Material
and Finish
Phosphor bronze
(0.20 mm thickness),
tin plated
Strip Form
Part Number
Loose Piece
179609-1
—
179227-1
179518-1
Hand Tool
234169-1
(411-5711)
91572-1
(408-8547)
Note: Loose piece contacts, being small in size, are supplied in the form of a comb with 10 pieces on 7.5 mm pitch.
There is a slit at the root of each contact and it can be snapped off easily.
Cable Mounted Products
2 Position
3 Position
Receptacle Housing
Material
UL94-0 rated, 66 nylon, natural color
(white)
4 Position
4-15 Positions
No. of
Positions
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Dimensions
A
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
B
4.8
6.8
8.8
10.8
12.8
14.8
16.8
18.8
20.8
22.8
24.8
26.8
28.8
30.8
C
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
30.0
32.0
Part Number
Receptacle Assembly*
179228-2
179228-3
179228-4
179228-5
179228-6
179228-7
179228-8
179228-9
1-179228-0
1-179228-1
1-179228-2
1-179228-3
1-179228-4
1-179228-5
* The color of housing is natural. Other colors available include blue, yellow and black. For details contact our Sales
Department
Note: All part numbers are RoHS compliant.
101
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ET Power Connector
Cable Mounted Products
Product Facts
■
Right-angle and vertical
mounts available
■
Low profile right-angle
connector ≤ 8 mm above pcb
■
2.5 mm2 (14 AWG) to 6 mm2
(10 AWG) wire range
■
Refer to current v temp rise
graphs for current capability
■
Coding contacts for sense
function
■
Positive metal latch
retention
■
Up to 30 Amps per contact.
See temperature rise charts
on page 103
Description
■
Cable to pcb
■
Low profile Right Angle
■
Vertical Mount
■
High reliability interface
■
Excellent price to
performance ratio
Designed for low-profile
power distribution units
requiring small form factor
connector with high current,
the ET power connector is a
low loss, highly reliable and
cost effective solution for
cable-to-pcb applications.
The connector is available
in both a vertical mount and
a right-angle mount, which
stands at just 8 mm off of
the board. A unique feature
of the ET power series is
integrated coding contacts
which allow different
electronic functions such
as sense and enable to be
designed into the PDU
electronics with activation
on full insertion of the cable
connector.
Crimp contacts from the
industry proven “Standard
Power Timer” range for
use with 2.5 mm2 (14 AWG),
4 mm2 (12 AWG) and 6 mm2
(10 AWG) wire.
The cable connector
has a positive latching
mechanism providing no
accidental un-mating even
with pull forces up to 100N.
Material and Finish
Housing ST Cable — Black glassfilled thermoplastic, UL 94V-0 rated
Latch — Stainless Steel
Housing ST & Right-angle PCB —
Black glass-filled thermoplastic,
UL 94V-0 rated
Power Contacts — Copper alloy,
3.0 µm Ag min.
Contact Detection — 0.8 µm gold
min. in contact place; 1.27 µm nickel
min. contact place
Application
■
Power Distribution
■
Power Supplies
■
Telecoms Base Stations
■
Computer Servers and
Storage Systems
■
Industrial Electronic
Equipment Cabinets
Technical Documents
Product Specification
108-19346
Application Specification
114-19110
102
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ET Power Connector (Continued)
Test Results
Temperature Rise vs.
Current Results
Temperature Rise Vs. Current
2.5mm2 Wire
T
80
70
60
50
40
30
Cable Mounted Products
20
10
0
5
0
10
20
I [A]
25
30
35
40
30
35
40
Temperature Rise Vs. Current
5mm2 Wire
T
50
15
45
40
35
30
25
20
15
10
5
0
0
5
10
25
20
I [A]
Temperature Rise Vs. Current
6mm2 Wire
T
50
15
45
40
35
30
25
20
15
10
5
0
0
5
10
15
20
25
30
35
40
45
I [A]
Contact Summary
.260
[6.60]
Refer to Standard Timer
catalog 889759 for detailed
information or Product/
Application Specification.
