48128

Instruction Sheet  Crimping Dies for SOLISTRAND* Terminals and Splices 408-9786 19 OCT 11 Rev D PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. Crimping Dies for Head Numbers 69065, 69067, and Hand Tool 59973-1 Push Nest Into Yoke Yoke Push Indenter Into Ram Place Screwdriver Here to Remove Dies Nest Indenter Ram Advanced Latch Pin Removed Hydraulic Hand Tool 59973-1 Figure 1 1. INTRODUCTION This instruction sheet provides instruction on application and maintenance and inspection procedures for dies that crimp SOLISTRAND ring tongue terminals, butt splices, and parallel splices. These dies are used to crimp product on solid or stranded copper wires 6.637-117.049 mm²  [13.1-231 MCM]. The dies are used in Hydraulic Heads 69065, 69067 and Hydraulic Hand Tool  59973-1. Read these instructions, and all applicable references, before inserting any die assemblies and crimping any terminals. See Figure 2. NOTE i Dimensions on this document are in metric units with [U.S. customary units in brackets}. Figures and illustrations are for reference only and are not drawn to scale. Reason for revision is give in Section 7, REVISION SUMMARY. 3. DIE INSTALLATION AND REMOVAL Refer to Figure 2 and determine the correct die assembly, wire size, proper product number, and which tool head is correct to use. DANGER AVOID PERSONAL INJURY. Exercise extreme caution when using power unit. Avoid depressing STOP foot switch or trigger control when installing or removing die assemblies. 3.1. Die Installation 1. Remove latch pin on head of crimping head and open yoke. 2. Push nest into yoke until nest snaps into position. 3. Activate power unit to advance ram to approximate position shown in Figure 1. 4. Push indenter in ram until indenter snaps into position. 2. DESCRIPTION (Figure 1) Each die assembly consists of a nest and an indenter, ordered separately, which are retained in the crimping head by ball plungers. The nest is positioned in the © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark yoke of the crimping head and the indenter is positioned in the ram of the tool, in all applications. 5. Return ram to the down position. 6. Close yoke and insert latch pin. TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. 1 of 6 LOC B 408-9786 NOMINAL WIRE SIZE mm² [CIRCULAR MILL AREA RANGE) TYPICAL PRODUCT DIES mm² AWG 7-8 8 6.637-10.539 [13,100-20,800] 33463 RTT♦ 13-15 6 10.539-16.771 [20,800-33,100] 33466 RTT♦ 21 4 16.771-26.653 [33,100-52,600] 34323 BS† 34-35 2 26.653-42.411 [52,600-83,700] 35187 PS▲ 59-60 1/0 42.411-60.551 [83,700-119,500] 36946 PS▲ 67-70 2/0 72.259-96.274 [150,500-190,000] 36948 PS▲ 48133 80-95 3/0 96.274-117.049 [190,000-231,000] 36927 RTT♦ 48134 100-125 4/0 96.274-117.049 [190,000-231,000] 36932 RTT♦ 300430 RTT♦ = Ring Tongue Terminals BS† + Butt Splice TOOL OR HEAD NUMBER NEST INDENTER 48126■ 48355■ 48128-1• 48127-1• 48128■ 48127■ 48129-1• 48127-1• 48129■ 48127■ 48130-1• 48127-1• 48130■ 48127■ 48132-1• 48131-1• 69067 (408-2454) 48132■ 48131■ 48133-1• 48131-1• Hand Tool 59973-1 (4086803) Head Number 69065 (408-2452) 48131 PS▲ = Parallel Splice ■ = also Dies for STRATO-THERM* Heat Resistant Terminals • = Dies for Heavy Duty Terminals Figure 2 CAUTION Ensure the latch pin is fully inserted or damage may occur to the yoke, dies, or latch pin. ! 3.2. Die Removal 1. Remove latch pin and open yoke. 2. Insert blade of screwdriver under nest and pry nest out of yoke. 3. Raise ram to full up position. 4. Insert blade of screwdriver under nest and pry indenter out of ram. used with the wire size or range stamped on the nest and indenter. 2. Center terminal or splice in nest as shown in Figure 4. For best results, when brazed seam on terminal or splice is visible, position seam toward indenter. 3. Activate power unit so that ram advances and holds terminal or splice in place. Do NOT deform terminal or splice wire barrel. 4. Insert stripped wire into terminal or parallel splice until end of conductor is flush with or extended slightly beyond end of wire barrel. 