365225-000

SPECIFICATION CONTROL DRAWING 55A7238 Date THREE CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT TITLE Revision A 4-8-06 This specification sheet forms a part of the latest issue of Raychem Specification 55A. COMPONENT WIRES - 55A0213 JACKET - RADIATION-CROSSLINKED, MODIFIED ETFE SHIELD - TIN-COATED COPPER FILAMENT STRIPPING THREAD - NOMEX®, 200/I/4E, No finish CABLE CONSTRUCTION DETAILS PART NUMBER 1/ 55A7238-22-* 55A7238-20-* 55A7238-18-* 55A7238-16-* 55A7238-14-* 55A7238-12-* CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) 22 20 18 16 14 12 38 38 38 38 38 38 JACKET THICKNESS (inches) MINIMUM .006 .006 .006 .006 .007 .007 NOMINAL .008 .008 .008 .008 .009 .009 OUTSIDE DIAMETER (inches) NOMINAL .135 .152 .176 .191 .225 .264 MAXIMUM .142 .160 .185 .201 .236 .277 MAXIMUM WEIGHT (lb/1000 ft.) 17.4 23.5 32.5 39.0 56.5 81.0 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level ACCELERATED AGING: 300 ± 3°C for 7 hours BLOCKING: 200 ± 3°C for 6 hours DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz FLAMMABILITY: Procedure 1, 3 seconds (maximum); 3 in. (maximum); no flaming of facial tissue JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 50% (minimum) Tensile Strength, 5000 lbf/in² (minimum) JACKET FLAWS: Spark Test, 1000 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) LIFE CYCLE: 200 ± 3°C for 168 hours LOW TEMPERATURE-COLD BEND: -65 ± 3°C for 4 hours SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND TEST: (POST ENVIRONMENTAL) 1000 volts (rms), 60 Hz, l minute PART NUMBER: The "*" in the part numbers above shall be replaced by color code designators with a slash separating the component wire colors and a dash separating the component wires color from the jacket color. Colors shown do not necessarily reflect the sequence of manufacturing. Example: AWG 20, black, brown and red component wires; white jacket: 55A7238-20-0/1/2-9 NOTE: Nominal values are for information only. Nominal values are not requirements. NOMEX® is a registered trademark of E.I. du Pont de Nemours and Company. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. Page 1 of 1 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. R Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2006 Tyco Electronics Corporation. All rights reserved.