Material
.189
[4.80]
Plating — Silver
.016
[0.40]
Wire Size
Range mm2
0.2 – 0.5
0.5 – 1.0
>1.0 – 2.5
>2.5 – 4.0
>4.0 – 6.0
Part
Number
927840-4
927831-4
927837-4
927829-5
963709-5
.098
[2.50]
.016
[0.40]
.130
[3.30]
.177
[4.50]
.177
[4.50]
Technical Documents
Product Specification
108-18025
Application Specification
114-18037
Note: All part numbers are RoHS
compliant.
103
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
ET Power Connector (Continued)
ET Power Cable Connector
Material and Finish
Cable Mounted Products
Housing — Thermoplastic,
UL 94V-0 rated
Latch — Stainless Steel
Part Number 1982299-1
With Right Coding Key Only
Part Number 1982299-2
With Left Coding Key Only
Part Number 1982299-3
With Two Coding Keys
Part Number 1982299-4
Without Coding Keys
Right-Angle PCB Header
Material and Finish
Housing — High temperature liquid
crystal polymer, UL 94V-0 rated
Contacts — Silver plated copper alloy
Part Number 1982295-1
With Coding Contacts
Part Number 1982295-2
Without Coding Contacts
Part Number 2042274-1
With Coding Contacts
Part Number 2042274-2
Without Coding Contacts
Vertical PCB Header
Material and Finish
Housing — High temperature liquid
crystal polymer, UL 94V-0 rated
Contacts — Silver plated copper alloy
Note: All part numbers are RoHS
compliant.
104
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC PL Connectors
Product Facts
Wire to board connection
system
■
Improved dual-action
contact design — provides
better contact lead-in and
reduces contact mating
force
■
Sequenced contacts
available for mate-first
break-last operation
■
4-, 6- and 12-position
right-angle headers and
free hanging receptacles
■
4.2 mm x 5.5 mm centerline
■
Receptacle contacts
designed for 26-16 AWG
stranded wire
■
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
Cable Mounted Products
■
R
■
Certified by Canadian
Standards Association,
File No. LR7189
Technical Documents
Product Specification
108-1646
Application Specification
114-6067-Crimping Contacts
Qualification Test Report
501-394
Performance Data
Voltage Rating — 600 VAC
Current Rating — 9 Amps maximum
in 2-position application
Low Level Resistance —
10 megohms max.
Dielectric Withstanding Voltage —
1500 VAC/min.
Insulation Resistance —
1000 Megohms minimum
Operating Temperature —
-55°C to + 105°C [-67°F to +221°F]
R
The latest addition to the
4.2 mm Wire-to-Board
Power Connectors is the
AMP-DUAC PL Connector.
This product uses the
industry proven AMP-DUAC
contacts with the addition
of several housing improvements to offer significant
overall improvements in
connector reliability. The
product is available in both
component form and as
fully assembled custom
cable assemblies.
The AMP-DUAC PL
housings are designed to
confirm that all electrical
contacts are fully seated.
The “PL” refers to “Positive
Locking” of the contacts.
It is also referred to as
terminal position assurance.
Contacts are inserted into
the receptacle housing and
the contact lock is installed
to lock all the contacts into
position. If any one of the
contacts is not fully inserted,
the contact lock cannot
be installed. This feature
eliminates a common
concern of operator fatigue
and the resulting contact
back-out, which occurs
when a contact is not
installed properly. An
improved mounting flange
has also been added for
more secure printed circuit
board mounting.
Finally, the housings
have been re-designed to
provide an improved latch,
which offers a metal spring
instead of the original
plastic spring/latch. An
extended latch arm is also
available for hard to reach
installations or where the
connectors are stacked in
close proximity.
All the housings are
polarized to help prevent
mis-mating.