4. WIRE STRIPPING AND CRIMPING PROCEDURE 5. Insert stripped wire into butt splice until end of conductor butts against splice wire stop. 4.1. Wire Stripping 6. Activate power unit to complete the crimp. Strip wire to dimensions listed in Figure 3. Do NOT nick or cut wire strands. NOTE DANGER AVOID PERSONAL INJURY. When operating power unit, exercise caution while holding STOP terminals, splices, or wire near crimping area. i If the terminal sticks in the die after crimping, grasp the wire close to the crimp and apply a rocking motion to remove the die. 7. For butt splice, repeat steps 5 and 6 for other wire barrel. 4.2. Crimping Procedure 1. Ensure the wire range or size stamped on the terminal or splice corresponds with the size being Rev D 8. Refer to Paragraph 5.1, Crimp Inspection, for standard terminal, butt and parallel splice crimp inspection procedure. 2 of 6 408-9786 NOMINAL WIRE SIZE mm² AWG mm² [CIRCULAR MILL AREA) 7-8 8 13-15 STRIP LENGTHS mm [in.] RING TONGUE TERMINALS BUTT SPLICES PARALLEL SPLICES MIN. MAX. MIN. MAX. MIN MAX. 6.637-10.539 [13,100-20,800] 8.334 [.328] 9.128 [.359] 10.319 [.406] 11.112 [.437] 10.319 [.406] 11.112 [.437] 6 10.539-16.771 [20,800-33,100] 9.922 [.391] 13.255 [.522] 11.906 [.469] 12.700 [.500] 11.112 [.437] 11.906 [.469] 21 4 16.771-26.653 [33,100-52,600] 11.509 [.453] 12.302 [.484] 13.493 [.531] 14.288 [.563] 13.493 [.531] 14.288 [.563] 34-35 2 26.653-42.411 [52,600-83,700] 13.096 [.516] 13.890 [.547] 15.081 [.594] 15.875 [.625] 15.081 [.594] 15.875 [.625] 59-60 1/0 42.411-60.551 [83,700-119,500] 18.653 [.734] 20.240 [.797] 15.875 [.625] 17.462 [.687] 17.462 [.687] 19.050 [.750] 67-70 2/0 60.551-72.259 [119,500-150,500] 18.653 [.734] 20.240 [.797] 15.875 [.625] 17.462 [.687] 17.462 [.687] 19.050 [.750] 80-95 3/0 72.259-96.274 [150,500-190,000] 19.050 [.750] 20.637 [.812] 17.463 [.688] 19.050 [.750] 17.463 [.688] 19.050 [.750] 100-125 4/0 96.274-117.049 [190,000-231,000] 19.446 [.766] 20.637 [.812] 17.463 [.688] 10.050 [.750] 10.050 [.750] 20.637 [.812] Figure 3 Inspection Holes of Terminal or Butt Splice Must Face Either Die Center Terminal or Splice Wire Barrel in Next End of Wire Visible Through Inspection Hole Ends of Wires Flush with or Extended Beyond End of Barrel Brazed Seam (Typ) Figure 4 Rev D 3 of 6 408-9786 5. INSPECTION/MAINTENANCE quality and reliability of the crimping die assemblies. Customer-replaceable parts are listed in Figure 2. A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. DANGER Disconnect power supply before performing maintenance, adjustments, inspections, and STOP repairs. These instructions have been approved by Design, Production, and Quality Control Engineers to provide documented maintenance and inspection procedures. Through Tyco Electronics Test Laboratories and the inspection of production assembly, the procedures described herein have been established to ensure 5.1. Crimp Inspection (Figure 5) NOTE i The accompanying procedure is included as an aid to the tool operator ONLY. It is not intended to serve as a quality control procedure for qualifying finished crimps on SOLISTRAND Terminals or Splices. Figure 5 Rev D 4 of 6 408-9786 Inspect crimped terminals or splices by checking the features described in Figure 5. Use only terminals or splices that meet the conditions shown in the ACCEPT column. Terminals and splices displaying the features shown in the REJECT column can be avoided by careful use of these instructions and by performing the maintenance and inspection procedures described in Paragraphs in 5.2 and 5.3. Pitted Broken 5.2. Daily Maintenance It is recommended that each operator of the dies be made aware of, and responsible for, the following steps of daily maintenance: Chipped 1. Remove dust, moisture, and other contaminants from the dies with a clean brush, or a clean, soft, lint-free cloth. Do NOT use objects that could damage the dies. 2. If dies are coated with oil or preservative, wipe clean - particularly in the crimping areas - before placing them in use. 3. When dies are not in use, make certain all surfaces are protected with a THIN coat of any good SAE No. 20 motor oil, and mate and store them in a clean, dry area. 5.3. