415314-1

COAXICON* 50-Ohm R.F. Connectors Series N Right-Angle Plugs Instruction Sheet 408-2028-5 19 MAY 09 Rev B The following instruction sheets contain information on additional N Series connectors: Center Contact Plugs Jacks Bulkhead Jacks Panel Jacks 408–2028–01 408–2028–02 408–2028–03 408–2028–04 Ferrule Right Angle Plug Body ÏÏÏÏ ÏÏÏÏ Reasons for reissue are provided in Section 3, REVISION SUMMARY. 2. TYPICAL ASSEMBLY PROCEDURE NOTE (Figure 2) Refer to the table on page 1 to determine the appropriate figure reference (Figure 3, 4, 5, or 6) i NOTE: This type ferrule contains a seal and is used on all for strip length dimensions. weatherproof connectors. 1. Slide ferrule on cable, then strip cable to appropriate dimensions. DO NOT comb braid. Figure 1 2. Crimp center contact onto center conductor using the appropriate tool instruction sheet referenced in table above. 1. INTRODUCTION 3. Insert cable with crimped center contact into the connector (see Figure 2A) making certain that braid passes over support sleeve (see Figure 2B). Pull back lightly on cable to ensure contact is retained. The connectors listed below are assembled and crimped as described in Section 2. Refer to the table below for tool instruction sheet numbers. RG/U CABLE SILVER PLATED PN Standard PN & Govt. Desig.{ M39012/ WeatherProof PN TARNISH RES. PN CABLE STRIP DIM. DIES FOR TOOL 69365 OR 69710 CRIMPING TOOL PN Instruction Sheet PN Instruction Sheet 8, 8A, 213 05-0002 225014-2 225389-2 225669-2 Fig. 4 220015-1 408-2331 - - 9, 9A, 9B, 214 05-0003 225014-3 225389-4 225669-1 Fig. 3 220015-1 408-2331 - - 165 - - 225389-8 - Fig. 4 220015-1 408-2331 - - 225 - - 225389-3 - Fig. 3 220015-1 408-2331 - - - - 225389-9 - Fig. 4 220015-3 408-2331 - - 58A, 58C - - 225394-4 - Fig. 5 220045-2 408-2336 220062-1 408-2345 55A, 223 - - 225394-1 - Fig. 5 220045-2 408-2336 220062-1 408-2345 142, 142A, - - 225394-2 - Fig. 5 220045-2 408-2336 220062-1 408-2345 MICRODOT 250-4172, -4208 142B { 393 - - 225389-6 - Fig. 3 220015-1 408-2331 - - 217 - 415314-1 - - Fig. 6 220065-1 408-2341 - - Government designation applies only to silver plated standard parts. E 2009 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 2 LOC B 408-2028-5 COAXICON 50-Ohm R.F. Connectors Series N Right-Angle Plugs NOTE The design of connectors for smaller cables (RG i pass beyond the internal locking feature if it is inserted with too much force. Pull back on the cable to properly locate and retain the contact in 12.70 [.500 " " [.688 .41 mm NOTE [.188 In.] Ref. 9.53 [.375 " " .41 mm Cut Dielectric .016 In.] Square NOTE: Not to Scale When terminating part to cables less than Figure 4 304.8 mm [12 in.] in length, care must be taken i to prevent the cable dielectric from moving inside the cable jacket during crimping. Failure to prevent this movement could lead to DWV failures. When short cable lengths are required, it length of cable and trim cable to final length after 10.31 crimping part onto cable. [.406 ÏÏÏ ÏÏÏ " " 15.09 is recommended to use a 304.8 mm [12 in.] A .41mm .016 In.] 4.78 mm .016 In.] the locking feature if this condition has occurred. 4. Slide ferrule over braid and crimp ferrule using the appropriate tool instruction sheet reference in table on page 1 (see Figure 2C). If using a weatherproof connector, make certain that the rubber seal is properly positioned, as shown in Figure 2D. " " 17.48 55, 58, 141, and 142) allows the center contact to " " [.594 .41 mm .41mm .016 In.] 4.78 mm .016 In.] [.188 In.] Ref. 8.74 Support Sleeve Crimped Center of Connector Contact Ferrule [.344 " " .41 mm Cut Dielectric .016 In.] Square NOTE: Not to Scale B ÏÏÏ ÏÏÏ ÏÏÏ ÏÏÏ C Figure 5 Braid Over Connector Support Sleeve " " 23.42 Slide Ferrule Forward Over Braid and Support Sleeve 13.89 [.547 Weatherproof Connector " " [.922 .41 mm .41mm .016 In.] 4.78 mm .016 In.] [.188 In.] Ref. D ÏÏÏ ÏÏÏ 12.70 [.500 " " Cut Dielectric Rubber Seal Square NOTE: Not to Scale Figure 2 " " 17.48 [.688 .41 mm Figure 6 .41mm .016 In.] 4.78 mm .016 In.] 3. REVISION SUMMARY [.188 In.] Ref. NOTE: Not to Scale Cut Dielectric Square S Updated document to corporate requirements S Added NOTE to Paragraph 2.4 Figure 3 2 of 2 Tyco Electronics Corporation Rev B