105
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC PL Connectors (Continued)
AMP-DUAC PL
PCB Headers
Material
Cable Mounted Products
Housings — Nylon, UL 94V-0
Color, white
Contacts — Brass, tin-lead
Finish — 0.00038 [0.00030] gold in
mating area, tin-lead in solder tail, all
over 0.00127 [0.000050] nickel
Recommended Mounting Hole Pattern
For 1.78 Max. Thick PC Board
Component Side Shown
No. of
Positions
Mate-First
Break-Last
Position #
Part
Number
4
All Standard
Length 3
6
All Standard
Length 3
12
All Standard
Length 4
5794172-2
5794172-3
5794173-2
5794173-3
5794176-2
5794176-3
Note: All part numbers are RoHS compliant.
106
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC PL Connectors (Continued)
AMP-DUAC PL Receptacles
Completed Assembly
Material
Housings — Nylon, UL94V-0
Color, White
Technical Documents — page 105
Contacts — page 113
Position Lock
Cable Mounted Products
Receptacle Connector
L
.384
[9.76]
Ref.
.077 ± .002
[1.95 ± 0.05]
2 Plcs.
.772
[19.60]
Ref.
.348
[8.85]
Ref.
.134
Ref.
[3.40]
.469
[11.90]
.594 ± .004
[15.10 ± 0.10]
.327
[8.30]
Standard Latch
Assembly
Extended Latch
Assembly
No. of
Positions
Dimension
L
Housing
4
6
12
15.9
20.1
28.6
794152-1*
794153-1
794156-1
Part Numbers
Housing with
Standard Latch
Positive Lock
794318-1
794319-1
794150
794322-1
Extended Latch
794149
*Latch items ordered separately
Optional keying plug — Part No. 794144-1
Note: Position Lock Required — use one per housing — Part No. 794145-3
Note: All part numbers are RoHS compliant.
107
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC PL-II Connectors
Cable Mounted Products
Product Facts
■
Wire-to-board connection
system combining power
and signal contacts
■ 10A power contacts
■ 4A signal contacts
■
High conductivity copper
alloy power contacts yield
30% gain in current carrying
capacity compared to
alternative designs
■
Dual action contact design —
reduces mating forces by
up to 50% compared to
alternative designs
■
9 power and 20 signal
contacts
■
Positive Lock (PL) feature
on both power and signal
contacts ensures contacts
remain in position in cable
receptacle
■
Pin and receptacle contacts
offered in three sizes:
■ 16 AWG
■ 18 AWG
■ 20-22 AWG
■
Wide 5.2 X 5.5 mm contact
spacing allows for 300V
applications.
■
Recognized under the
Component Program of
Underwriters Laboratories
Inc., File No. E28476
®
C
US
The AMP-DUAC PL-II
Connectors bring both
shielding and a power /
signal mix to the popular
AMP-DUAC product family.
In addition, the wider contact spacing and the use of
high conductivity materials
results in a higher current
carrying capacity than
the original 4.2 mm pitch
AMP-DUAC product.
The deep back shell allows
for gathering the larger wire
and insulation diameters
involves with combination
power / signal and shielding all in the same cable.
Traditional signal connectors do not accept the
range of wire sizes covered
by the AMP-DUAC PL-II
product.
For applications involving
higher voltage cabled power
distribution, this product is
the ideal solution. The
AMP-DUAC PL-II connector
uses the original industry
proven dual-action contact
design which provides a
lower mating force and less
plating wear than alternate
contact designs. The signal
contacts also feature a
twin-cantilever beam that
mates on the milled contact
surface to provide low
plating wear and high longterm reliability.
The cable mounted
receptacle uses the popular
“Positive Lock” devices
proven throughout the
automotive industry to
ensure all the contacts are
fully seated. The “positive
locks” are also referred to
as “terminal position
assurance”. If any one of
the contacts is not properly/
completely installed into the
housing, then the “Positive
Lock” can not be installed.
This feature reduces the
common concern of operator fatigue and the resulting
contact back-out which
occurs when a contact is
not properly seated.
Technical Documents
The shielding system fully
encapsulates the inner
conductors and cable braids
and provides a reliable
conduction to the faceplate
of the mating equipment.