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the dies or be made available to supervisory personnel responsible for the dies. Though recommendations call for at least a monthly inspection, the inspection frequency should be based upon the amount of use, working conditions, operator training and skill, and established company standards. These inspections should be performed in the following sequence: A. Visual Inspection (Figure 6) 1. Remove all lubrication and accumulated film by immersing the dies in a suitable degreaser that will not affect paint or plastic. 1. Check all surfaces for wear. Inspect the crimp area for flattened, chipped, cracked, worn, or broken areas. If damage is evident, the die must be replaced. B. Gaging the Crimping Chamber (Figures 7 and 8) The inspection requires the use of a plug gage conforming to the dimensions in Figure 8. Tyco Electronics does not manufacture or market these gages. Proceed as follows: Figure 6 2. Align the GO element with the wire barrel crimping chamber. Push the element straight into the the crimping chamber without using force. The GO element must pass completely through the crimping chamber. 3. Align the NO-GO element and try to insert it straight into the same crimping chamber. The NOGO element may start entry but must not pass completely through. If the crimping chamber conforms to the gage inspection, the dies are considered dimensionally correct. If not, they must be replaced. For additional information regarding the use of a plug gage, refer to Instruction Sheet 408-7424. 6. REPLACEMENT PARTS Order replacement dies through your TE Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 7. REVISION SUMMARY Revisions to this instruction sheet include: • Changed company name and logo 1. Mate the dies until it is evident that they have bottomed. Hold the dies in this position. Rev D 5 of 6 408-9786 Dies for Head Numbers 69065, 69067, and Hand Tool 59973-1 “NO-GO" Element May Enter Partially, but Must Not Pass Completely Through the Die Closure “GO" Element Must Pass Completely Through the Die Closure Dies Bottomed but Not Under Pressure Figure 7 DIES DIE CLOSURE DIM. “A” GAGE ELEMENT DIM. “B" NEST INDENTER GO NO-GO GO NO-GO DIM. “C" RADIUS “R" 48126 48355 2.54 [.1000] 2.692 [.1060] 2.54-2.548 [.1000-.1003] 2.689-2.692 [.1059-.1060] 7.92 [.312] 3.18 [.125] 48128-1 48127-1 3.911 [.1540] 4.115 [.1620] 3.911-3.919 [.1540-.1543] 4.112-4.115 [.1619-.1620] 11.09 [.437] 4.34 [.171] 48128 48127 3.911 [.1540] 4.115 [.1620] 3.911-3.919 [.1540-.1543] 4.112-4.115 [.1619-.1620] 11.09 [.437] 4.34 [.171] 48129-1 48127-1 4.699 [.1850] 4.902 [.1930] 4.699-4.706 [.1850-.1853] 4.899-4.902 [.1929-.1930] 11.09 [.437] 5.54 [.218] 48129 48127 4.699 [.1850] 4.902 [.1930] 4.699-4.706 [.1850-.1853] 4.899-4.902 [.1929-.1930] 11.09 [.437] 5.54 [.218] 48130-1 48127-1 5.410 [.2130] 5.613 [.2210] 5.410-5.418 [.2130-.2133] 5.610-5.613 [.2209-.2210] 11.09 [.437] 6.35 [.250] 48130 48127 5.410 [.2130] 5.613 [.2210] 5.410-5.418 [.2130-.2133] 5.610-5.613 [.2209-.2210] 11.09 [.437] 6.35 [.250] 48132-1 48127-1 6.172 [.2430] 6.375 [.2510] 6.172-6.179 [.2430-.2433] 6.372-6.375 [.2509-.2510] 11.09 [.437] 7.52 [.296] 48132 48131 6.172 [.2430] 6.375 [.2510] 6.172-6.179 [.2430-.2433] 6.372-6.375 [.2509-.2510] 11.09 [.437] 7.52 [.296] 48133-1 48131-1 6.959 [.2740] 7.163 [.2820] 6.959-6.967 [.2740-.2743] 7.160-7.163 [.2819-.2820] 14.27 [.562] 8.33 [.328] 48133 48131 6.959 [.274] 7.163 [.2820] 6.959-6.967 [.2740-.2743] 7.160-7.163 [.2819-.2820] 14.27 [.562] 8.33 [.328] 48134 48131 7.823 [.3080] 8.026 [.3160] 7.823-7.830 [.3080-.3083] 8.023-8.026 [.3159-.3160] 14.28 [.562] 3.525 [.375] 300430 48131 8.788 [.3460] 8.991 [.3540] 8.788-8.796 [.3460-.3463] 8.989-8.991 [.3539-.3540] 14.28 [.562] 10.693 [.421] Figure 8 Rev D 6 of 6