44A0221-14-9/9CS3030

SPECIFICATION CONTROL DRAWING Title SCD 44A022X Date TWO CONDUCTOR CABLE, UNSHIELDED, UNJACKETED, 11-3-15 GENERAL PURPOSE, 1000 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 44. Revision C COMPONENT WIRES - 44A021X CABLE CONSTRUCTION DETAILS OUTSIDE DIAMETER (inch) PART NUMBER 1/ CONDUCTOR SIZE (AWG) MAXIMUM WEIGHT (lbs/1000 ft.) NOMINAL MAXIMUM 44A022X-26-* 26 .080 .085 3.2 44A022X-24-* 24 .092 .097 4.8 44A022X-22-* 22 .108 .114 7.0 44A022X-20-* 20 .124 .130 10.4 44A022X-18-* 18 .146 .152 15.4 44A022X-16-* 16 .162 .169 19.6 44A022X-14-* 14 .196 .203 29.6 44A022X-12-* 12 .234 .242 44.4 44A022X-10-* 10 .292 .302 71.7 44A022X-8-* 8 .412 .433 125. 44A022X-6-* 6 .508 .533 190. 44A022X-4-* 4 .616 .647 302. CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 1000 volts (rms) at sea level DIELECTRIC WITHSTAND: 3000 volts (rms), 60 Hz, 1 minute INSULATION FLAWS: Spark Test, 4.0 kV (rms) at 3 kHz Impulse Dielectric Test, 8.0 kV (peak) 1/ PART NUMBER: The "X" in the part numbers above shall be replaced with a conductor material designator as follows: 1 tin-coated copper 2 silver-coated copper 3 nickel-coated copper 4 silver-coated high-strength copper alloy (AWG 26-20 only) The "*" in the part numbers above shall be replaced by color code designators with a slash separating the component wire colors. Example: AWG 20, tin-coated copper conductors; black and brown component wires: 44A0221-20-0/1 NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Page 1 of 1 DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2015 Tyco Electronics Corporation. All rights reserved.