Materials
Product Specification
108-2218
Application Specification
Contact Tyco Electronics
Performance Data
Voltage Rating — 600 VAC
Current Rating —
10 Amps max on a single contact
6 Amps on each contact in 48 pos.
connector
Low Level Resistance —
10 milliohms max
Insulation Resistance —
1000 Megohms minimum
Operating Temperature —
-40°C to +105°C
Housing Material — PBT, UL 94V-0
Colors —
Plugs and Receptacles — Black
Positive Locks — White
Finally, the cable retention
is accomplished through
two rear-accessed over
molded jackscrews for easy
installation and removal.
108
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC PL-II Connectors (Continued)
PCB Plug
Part Number 6469602-3
1.161
Ref.
[29.50]
1.268
Ref.
[32.20]
Cable Mounted Products
1.740
Ref.
[44.20]
.574
[14.58]
Ref.
.157
Ref.
[4.00]
.736
Ref.
[18.70]
Positive Lock For Signal
Contacts Sold Separately
Ref. Part Number 1600902-1
Shield
Part Number 1469609-2
Free-Hanging Receptacle
Shown with Positive Locks
Part Number 1469606-1
Note: Other cable components required.
Cable receptacle components shown not
sold separately. Receptacle only sold as
part of a finished cable assembly.
Cable Clamp
Part Number 1469610-1
Note: All part numbers are RoHS compliant.
109
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC UPC Connectors
Cable Mounted Products
Product Facts
■
Wire-to-wire connection
system
■
High conductivity copper
alloy contacts yield 30%
gain in current carrying
capacity compared to
alternative designs
■
Dual action contact design —
reduces mating forces by up
to 50% compared to
alternative designs
■
Sequenced contacts for
make-first-break-last
operation
■
48 and 66 position housings
■
4.4 mm X 5.3 mm contact
grid
■
Pin and Receptacle contacts
offered in three sizes:
■ 16 AWG
■ 18 AWG
■ 20-22 AWG
■
Recognized under the
Component Program of
Underwriters Laboratories
Inc., File No. E28476
®
C
US
The latest addition to the
AMP-DUAC product family
is the AMP-DUAC UPC
connector. The UPC connector offers much higher
pin counts and a variety of
product improvements to
make the connector more
reliable and easier to use.
The UPC connector uses
the original industry proven
dual-action contact design
along with very high conductivity copper alloys to
improve the current
carrying capacity.
The first noticeable difference of the UPC connector
is the large pin count. With
either 48 or 66 positions,
the housing can serve as a
common mating I/O point
where multiple low current
power connector cables are
combined into one interface.
Other connectors would
yield an excessive mating
force when mating this
number of wires, however,
the low mating force of the
AMP-DUAC / UPC connector allows up to 66 wires to
be mated with less than a
20 lb mating force.
The next key improvement
is the use of molded-in
guide pins. The guide pins
make the mating process
very easy and provide a
visual polarization of the
connector. The housings
mate together easily.
The use of two locking
latches provides a more
secure connection and the
screw-mounts for the panel
mounted plug provide better
retention than plastic
latches.
Finally, the free-hanging
receptacle uses the popular
“Positive Lock” device to
confirm all the contacts are
fully seated. The “positive
locks” are also referred to
as “terminal position assurance”. If any one of the
contacts is not properly/
completely installed into the
housing, then the “Positive
Lock” can not be installed.
This feature eliminates the
common concern of operator fatigue and the resulting
contact back-out which
occurs when a contact is
not properly seated.
Technical Documents
Product Specification
108-2248
Application Specification
114-13195
Performance Data
Voltage Rating — 600 VAC
Current Rating —
11 Amps max on a single contact
4 Amps on each contact in 48 pos.
connector
Low Level Resistance —
10 milliohms max
Insulation Resistance —
1.2 E16 ohms minimum
Operating Temperature —
-40°C to +105°C
Materials
Housing Material — PBT, UL 94V-0
Colors —
Plugs and Receptacles — Black
Positive Locks — White
110
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
AMP-DUAC UPC Connectors (Continued)
Cable Mounted Products
C
B
A
1.476
Ref.
