3022-100-N

Model 3022 Accelerometer Piezoresistive MEMS DC Response Circuit Board Mountable Low Cost The Model 3022 is a silicon MEMS accelerometer in a Wheatstone bridge configuration. The accelerometer is packaged on a ceramic substrate with an epoxy sealed ceramic cover and is designed for adhesive mounting. The accelerometer is offered in ranges from ±2g to ±200g range and provides a flat frequency response to minimum 2000Hz. The silicon MEMS sensor is gas damped and incorporates overrange stops for high-g shock protection. Dimensions For a similar accelerometer designed for bolt mounting, see the Model 3028. FEATURES Adhesive Mounted ±0.5% Non-linearity Open Wheatstone Bridge DC Response Gas Damping Built-in Overrange Stops Low Power Consumption APPLICATIONS Vibration & Shock Monitoring Motion Control Impact & Shock Testing Modal Analysis Embedded Applications Machinery Model 3022 Rev C 32 Journey Ste. 150 Aliso Viejo, CA 92656 www.meas-spec.com 949-716-5377 01/09/2013 t&m@meas-spec.com Model 3022 Accelerometer Performance Specifications All values are typical at +24°C, 100Hz and 5Vdc excitation unless otherwise stated. Measurement Specialties reserves the right to update and change these specifications without notice. Measurement Specialties’ family of DC Response Embedded Accelerometers are used for vibration/shock monitoring, structural analysis, motion control, impact testing, and transportation study. These MEMS sensors feature internal gas damping and outstanding shock survivability. Parameters DYNAMIC Range (g) Sensitivity (mV/g)1 Frequency Response (Hz) Natural Frequency (Hz) Non-Linearity (%FSO) Transverse Sensitivity (%) Damping Ratio Shock Limit (g) Notes ±2 8.0-20.0 0-150 700 ±0.5 3 0.7 5000 ±10 3.0-6.0 0-400 1000 ±0.5 3 0.7 5000 ±20 1.5-3.0 0-600 1500 ±0.5 3 0.7 5000 ±50 0.6-1.5 0-1000 4000 ±0.5 3 0.7 5000 ±100 0.3-0.6 0-1500 6000 ±0.5 3 0.7 5000 ±200 0.15-0.3 0-2000 8000 ±0.5 3 0.6 5000 ±25 2 to 10 25006500 25006500 >100 10 ±25 2 to 10 25006500 25006500 >100 10 ±25 2 to 10 25006500 25006500 >100 10 ±25 2 to 10 25006500 25006500 >100 10 Differential Insulation Resistance (MΩ) Residual Noise (µV RMS) Ground Isolation ±25 ±25 ±25 2 to 10 2 to 10 2 to 10 2500250025006500 6500 6500 2500250025006500 6500 6500 >100 >100 >100 10 10 10 Isolated from Mounting Surface ENVIRONMENTAL Thermal Zero Shift (%FSO/°C) Thermal Sensitivity Shift (%/°C) Operating Temperature (°C) Compensated Temperature (°C) Storage Temperature (°C) -0.09 -0.09 -0.15 -0.15 -40 to +125 Not Compensated -40 to +125 -0.09 -0.15 -0.09 -0.15 -0.09 -0.15 -0.09 -0.15 Typical Typical ELECTRICAL Zero Acceleration Output (mV) Excitation Voltage (Vdc) Input Resistance (Ω) Output Resistance (Ω) ±5 6.0-15.0 0-250 800 ±0.5 3 0.7 5000 -0.09 -0.15 @5Vdc Excitation ±5% @50Vdc Maximum See Note 2 PHYSICAL Case Material Ceramic Weight (grams) 3.1 Mounting Adhesive or solder 1 Output is ratiometric to excitation voltage 2 Order model 3022-XXX-10254 for temperature compensation resistor values included in the calibration certificate. The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others. Ordering Info PART NUMBERING Model Number+Range+Electrical Connection 3022-GGG-P l l l l_____Electrical Connection (P=pins, N=solder pads) l___________Range (010 is 10g) Example: 3022-010-P Model 3022, 10g, Pins Model 3022 Rev C 32 Journey Ste. 150 Aliso Viejo, CA 92656 www.meas-spec.com 949-716-5377 01/09/2013 t&m@meas-spec.com