[37.50]
1.280 ± .005
[32.50 ± 0.13]
.984 ± .005
[25.00 ± 0.13]
Panel-Mount Plug
(Accepts contacts on page 112)
1.449 ± .008
[36.80 ± 0.20]
1.512
Ref.
[38.40]
1.280 ± .008
[32.50 ± 0.20]
1.606
Ref.
[40.78]
Free-Hanging Receptacle
(Accepts contacts on page 113)
Size
(No. Circuits)
Panel-Mount
Plug
48
1934142-1
66
1934143-1
A
1.61
41.0
2.13
54.2
Dimensions
B
1.85
47.0
2.37
60.2
C
2.22
56.4
2.74
69.6
Free-Hanging
Receptacle*
Positive
Lock*
1934144-1
1469910-1
1934145-1
1934017-1
*Two (2) required for each receptacle housing. Not used in plug housings.
Additional configurations possible. For information, please contact your Tyco Electronics sales engineer.
Note: All part numbers are RoHS compliant.
111
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Contacts for AMP-DUAC PL, PL-II and UPC Connectors
Materials — High Conductivity
Copper Alloy
Finish — Pre-Tin or Gold Plated
Cable Mounted Products
.666 ± .008
[16.91 ± 0.20]
Contacts, Male
Technical Documents
Product Specification
108-2248 AMP-DUAC UPC
Application Specification
114-6067 AMP-DUAC PL
114-13195 AMP-DUAC UPC
AMP-DUAC PL or UPC Contacts
Wire Size
Range
AWG [mm2]
22-20
[0.3-0.5]
18 or 18+22
[0.8-1.1]
16 or 2 @ 18
[1.3-1.6]
Ins. Dia.
Range
Plating
Part Number
(Continuous Strip)
Applicator
.590–.094
[1.50–2.40]
.087–.154
[2.20–3.90]
.098–.173
[2.50–4.40]
Gold
794576-4
680308-3
Gold
1934185-4
1852467-3
Gold
1934184-4
1852468-3
Application Equipment: Extraction Tool 1976132
*Made from Phosphor-Bronze material (low conductivity)
Note: All part numbers are RoHS compliant.
112
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Contacts for AMP-DUAC PL, PL-II and UPC Connectors (Continued)
Materials — High Conductivity
Copper Alloy
Finish — Gold Plated
.583 ± .002
[14.80 ± 0.05]
Cable Mounted Products
Contacts, Female
Technical Documents
Product Specification
108-2248 AMP-DUAC UPC
Application Specification
114-6067 AMP-DUAC PL
114-13195 AMP-DUAC UPC
AMP-DUAC PL or UPC Contacts
Wire Size
Range
AWG [mm2]
22-20
[0.3-0.5]
18 or 18+22
[0.8-1.1]
16 or 2 @ 18
[1.3-1.6]
Ins. Dia.
Range
Plating
Part Number
(Continuous Strip)
Applicator
.590–.094
[1.50–2.40]
.087–.154
[2.20–3.90]
.098–.173
[2.50–4.40]
Gold
1934193-4
1852469-3
Gold
1934183-4
1852467-3
Gold
1934182-4
1852468-3
Application Equipment: Extraction Tool 1976382
Note: All part numbers are RoHS compliant.
113
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
Power Connectors & Interconnection Systems
Other Soft Shell Pin & Socket Connectors
Cable Mounted Products
Micro MATE-N-LOK 3 mm Connector System
■
Wire-to-wire and wire-to-board, pin and receptacle connectors
■
3.0 mm [.118] centerline spacing
■
2-12 positions – single row
■
2-24 positions – dual row
■
Ratings: 5A, 250 VAC
■
Accommodates 30-20 AWG wire
■
Panel-mount or free-hanging versions
■
Dual beam receptacle contact design for improved reliability
■
PCB-mount pin header assemblies available in both vertical
and right-angle styles; surface-mount or through hole versions
■
Available in a low profile design (
工商网监
湘ICP备2023018690号
